I remember using it once for my commercial job in older version. I think it was ver. 11 or 12. Today when I tried HC separations, black appeared in all plates and a change I noticed is that all the colors are changed to Pantone HC process. I remember it well, it used to be CMYK + Pantone orange + Pantone Green.
I don't remember about the black color if it was separated on each plate or not.
Having problems getting the advance key to highlight in this area. I have repeated these instructions and problem still is not resolved.
This is the area that I am having problems with. To customize a halftone screen.
1. Click File Print.
2. Click the Color tab.
3. Enable the Print separations option.
4.Click the Separations tab.
5. In the Options area, enable the Use advanced settings check box.
6. Click Advanced.
7. Change any of the following settings:
•Screening technology
•Resolution
•Basic screen
•Halftone type
You can set the screen frequency, screen angle, and overprint opt. ions for spot colors as well as process colors. For example, if you have a fountain fill made up of two spot colors, you can set one to print at 45 degrees and the other at 90 degrees.
I have a Roland SP54 with VersaWorks.
I design everything in CorelDraw and want to know how one goes about doing a color separation for cutting just the vinyl,
E.g. I have a 3 color design that I need to cut 3 different color sheets of vinyl. How do I go about setting up to cut?
How can I save the separations without having to manually seperate them into a printable file for the screen printer?
Is there a way I can print seps to file?
I print spot color separations using CorelDraw a lot. Just ungraded from X3 to X5. One problem I am having is in the printing dialog. When a file has, say, 4 colors showing up in the separations section I may only want to print 2 or three of them. I deselect the ones I don't want - but all 4 seps come out. I am wasting a lot of expensive separations.
View 3 Replies View RelatedThis discussion is on using RGB file creation techniques to output to ink jet devices. I posted the comments below the link because color management off always pops up in the conversation as it turns to non-postscript devices so I wanted to circumvent the side bar conversation.
[URL]....
First let's get this straight, I've written it and said it about a thousand times, you cannot turn off color management.
When you select simulate color management off in the default application color management dialog, CorelDRAW simply utilizes a different set of color management settings. The rules of color management never change! The application requires guidelines on color and still must have rules that govern conversions, PERIOD.
These rules are not different, only the engines, rendering intents and profiles change. These setting in X5 and X6 can be, in some cases adjusted to simulate previous setting in versions prior to X5 that were labeled color management off, but this label in older versions (X4 and older) were deceptive in their nature, color management was never turned off, just set to a specific configuration.
Simulate color management off (in X5/X6) uses wide gamut cmyk simulation as the CMYK profile, it disengages the color engines (setting CorelDRAW to another internally controlled process) and sets the interface to RGB. It does not turn color management off.
These settings have many uses for industries such as laser engraving and screen printing separations and I support their continued use. Do not confuse this and use these settings for professional output using press work, ink jets or digital printers.
In my color separations in print preview the "use advanced settings" is disabled.
I have loaded cdr graphics suite 12 on my new laptop w/windows 7, and also on my old machine that I have loaded windows 7 on. Cannot register the program any more due to outdated version. problem exists on both computers.
There are other minor issues but this one I use regularly.
I have a complex (includes tints) clip art object that needs printing in a specific pantone color I just convert it to grayscale using edit>find and replace objects>color mode. then print it as a black plate and just use another color on press.
Today I had to send off artwork to another printer. Dang. How to install a macro. Import clip art to be modified to a new document, do not do this in your working document.
Use Edit>Find and Replace> Find Objects
Replace a color model or palette. Next
Leave as is except change Replace with color model to "Grayscale" Next>Replace all
Repeat 2-4 for 'outlines' if you have them.There you now have a gray scale clipart, but the fun continues!You'll need to know what pantone color you want to use. Let's say Reflex Blue. Make a square and color it Reflex blue from a pantone palette.Duplicate the square and create swatches at 90% 80% 70% etc down to white.Select these square swatches, then Windows>Color Palette>Create Palette from Selection. Save palette with a temporary name, it is only time use. Or you could call it 'Reflex Blue'Now go to this website and download the macro "limit colors" URL...
Drop it in your GMS folder in under your username to install the macro. (might have to save the drawing and restart Corel...)Once you reopen your now grayscale clipart document, Select the clipart. Run the macro (Tools>Macros>Run Macros) LimitColors.Posterize select the number of colors in your new palette if you created 10% swatches, go with 11, if you did steps of 20% then you'll do 6 (don't forget white).Run the macro LimitColors.LimitColors and select your new palette you made in step 9.
why (sometimes) when I export text or graphics as .eps files to my cutter it cuts the same outline up to four to five times and ends up cutting right through the backing paper. I have been using postcut with various corel editions since 1997 with no problems until recently. It also cuts random lines through lines of text which is such an expensive pain in the ass.
