Does Revit 2011 have and means of duplicating a wall then modifying it to include top and bottom plates - or does a wood stud wall with plates already exist in some available library?
View 9 RepliesI have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View RelatedIs there a way to slope the bottom of the wall. See attached x sec.
View 2 Replies View RelatedI have drawn an existing building thats needs a renovation. In the project i need to add 100mm insulation to the external side of the outer walls. Are there any way that i can add theese 100mm to my existing walls but only show the new 100mm in new construction ?
View 1 Replies View RelatedThe only door I can find to insert into a glass curtain wall is a simple glass single door with a handle. I know this is a very particular thing and any door won't work. My door needs to have stiles and rails like most doors in storefronts or curtain walls. How do I create a type with these features? Do I need to create a family from scratch?
View 1 Replies View RelatedWe have a buildig form which is developed as a sweep form. The form is made as a generic family. When the form is placed in the project, we are able to see the cut lines as in plan but when we try to draw floor plates which are to be generatd from the intersecting lines of the form in respective levels, we are unable to select the cut lines.
how can we generate the floor plates which are linked to the cut lines?
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRefer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
I'm the happy owner of the new Corel VideoStudio Pro X5 program. I've resently put together my first video, but then an error occured.
In the preview window i noticed that every time a new clip is being played, the program adds a top line and bottom line, often displaying something from the previous clip in the timeline. I thought this was not a big deal, but then after saving my video as a finish .avi file, the problem was not solved..
On following webpage, there's a screen picture of my problem: [URL] ...
The clips are recorded with a 4:3 ratio and 720p, 60 frames/s. When i played the finish created file, i tried in Windows Media Player and in VLC.
How do you control the bottom depth of a toposurface? I have a structure with a basement and the "Earth" stops at the top of the footings so that my details show the footings floating in space!!
View 2 Replies View RelatedHow can I make the bottom of stair to flat instead of steps?
View 5 Replies View RelatedCan sweep profile cut up to the bottom of stair stringer?
Find attached.
Is there anyway no wall gap line between floor when I copy 1st floor walls to 2nd floor. Not to use "Join geometry" & Line work: invisible line" tools? See attached picture.
View 3 Replies View RelatedShort story is I made a wall sconce from scratch but I can't see the symbolic lines in my ceiling plan in the project.
I needed a linear wall sconce for a client presentation based on one of theirs already installed. The manufacturer doesn't provide BIM for this model so I had make my own. I haven't bothered with photometrics. At this point all I need is a placeholder for the ceiling plan and a 3D model for a hidden line view. I used the wall based light fixture family. There was a plane elevation but no apparent parameter so created one and called it 'mounting height'. After about ten minutes of modeling (and over an hour of tedious aligning, dimensioning and locking of the sketches to keep the model from distorting with changes in wall thickness) I opened the ceiling reference level plan and drew some symbolic lines to represent the fixture on the ceiling plan in my project.
Here's what happened.
The symbolic lines for the CPRL (Ceiling plan in the family editor) are also visible in the FPRL. I don't know why this is and there doesn't appear to be a way to hide them in just one plan. I suspect it's because both are at the same height (the reference level.) I tried changing the working plane before drawing the symbol lines to another plane above the reference level and out of its view range but it had no effect. I can still see them in the floor plan.When I loaded it into the project nothing appeared and I got the message about 'no elements are visible because yada yada'. The symbolic lines didn't show up at all. I checked the detail level and that wasn't it. As far as I can tell the view range for the CPRL and the RCP in my project are the same. They don't show up in the project floor plan either. The sconce is visible in 3D views so it's definitely in there. I tried monkeying with the height of the symbolic lines like I stated in part 1. but it had no effect on there visibility. Symbol lines are visible in other families so it can't be an issue with visibility overides.In my project I noticed there's a parameter for the fixture called 'Elevation'. Changing it moved the fixture up and down on the wall. Changing the 'mounting height' parameter in the project had no effect! This parameter worked fine in the family editor. Playing with the 'Elevation' parameter and the cut plane elevation brought the symbolic lines into view. Apparently the symbolic lines are only visible when the cut line is passing through the sconce. Unfortunately my sconce needs to be mounted at 6 ft and my cut plane is at 7'2 to avoid cutting doors and windows. How do get these symbolic lines to display?
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
I want to turn off a metal stud wall but leave visible the pre-cast wall.
View 5 Replies View Relatedrevit should give a sub category for wall so it easy to on and off using visibility and give different line color in the object style
View 2 Replies View RelatedIn any event, how do does one use the numerical offset to offset an exterior wall and achieve the new offset wall to be in the correct orientation and location, i.e. exterior brick on the exterior and interior gypsum board on the interior?
View 2 Replies View RelatedI need to model a wavy wall in Revit. See attached.
Revit 2014
I am trying to create wall by faces of a Mass I modelled.
This is the Mass: [URL]
Everytime I try to create a wall by face of one exactly face, it accept Location Line: By Finish Face Interior only, when I try to change ANY other Location Line, it gives me a message error.
[URL]
And it is always from the SAME FACE highlighted at the picture.
The mass was made by the floors and top edges. I select all of the edges and create a mass from down to top.
All the other faces are ok and they accept the wall by face and let them change the Location Line except this one.
how to have different colors for different wall faces? Like all have a plaster finish on the external side, but the colors are different, but when I try to change the color of the external finish, it changes it for all the walls.
View 5 Replies View RelatedI've inserted walls etc in the "Existing" phase.
How do I show them demolished?
In the "New Construction" phase do I need new wall types?
I am trying to change the wall assembly of my foundations (getting rid of a layer of EIFS) and it won't let me delete the layer or change the width (although I can change it into an airbarier). Is there any way to control what parts of the wall are locked in the "edit assembly" window?
I am very new to Revit and am using a student version, I'm nt sure if that changes things.
Cannot insert any window in this wall (its 140mm blockwork single skin trimmed to the roof above) and tried different window families. Yet I can cut an opening and also insert any door.
View 4 Replies View RelatedI can tag walls by entering the wall type in the 'type mark' box in the assembly's properties, but is there a way of listing out the material of each type of wall that has been used in the project. e.g:
Wall Type P1
16mm Gypsum Board
92mm Steel Stud
16mm Gypsum Board
I added base to wall in sweep and I change to interior or exterior in Wrapping at Ends. It does not show any base at end wall. Did I miss anything? How I can make it work?
View 2 Replies View RelatedI'm using RS2013. My stacked walls are not displaying in preview when editing them. Why would this happen? Even the out of the box walls are not showing. The wall shows fine in the model. This is the first time I have has this happen. I tried scrolling and panning the preview to look but to no avail.
View 6 Replies View Related