CorelDRAW Graphics Suite X3 :: Color Separations Saved As CDR File
Mar 14, 2012How can I save the separations without having to manually seperate them into a printable file for the screen printer?
Is there a way I can print seps to file?
ADVERTISEMENT
CorelDRAW Graphics Suite X6 :: Advance Tab In Color Separations
Nov 12, 2012Having problems getting the advance key to highlight in this area. I have repeated these instructions and problem still is not resolved.
This is the area that I am having problems with. To customize a halftone screen.
1. Click File Print.
2. Click the Color tab.
3. Enable the Print separations option.
4.Click the Separations tab.
5. In the Options area, enable the Use advanced settings check box.
6. Click Advanced.
7. Change any of the following settings:
•Screening technology
•Resolution
•Basic screen
•Halftone type
You can set the screen frequency, screen angle, and overprint opt. ions for spot colors as well as process colors. For example, if you have a fountain fill made up of two spot colors, you can set one to print at 45 degrees and the other at 90 degrees.
CorelDRAW Graphics Suite 12 :: Color Separations For Vinyl Cutting
Jul 4, 2011I have a Roland SP54 with VersaWorks.
I design everything in CorelDraw and want to know how one goes about doing a color separation for cutting just the vinyl,
E.g. I have a 3 color design that I need to cut 3 different color sheets of vinyl. How do I go about setting up to cut?
CorelDRAW Graphics Suite X5 :: Color Separations - Printing Dialog
Apr 4, 2011I print spot color separations using CorelDraw a lot. Just ungraded from X3 to X5. One problem I am having is in the printing dialog. When a file has, say, 4 colors showing up in the separations section I may only want to print 2 or three of them. I deselect the ones I don't want - but all 4 seps come out. I am wasting a lot of expensive separations.
View 3 Replies View RelatedCorelDRAW Graphics Suite X6 :: Color Management Printing RGB / CMYK And Separations
Nov 11, 2012This discussion is on using RGB file creation techniques to output to ink jet devices. I posted the comments below the link because color management off always pops up in the conversation as it turns to non-postscript devices so I wanted to circumvent the side bar conversation.
[URL]....
First let's get this straight, I've written it and said it about a thousand times, you cannot turn off color management.
When you select simulate color management off in the default application color management dialog, CorelDRAW simply utilizes a different set of color management settings. The rules of color management never change! The application requires guidelines on color and still must have rules that govern conversions, PERIOD.
These rules are not different, only the engines, rendering intents and profiles change. These setting in X5 and X6 can be, in some cases adjusted to simulate previous setting in versions prior to X5 that were labeled color management off, but this label in older versions (X4 and older) were deceptive in their nature, color management was never turned off, just set to a specific configuration.
Simulate color management off (in X5/X6) uses wide gamut cmyk simulation as the CMYK profile, it disengages the color engines (setting CorelDRAW to another internally controlled process) and sets the interface to RGB. It does not turn color management off.
These settings have many uses for industries such as laser engraving and screen printing separations and I support their continued use. Do not confuse this and use these settings for professional output using press work, ink jets or digital printers.
CorelDRAW Graphics Suite 12 :: Color Separations Advanced Settings Disabled
Dec 12, 2010In my color separations in print preview the "use advanced settings" is disabled.
I have loaded cdr graphics suite 12 on my new laptop w/windows 7, and also on my old machine that I have loaded windows 7 on. Cannot register the program any more due to outdated version. problem exists on both computers.
There are other minor issues but this one I use regularly.
CorelDRAW Graphics Suite X5 :: Change Full Color Or Gray Scale Clipart To Pantone For Printing Separations
Dec 2, 2011I have a complex (includes tints) clip art object that needs printing in a specific pantone color I just convert it to grayscale using edit>find and replace objects>color mode. then print it as a black plate and just use another color on press.
Today I had to send off artwork to another printer. Dang. How to install a macro. Import clip art to be modified to a new document, do not do this in your working document.
Use Edit>Find and Replace> Find Objects
Replace a color model or palette. Next
Leave as is except change Replace with color model to "Grayscale" Next>Replace all
Repeat 2-4 for 'outlines' if you have them.There you now have a gray scale clipart, but the fun continues!You'll need to know what pantone color you want to use. Let's say Reflex Blue. Make a square and color it Reflex blue from a pantone palette.Duplicate the square and create swatches at 90% 80% 70% etc down to white.Select these square swatches, then Windows>Color Palette>Create Palette from Selection. Save palette with a temporary name, it is only time use. Or you could call it 'Reflex Blue'Now go to this website and download the macro "limit colors" URL...