I started to use the production manager in flexi sign to cut my designs and same thing happens, except for the random lines but it will make up to five cuts on some objects. All text and graphics are exported the same. Has something in corel newer versions changed in relation to this?
We are having a big problem with dropping lines of text or parts of graphics. It is happening on 3 different laser systems and 2 different printers.
View 14 Replies View RelatedOften whatever I'm working on in X4 disappears off the document page when I zoom in or out. It's still there (I can see it in the print preview)and I can print it, but I can't see it no matter what view (e.g., normal, draft, etc.) I select. If I select the entire page I can see the graphic and text handles, but nothing else. The only way I can see my work again is to save it, close the program, and then re-open the file. My computer is a Dell Precision Work Station T3400 running Vista Ultimate with an Intel Core2 Quad CPU, 4GB RAM, and my graphics card is an NVIDIA Quadro FX 570 256MB. All my software and drivers are up to date. The problem occurs no matter what screen resolution or refresh rate I'm using.
View 6 Replies View Relatedi´m using CRD since X3 so I think i´m quite experienced with all the crashes and uncompatibilities but now I have a problem which I can´t solve.
I made a graphic project which is quite large (2,6m x 2,0m @ 300dpi) and including raster grahics. The CDR file itself has about 400MB. When I tried to export this graphic to the png or jpg at the current size Corel X5 always crashes. I tried almost everything on many computers but always the same problem.
It looks like the project is too large for export. At this moment I desperately need to export the file to jpg or png at full resolution. Maybe X6 is more stable when exports or I have to simplify the project somehow but...
FILE IS UPLOADED here and I need to have it 2,6m x 2,0m: [URL]
I have a 900 x 500 px image in Adobe Illustrator, which overlaps a bit the canvas on the left side.
When I open this file with Corel, it adjusts my graphics so that it's centered on the screen. The AI file is centered on another point. Also, the canvas Corel creates is A4 sized. I always have to resize the canvas and then manually adjust the position of my graphics.
Question: How can I save an AI file so that when I open it at Corel, the position and size of the canvas will be exactly the same?
Entire Corel suite freezes on start up - I cannot do anything. Reinstalling also does not work - suddenly buttons on the installer dissapeared - there is no text on them and when I click them nothing happens.
A week ago I have installed service pack 3 and everything worked fine. It has all gone wrong again. And installation of the latest patches does not work anymore.
I am running Windows 7 64-bit and I've got a feeling that is must have something to do with system updates.
When printing separations, you're having issues printing more than three plates. I've got the OPPOSITE issue: When I'm trying to print only one or two colors of a graphic, it prints all of them.Example:I have black, PMS-A, and PMS-B in my graphic, but I only want to print PMS-A and PMS-B.I deselect black in the separations window, and that should be it, right?Hit print, and all of them print...black included.
I've tested it on multiple printers, and get the same results.This only started happening after my X6 upgrade.
P.S. I should add that when I take the same steps, and then print to file, it still saves all of the plates, not just those selected.
I just installed Update 4 for Corel X6 and now I can't print separations from the HP5000 printer. I can composites. When I go to print, the error message says "Nothing is selected to be printed. Check your page range and/or separations settings". It shows current document to print and separations to be printed. It will not advance to the print preview page. It printed perfectly before Update 4.
I need to print separations. I can export out and PDF and print from Illustrator, but what a pain. Should I just do a system restore and forget Update 4 for now?
I often create graphics in CorelDRAW export it and inserting it into my MS Word documents and finally convert my documents to pdf. When it is vector graphics, exporting as EPS works fine: The increase in file size is small and lines are displayed perfect independant of how much you zoom in the final pdf document. When I handle bitmaps, I usually export as JPG (or PNG), which works well too. My problem arise when I have a mixed vector and bitmap image. I have imported a bitmap into CorelDRAW and created some lines on top of it. I want to export it as a whole. If I export as EPS, the final result is fine, but filesize has increased considerable. If I choose to export as jpg, the filesize is fine, but the lines are getting slightly blurry. Is there a way to get the best of both Worlds - resonable filesize and perfect lines? Maybe settings in some dialog??
