I have to draw hundreds of lines that have same start point. How can i do this?
I am trying to insert a picture but seem impossible for me. Sow i have lines with the same start point and different endpoints. There is a short way to do this. so avoid to enter the same start point for hundreds times or snap the the same point infinitely... what about Copy with grips or Change command in this case?
I want to add say a circle and an arrow at the two ends of a line. I am able to do it using Blocks for one single line by inserting the blocks at desired locations. But how to do it for say all the lines in a drawing or shape file without customization.
View 1 Replies View RelatedI have been searching for a macro to export the start and end point of a line coordinates to excel, but I can only find information on how to export 3D Points.
Is it possible to program a macro that allows me to export the start and end point of various lines in a sketch?
The objective of this is to connect an excel file which is updated when I create a line with it correspondent points, then i could not only import these x,y,z coordinates from excel to inventor but I whould be able to update my spreedsheet whenever I change my sketch.
I have a very frequent need to draw lines that radiate out from a point on different bearings and distances. I think of this as a sideshot.
_/_
|
Civil 3D’s sideshot command acts differently. It draws lines between the radial end points.
/
|
Do you know what command is needed to do what I want? It is not the Create Line by Side Shot command.
I need to be able to draw "squiggly" (multi-point)lines. Specifically, roads on a map. Is there any tool or plug in that allows for "squiggly" lines? The line/ curve tool seems to be limited to 4 points that act as reference points for curves only so it isn't any use to me.
View 5 Replies View RelatedI'm trying to draw a plan of my house in Autocad 2009 but I seem to be endlessly using trim and extend because I can't easily select the points that I want with osnap. Eg. imagine I have a box, and I want to start drawing another box inside it that has each side as 10 units smaller than the corresponding side on the outer box.
Step 1 - I draw a small line from the top left corner of the big box using the endpoint snap, typing in "5" for the length.
Step 2 - I then do the same at right angles to the first line to get me to the starting point of the inner box. This always leaves me with 2 small lines to remember to delete.
Step 3 - Then in order to draw the top line of the inner box I end up drawing to a random length because I can't say "draw until 5 units away from the right hand side of the big box", then I end up trimming it later once I've repeated steps 1,2 and 3 for the next side of the inner box.
I know in my example above I could have scaled the box down or something but that's not what I'm getting at. I really want a way of selecting line start and end points that are a known position away from an existing point.
Im still new to Civil 3D and i would like to know how to connect inported points using 3D polylines. I imported my points from Excel in a PNEZD format. How do i get the 3d poly line to snap to my points so I can Connect them? someone mentioned using a feature line to connect the points but im not sure how or what that would do.
View 3 Replies View RelatedI am working on a utility map with water valves and hydrants. I collected my points with a Trimble unit and converted them to shape files. I am unable to snap to these points, how i can use snap to draw my water mains from point to point?
View 5 Replies View RelatedWith all of you fine teachers, I have the know-how to get the start and end values of a line.
Do you think there is a way to get a point returned that represents the true intersection of the two lines, without having to involke a user defined "getpoint" function using "intersect" osnap?
I tried to set Polyline.StartPoint to new position (Point3d):
Polyline.StartPoint = myNewPoint3d;
I have "not implemented" exception.
Also, I tried to do it as:
var seg0 = acEnt.GetLineSegmentAt(0);
seg0.Set(newPoint3d(0, 0, 0), seg0.EndPoint);
It doesn't work also. I can do it as:
acEnt.SetPointAt(0, my2dPoint);
But it's 2D point, not 3d
Of course I can remove polyline and create it again, but. How to set start point correctly for 3d point?
I draw a pline. It asks me for the start point. I type in INT. I used to get this 'x' when I was near the intersection. That is now gone. It will still go to the intersection, but I really want my 'x' back.
View 9 Replies View Related[Managed ObjectARX 2007 with C#]
I am trying to create an arc with start point, end point, and radius. So that if the arc gets drawn, I going to use the center point.
Well, I guess I can use "SendStringToExecute()" or "SendCommand()" and "ObjectAppended" event handler to get the arc object.
C3D 2010..I have a alignemnt that I need to move the starting point 120' east of where it is now.
I've treid a slew of thing to no avail. Can this be easily done?I already have existing profiles for the current alignment.