Drop it in your GMS folder in under your username to install the macro. (might have to save the drawing and restart Corel...)Once you reopen your now grayscale clipart document, Select the clipart. Run the macro (Tools>Macros>Run Macros) LimitColors.Posterize select the number of colors in your new palette if you created 10% swatches, go with 11, if you did steps of 20% then you'll do 6 (don't forget white).Run the macro LimitColors.LimitColors and select your new palette you made in step 9.
CorelDRAW Graphics Suite X5 :: Hexachrome Separations In X4
Mar 14, 2011I remember using it once for my commercial job in older version. I think it was ver. 11 or 12. Today when I tried HC separations, black appeared in all plates and a change I noticed is that all the colors are changed to Pantone HC process. I remember it well, it used to be CMYK + Pantone orange + Pantone Green.
I don't remember about the black color if it was separated on each plate or not.
CorelDRAW Graphics Suite X6 :: Saved CDR File Doesn't Open
Dec 4, 2012when i open or import it ,then that shows me "Read error" i can open it again.and it has large size, so i cant attach here....
View 3 Replies View RelatedCorelDRAW Graphics Suite X5 :: Check Existing CDR File To See Which Version It Is Saved In?
May 1, 2010With the sad fact that we have to save files into older versions of Corel for other people to open in their Corel Draw, is there an easy way to check an existing CDR file to see which version it is saved in? File-Document Properties DOES NOT seem to do it, although that would be a great place to have it.
View 15 Replies View RelatedCorelDRAW Graphics Suite X6 :: Cannot Open Saved File - TEMP Or Output Drive May Be Full
Dec 25, 2013I have saved a file in corel. on the second day, when i want to open the file,is writting: "File Copy Error" TEMP Drive or Output Drive may be Full" Is there any posibility to recover the file. The recovery toolbox can not recover the file.
View 14 Replies View RelatedCorelDRAW Graphics Suite X6 :: Color Profile - Making File Smaller?
Nov 25, 2013What kind of problem can occur when saving files ".cdr" without Color Profile in order to reduce the file size when sending it to print shop? Is Color Profile really necessary?
View 14 Replies View RelatedCorelDRAW Graphics Suite X4 :: Make File Into Process Color Like CMYK For Plates?
Apr 4, 2013I need to know if i can make a file into a process color like cmyk for plates. How would i do that
View 5 Replies View RelatedCorelDRAW Graphics Suite X6 :: Crashing When Opening Saved Files?
Jul 13, 2012I find when i open any file i have saved as an X6 file CorelDraw crashes ...the only way it works is if i open a blank template or older file (not saved in x6) first
View 11 Replies View RelatedCorelDRAW Graphics Suite X6 :: Printing Options Not Saved With Print Merge?
Nov 23, 2012Whenever I perform a PrintMerge the print dialog and its options are reset everytime I leave the print dialog.
Usually you hit print set parameters and hit apply, you now can cancel the dialog and hit print again, your previous settings should still be there. Same goes if you actually print and want to repeat the print process, as long as you dont close the document. This works for normal printing but fails with print merge.
Every time I close the dialog (not the document) all the settings are back to default. This did not happen in X5 and is very annoying since it resets to default even if you actually hit print, forcing you to set the parameters every time.
CorelDRAW Graphics Suite X6 :: Saved Export Preset Transformation Setting Changes
Feb 4, 2013I export many web graphics at the same size so with x6. I thought I would love the presets with x6 however when I set the preset to export like at 700px width it changes and re-sizes the exported graphic to 350px width. It show 700px on the screen when I load the preset however right when I click export or if I place me cursor in the transformation box it changes. I even tried to change it too 1400px hoping it would then change it to 700px but it still changes it to 350px.
View 2 Replies View RelatedCorelDRAW Graphics Suite X4 :: Saving Tone Curve Settings Saved In Different Directory
Mar 31, 2011CorelDraw X4 sp4 w/ hotfix
Why is it that when in Draw save the tone curve settings it saves in a totally different directory? Then if I want to open that settings file it takes me somewhere else showing default styles/settings (*.crv)?
CorelDRAW Graphics Suite X3 :: Page Numbering Doesn't Work On Specific Saved Files
Dec 29, 2011I have the page numbering macro. It works on new files; however, it doesn't work on specific saved files. What could be wrong with those files? Is there any way to enable the page numbering macro in those files?
I use Corel Draw X3, by the way.
CorelDRAW Graphics Suite X5 :: Apply Color To Selected Objects Without Having To Search For Color In Color Palette
Mar 13, 2012Is there a way to apply a color to selected objects without having to search for the color in the color palette. So say if I am working with an image that has multiple colors but want to use only one of the colors in that image, is there a way to apply it without having to create or add it to the palette.
View 3 Replies View RelatedCorelDRAW Graphics Suite 12 :: Make Outline Color Of Object Same As Fill Color?