View 7 Replies View RelatedHow on earth do you export bitmaps cropped to the size of the canvas? This seems like the simplest functionality ever but i can't get it to work. For example, I am designing an advert for use online. It needs to be 600px wide x 150px high. I may want to use a background image or a photo that when placed goes beyond the edge of the canvas. Logic dictates i would only want to export the canvas with a web image (otherwise why would i have set an exact number of pixels.) However, Corel insists on exporting everything on the canvas and desktop. Surely it should allow us to choose the bounding area of the exported bitmap.
Just to clarify what I mean, i've included a screen shot showing and example original graphic and the export result. I'm sure there must be an easy way to do this. If it's one like this i can crop it easily, but sometimes a print customer will ask me to send them, for example, a 32pp booklet we have designed for them with each page as a JPG and to crop each one manually is a right pain.
X5 Recently have begun missing parts of print out. Tried to duplicate but appears completely random.
Output to both Full colour laser and Wide Format printers will miss either text or part of objects. Today printed the text but not the text effects. Initially closed and reopened, rebooted, However this has become a now daily feature so regardless tried reprint from the same screen so next print has everything included.
Very costly and time consuming - print preview shows all correct but output is not the same.
Running Win 7 64bit 8GB Ram
I have some Ai files that I need to open in X6 but they use linked images which I have, but when opening in CorelDraw all I get is the basic Ai stuff but not the linked images, is there an easy way to open the Ai file and see it as it was intended?
As a sub note I can't go back to the supplier of the Ai file to make any changes.
I just used the help file for the first time in ages and noticed all the links to the graphics are broken hence no diagrams etc. I tried to search out where they are usually stored and it gives some weird Address under properties. It's a vba so suppose it's a database? How do I restore the links without having to do a re-install?
As to the pen: How do you stop the annoying over-the-top predictive curve that happens past the node in the next section after a long drag to form the first curve. i.e. you simply want to draw a straight line after dragging out a curved section previously and you get this unmanageable curve to deal with ?
02012013010.jpg
Blank Blocks behind text and graphics
After a "format c:" i´m trying to reinstall my corel x5. But after starting the install-progress i only can see this:
What does it mean? I can´t imagine where this comes from?!? How to handle this fault?
I am building a new desktop and am thinking about using dual graphics cards for my work in Corel X5. Ive seen nothing in technical specs or min requirements that even alludes to the program being able to take advantage of an SLI configuration (evga gtx 465 superclocked with 1gb ddr5).
View 5 Replies View RelatedClient supplies me with word document, I make a PDF from it and then from Acrobat create an ESP file, this is done as an eps file is much less likely to cause probs then importing a PDF, I then print from the Coreldraw file with the EPS pages no problem. The problem then arises when I have to then create a PDF file from COreldraw for the client - any EPS files in the document do not appear in the PDF - so there lies the problem.I cannot alway directly import a PDF file (often screws up) even if I save fonts as outlines. Saving as EPS overcomes most/all issues.
View 3 Replies View RelatedI have a client that I laser engrave parts with a variety of graphics, about 35 different designs that fit on 10 different parts and all the designs are different sizes on the parts. I use a fixture that holds 40 parts, two rows of 20, for each type of part. I have a master file for each part that contains a page with each graphic laid out as in the fixture so that I can simply go to the page and select the graphic in the right position for the fixture and paste it into a "lasering" file. The lasering file is just as many pages as I need to run the order and is much smaller than the master file.
That works fine now and is actually pretty quick and easy to setup, but I just found out that they will be adding about 35-40 designs a month. That will make the master file huge and very cumbersome to manage, not to mention the order sheet (spreadsheet) will get huge in no time at all. I can envision it becoming a nightmare to manage and mistakes will be frequent due to the sheer size of the files.
What I would like to do is have a spreadsheet with the graphic and a quantity and merge that into the lasering file instead of doing it manually. I am very familiar with merging data but I don't know if it's possible to merge a graphic from a database or somehow import the graphic into corel.
When I checked my computer for any any unused programs I got see this coreldraw (r) graphics suite x5 installed. When I got to uninstall it showed and error message that some sort of setup.xml is missing. When I checked this programs folder I got to see that there are two corel folders [Corel and Corel (2) ] in my C: drive. After checking all the file locations of different corel applications I deleted the Corel (2) foder. After that also corel was not being uninstalled. I don't want to re-format my computer only for this
View 1 Replies View RelatedHow do I change the Default Advanced Separations Settings?
View 1 Replies View RelatedIm using draw x5 graphics software and want to know where to find useful for properly sizing web friendly graphics. I want to build a banner and an icon for my new site.
View 3 Replies View RelatedHow do I convert 4cp files to hexachrome in CS5.5
View 2 Replies View Relatedhow to export png from corel?
View 3 Replies View Related