I draw 3 lines to form an open polyline. They are still in lines, not converted into a polyline.
How do I find the start or end point of the polyline with program? I am thinking to check all points which is not shared by two lines.
how do I retrieve the centre point in my design axis in Inventor, when I create a new sketch, like the point at x0:y0:z0
View 2 Replies View RelatedI have a problem with absolute and relative coordinate regarding drawing an arc.
From my previous studies, I thought whenever I input coordinates in command line, in order to use absolute coordinates I just enter them. If I want to use relative coord, then I can prefix them with @ sign.
For an arc I input as follows: start point: 0,0 2nd point: 500,500 end point: 1000,0. I was expecting to get a half circle from origin to 1000,0 point but to my surprise I find out that CAD gets the input coordinates as relative.
Am I missing something? 1.dwg1.jpg Is this behavior same for all other object drawings?
Before when I was creating models the origin (0,0,0) was always set in the snap point i started the line in. Now suddenly something happend and now 0,0,0 is always starting in the Original XYZ point.
How do I get back to the old settings?
Using Lisp or VLisp, how can I find the Start & End Point of an AEC_WALL ent. ?
View 5 Replies View RelatedI'm having a problem, How can I draw a circle which has to go through point & tangent, if I know radius?
View 4 Replies View RelatedI need to draw an arc that starts at a specific point, ends tangent to another line, and has a specified radius. What's the best way to do this?
View 3 Replies View RelatedHow to draw an arc tangent to a circle and a point. The attachment here is a detail of the problem I'm having. No 9
View 3 Replies View RelatedWhen trying to draw a line and choose a starting point, autocad decides that this is wrong and start the line in a different place. I've turned of autosnap and autotrack but this dosen't work.
What is it that I've forgot to turn off?
How to draw a line perpendicular on an arc at the a particular point?
I wanted to draw a line perpendicular to an arc at a particular point but couldn’t approach it. In this case, I need two snaps to work at the same time! To be perpendicular on the curve and at the same time to be snapped to the point!
How do I draw perpendicular from a line or object at a specific point? I know by holding shift and osnap perpendicular I can draw the line but I can not osnap to the exact point!
View 9 Replies View RelatedI created a linetype using text shape. Let’s say, that my line is only AAAAAA. Now when I apply this linetype in the drawing, the lines always have a small, line before and after the characters. Actually you see this: -AAAA- . How can I delete or hide the start and end lines.
View 2 Replies View RelatedHaving used another CAD program for several years, I was used to the idea that all radius dimensions, like of a given arc, would easily start at the center of the arc, thereby denoting the position of the arc's center.
I'm slightly bugged with some CAD users, even books on the subject by autocad users, that give an arc's dimension from the outside of the arc, yet fail to show the location of the arc's center when it may not be self explanatory. Not good dimensioning practice from what little I've been schooled...
So, in AutoCAD 2007, how do I get an arc's radius dimension line to start at the center and point out to the edge. I can do all kinds of things to the position of the text, etc, but can't figure how to get it to start at the center. (The dimension line needs to start at the center.)
I wrote some stand+alone application (WinForm=, where user can specify dimensions.Now after button click I want to switch form to current AutoCAD file and prompt user to specify point.
From this point I want to start drawing few lines.And I don't know how to switch to AutoCad and get current drawing space.
Drawing Parrallel lines from one elipse to another?
I am drawing pipe and beams.
I use a variety of methods. Right now I just SNAP to the elipse, draw the lines at the angles and then hit the other elipse. Sometimes though the lines jump all around the elipse.
I am trying to draw lines(orange colored) on this 3d object(crimson colored). Every time I go to select the lines to alter them I end up only being able to select the 3d object they are on. How do I turn off the selection of the 3d objects or anything on that layer?
View 9 Replies View RelatedSomehow i can't draw lines with different lineweight. I can change the color and the linetype but the lineweight doesn't. In the properties toolbar over the workspace the last option (after lineweight) is not active and shows bycolor!I suppose that is the problem why i can't draw lines with different lineweight!
View 9 Replies View RelatedHow can I draw lines with numbers in autocad that represents sizes of other lines (I don't know how to call them on English) ? For example on this pic lines with numbers 50, 60, etc.
kotiranje1ab1.jpg