I haven't used Autodesk directly since Land Development 2i. I remeber being able to draw lines by distances and bearings with the numeric keypad. The bearing quadrant / DMS input was a fast way to draw parcels from an existing map. When I got to a curve, I remember being able to input radius and Delta angle. I've been trying to find those functions for months now. I found the Line by Bearing command and that works well as long as I don't run into a curve.
How do you draw a curve that's tangent to the previous line with the radius and delta angle? I've been going back to AutoCAD version 12 methods. That is, offset the previous line. draw a circle from the end of the offset. draw a line between the center of the curve and the end of the previous line. Rotate that line with the 12d34'56" format. trim the curve and erase the extra lines.
I've gone through all the curve drawing options in the home menu.I found the CoGo editor in the survey menu but it doesn't draw curves. It just draws a line from the beginning of the curve to the center and continues the traverse from the radius point of the curve. That's obviously either a serious misunderstanding of input or a program bug.
I am trying to draw a parcel map using AutoCAD MAP 3D, using distances and bearings that were added by to the original hand-made drawing by the surveyor. The parcels don't quite close perfectly... what the acceptable tolerances are for parcels of say 1 acre and under, 1-5 acres, and 5-20 acre sites?
I'm working with site plans and have a lot of distances and bearings in my drawing.
Sometimes i need to reverse them. Is there a command in AutoCAD 2012 where you can reverse a hole heap of distances and bearings all at once? Mirror make them up side down. I want them to swop sides of the line they refer to.
I draw property plats for a surveyor and looking for a way to add the bearings (for example: N 56 15' 32" E) along the property lines. Right now, I use the Distance command to find out the bearing, write it down, and then add it to the aligned linear dimension text. I'm guessing there's a faster way to get a bearing along with the distance without typing it in.
I am using AutoCad C3D. I have drawn a building and now I am trying to position the building on a plot with uneven property lines using only “tie distances” from the spots on the property to specific spots of the building.
I do not know which C3D program functions (with just distances known) to get the building placed properly on the plot.
Im still new to Civil 3D and i would like to know how to connect inported points using 3D polylines. I imported my points from Excel in a PNEZD format. How do i get the 3d poly line to snap to my points so I can Connect them? someone mentioned using a feature line to connect the points but im not sure how or what that would do.
I have to draw hundreds of lines that have same start point. How can i do this?
I am trying to insert a picture but seem impossible for me. Sow i have lines with the same start point and different endpoints. There is a short way to do this. so avoid to enter the same start point for hundreds times or snap the the same point infinitely... what about Copy with grips or Change command in this case?
I have tried unsuccessfully to draw lines using bearings as a surveyor draws them. I have seen a number of posts here and on the web, but they relate to northern and easting’s, but as you can see on the attached PDF from a surveyor they have used only bearings. I’m not a surveyor, my background is mechanical so this is all new to me. what units and settings I may need to change in order to draw using these bearings. I’m using Autocad 2012, and the attached PDF relates to some blocks of land in Australia (just in case that makes a difference in the settings)
I need to be able to draw "squiggly" (multi-point)lines. Specifically, roads on a map. Is there any tool or plug in that allows for "squiggly" lines? The line/ curve tool seems to be limited to 4 points that act as reference points for curves only so it isn't any use to me.
I'm literaly just starting to use CAD so this might be a silly question, but how would I offset a line more than one distance in a command? Is there like a symbol you put between each distance like 2000;2250;2650 or something along those lines (no pun intended).
How do I draw 2D lines from points? What setting do I need to change? I want to drawin glines using the node as a grip but I do not want them to have z coordinates.
Any way to add a (R) to the Bearing dislpay, to indicate a radial bearing, in a Line Table?? This would only apply to certain lines, not all of them. I can specify which line. That function does not need to be automatic.
I am working on a utility map with water valves and hydrants. I collected my points with a Trimble unit and converted them to shape files. I am unable to snap to these points, how i can use snap to draw my water mains from point to point?
Is there anyway to prevent a corridor from jumping across large distances as in the attached screen shot? There are no targets in any of these regions.
I've got a closed traverse that has all the elements, but when I try and analyze it, I get the dreaded error: Insufficient angles, distances or points to calculate this loop. Creating a Traverse for Adjustment: [URL]l and my screen capture looks very similar to his, but I'm not getting any results.
When trying to draw a line and choose a starting point, autocad decides that this is wrong and start the line in a different place. I've turned of autosnap and autotrack but this dosen't work.
How to draw a line perpendicular on an arc at the a particular point?
I wanted to draw a line perpendicular to an arc at a particular point but couldn’t approach it. In this case, I need two snaps to work at the same time! To be perpendicular on the curve and at the same time to be snapped to the point!
How do I draw perpendicular from a line or object at a specific point? I know by holding shift and osnap perpendicular I can draw the line but I can not osnap to the exact point!
I wrote some stand+alone application (WinForm=, where user can specify dimensions.Now after button click I want to switch form to current AutoCAD file and prompt user to specify point.
From this point I want to start drawing few lines.And I don't know how to switch to AutoCad and get current drawing space.
Drawing Parrallel lines from one elipse to another?
I am drawing pipe and beams.
I use a variety of methods. Right now I just SNAP to the elipse, draw the lines at the angles and then hit the other elipse. Sometimes though the lines jump all around the elipse.
I am trying to draw lines(orange colored) on this 3d object(crimson colored). Every time I go to select the lines to alter them I end up only being able to select the 3d object they are on. How do I turn off the selection of the 3d objects or anything on that layer?
Somehow i can't draw lines with different lineweight. I can change the color and the linetype but the lineweight doesn't. In the properties toolbar over the workspace the last option (after lineweight) is not active and shows bycolor!I suppose that is the problem why i can't draw lines with different lineweight!
How can I draw lines with numbers in autocad that represents sizes of other lines (I don't know how to call them on English) ? For example on this pic lines with numbers 50, 60, etc.
How do we draw three lines instead on one? As an architect, the exterior walls are 3-lines for brick construction. How can I draw with 3-lines instead of one in Aouto Cad 13 for Mac?