Dec 5, 2011I still use Corel Draw 12 and my question is is there an easy or automatic way to make the outline color of an object the same color as the fill color? I do it the hard way of trial and error until I get the right outline color from the color dock/pallette.
View 10 Replies View RelatedCorelDRAW Graphics Suite X6 :: Latest Update - Custom Color Resets To Default Color
Sep 2, 2013I'm having a major issue here, I use custom colors (created in my custom palette), X^ used to hold it very nicely, even in PDF exports etc.
Now - with the latest update, X6 "forgets" the custom colors, it resets it to default color, I have to manually set every object to the custom color all over again.
CorelDRAW Graphics Suite X5 :: Transform 4 Color Picture To 2 Color
Sep 8, 2012Is there anyway to transform a 4-color CorelDraw picture into a 2-color one at reasonably good quality?
The problem I met is at the galley.
I could, or might, only be able to get a 2-color printer at reasonably good price.
The original design is 4-color. But the actual detail is not very important.
They are book covers, which only need to protect the book.
The exported picture is shown below:
CorelDRAW Graphics Suite X6 :: Color Styles And 2 Color Artwork
Apr 15, 2012To create 2-color artwork from any colored vector clipart I used to be able to:
import colored clipart convert to CMYK if needed select entire graphic and create new styles with 2 parents change (edit) the colored parent to a named Pantone spot color (the child colors automatically become percentages of the Pantone spot color) "find and change" the remaining CMYK to Grayscale, and then back to CMYK (this ignors the spot color and converts the annoying rich blacks to percentages of K) export to a PDF file--which when imported into, say, InDesign, will separate on the K and Spot Color Plates only, in all its glorious shades of gray and tints of Pantone spot color.
I'm completely at a loss on how to do this in X6, and I'm on a short deadline.
Illustrator :: How To Print Color Separations As A Postscript File CS5
Feb 15, 2012I'm trying to print color separations as a Postscript file from Illustrator CS5 and the halftone areas keep showing up as grayscale instead of the specified frequency and angle. I've tried usiing multiple PPDs and options but I'm having no luck.
View 15 Replies View RelatedCorelDRAW Graphics Suite X6 :: Opening AI File That Have Linked Graphics
Jun 19, 2013I have some Ai files that I need to open in X6 but they use linked images which I have, but when opening in CorelDraw all I get is the basic Ai stuff but not the linked images, is there an easy way to open the Ai file and see it as it was intended?
As a sub note I can't go back to the supplier of the Ai file to make any changes.
CorelDRAW Graphics Suite X4 :: Links To Graphics Are Broken When Using Help File
Oct 18, 2012I just used the help file for the first time in ages and noticed all the links to the graphics are broken hence no diagrams etc. I tried to search out where they are usually stored and it gives some weird Address under properties. It's a vba so suppose it's a database? How do I restore the links without having to do a re-install?
As to the pen: How do you stop the annoying over-the-top predictive curve that happens past the node in the next section after a long drag to form the first curve. i.e. you simply want to draw a straight line after dragging out a curved section previously and you get this unmanageable curve to deal with ?
CorelDRAW Graphics Suite X4 :: What Does CV Mean At End Of A PMS Color
Apr 9, 2013What does the CV mean at the end of a PMS color and what is the difference between C and CV? I know it's a coated color.
View 2 Replies View RelatedCorelDRAW Graphics Suite X6 :: Printed Color Is Different
Jul 16, 2012When I print the same file out of X6 & X4 the color is much different. I know this has to do with color management but now sure how to correct. The color coming from X4 is much better.
View 2 Replies View RelatedCorelDRAW Graphics Suite X5 :: Color Management
May 31, 2011What is the default color management setting (all the setting) that Coreldraw X5 is set to after installation. We had a tech guy from our local printer chage the values and now we only have problems
View 5 Replies View RelatedCorelDRAW Graphics Suite X6 :: Color Separation In V16.4
Aug 29, 2013Yesterday CD upgraded itself as I turned it of to go home from work, when starting it the day after all seemed to be as it was util I should print out a color separation. Suddenly I now have to check every color that I want to print out, the only color that doesn't need to be checked is black(cmyk black) all pantoen colors have to be checked.
Why is this changed?
Can I set it up so all colors is to be printed as default?
Also having some trouble in exporting to EPS, when exporting all seems fine, but the file appears to be empty, the next exported files seems to be fine thou. First export is always empty.
CorelDRAW Graphics Suite X3 :: Color Conversion
May 10, 2011For our sublimation printing, we use Corel X3,
For some time we have problems with the colors.
As standard pallette we use Pantone Coated, but after I export a .cdr to .eps some colors are replaced with a new color with the same name, when I open it in Coreldraw again afterwards. The colors are placed in a new user pallette and have different CMYK values.
How knows how to keep my PMS coated pallete?