I have multiple copies of a block, and when I move one copy to a layer, it doesn't seem to actually move.
For example, if I have 2 copies of block A, and move one copy from layer "Inside" to layer "Outside", then hide layer "Outside", the block I just moved doesn't hide, but everything else on layer "Outside" does hide.
When I inspect the moved block, the properties say it's on layer "Outside". What is going on?
I have a block containing a visibility parameter but the problem is when it is inserted, that visibility parameter is in a different place to where I put it in the block editor.
My geometry is around the 0,0 origin (which is also the base) and the visibility parameter was placed at 0,-25 in the block editor however once it is inserted in a drawing it shows up at 270,130.
No matter where I move it back to, it always reverts back to another position. Every time I try to change and reinsert, I purge the drawing so I know it is not picking up on something else.
I just have a quick question (hopefully) about an activity I want a Dynamic block to perform.
I have a simple electric switch block (a line with an S over it), that in some cases is enclosed by a simple rectangle. When the switch is enclosed, I'd like the attribute to move further, to keep the spacing the same.
Is there a way to make the attribute move automatically with the display of the rectangle, maybe through some combination of Linear Move parameters, Visibility parameters, and a formula?
I took the time to search and was unable to find anything that seemed relevant. I have also had trouble figuring out the documentation.
Is there a way to select a specific grip within a dynamic block and then update its position?
My company just upgraded to 2013 from 2012, and we are having problems copying and moving dynamic blocks. As we try to re-insert the object(s) after using the copy or move command, they disappear from the screen. If we save the drawing and restart AutoCAD, the objects are there where we inserted them, but we cannot figure out how to make the objects reappear without restarting the program (Undo does not work).
The objects in question are dynamic blocks created with AutoCAD Civil3D 2012. We suspect this might have something to do with conflicts between the two different versions of AutoCAD but we're not sure. There are 5 or 6 of us who have this problem.
Currently, I have the base or insertion point of some of my blocks in an undesirable spot and I would like to move it. When I insert a drawing or block I have difficulty in placement due to a poor choice in the drawing or block I am trying to insert.
View 6 Replies View RelatedI have recently started to have a problem with lines, leaders, blocks and x-refs etc, straying from level 0 for z. I think it may have something to do with the fact I am making use of files from cad duct 3d software, how do I prevent/resolve this?
View 3 Replies View RelatedThe linear stretch works fine but changing the length affects the position of the tick marks of the polar stretch. If I change the degrees to 0-360 then it's not a problem but I want to restrict to 285-345 deg.
I can't figure out how to move the base angle of the polar stretch with the linear stretch.
In "test" mode, this block works well except for the point of the arrow. If you stretch the line under the title, then move the arrow point to somewhere else, then flip it, the arrow point and its associated grip needs to stay put.
It actually does, the first time. BUT then if you move the arrow point again and flip it again, it does not.
Then, when I inserted it into another drawing, either with "insert" or via SSM, the flip doesn't stick to the point even the first time.
So I guess my question is how to flip it but keep the point where it happens to be when the flip occurs. Like a multileader, because what I am actually trying to create here is a multileader that has an annotative block with attribute fields, to be used with SSM.
I have two .dwg files. One file has every layer that I could possible need on it. The other file is an existing file created in my office. So, I want to take an existing drawing that does not have a good layer naming system and move it into the file that does. I saw in another post that this can be done in the Design Center, however when I go to copy layers from the existing file to the destination file it won't let me. Does this make any sense?
View 2 Replies View RelatedI'm using imported blocks in my layers. I use the same layer with two maps but they do not print the same.
View 2 Replies View RelatedInputting bearing N5 degree27'23"W autocad 2010
View 8 Replies View RelatedI was wondering if there is a way to import a bunch of detail drawings into my template, without all the layers that go along with the details.
See, sometimes I need to use details from other companies within my drawings, and they have crazy annotations and a lot of different layers. It would be nice if I could import their details as one big block into my template that I like to work with when doing my work. Is there a way that I can import that details block (including its color codings and such, not changing anything) onto ONE LAYER. Otherwise is there a way to create like a folder within the layer manager that I can dump all those layers?
It's just such a mess once I drop their details into my work, it would be nice if I could isolate all that stuff, yet keep everything as it looks on their files..
I have a piece of machinery with a platform around it. Right now, I have it set up where, you bring in the block on a -proposed layer, and then you can change it to a -existing layer, and everything changes to that new layer's colors (elements on 0 and bylayer).
However, what I would like to have happen is, inside that same block, I would like for the platform to change from a different color to a different color when the machine does.
So... the entire block (machine + platform) is on a layer - machine-pro. I bring it in, and everything is blue (for proposed). When I switch it to the machine-existing layer, it changes to a dark blue. I know I can have the platform be red and the machine blue, but when I switch the machine over to the existing (dark blue) the platform would still be red (because its set as a "hard" color other than by layer).
Is there a way to make the platform turn to a dark red (existing) from the bright red (proposed) when the machine turns to a dark blue (existing) from bright blue (proposed), but it all be in one block?
How do I create a new .dwg that has no layers, blocks, text styles and dim styles? 2013 Civil 3D
View 3 Replies View RelatedI have been working for a new company who likes to use blocks extensively. My question is this, is it possible to quickly change the layer of the components of a block? That is, the lines, arcs, etc of the block. Or, is the only way to explode the block, change the layer and remake the block?
View 2 Replies View RelatedI'm doing very complex drawing of a heating plant on a big ware house site. So I'm using two kinds of layers. I don't know, weather I'm using everything how it is to use or not, because I learned everything by myself.
The first layers are my so called "line type layers": hidden line, center line, wall, border, ... So all the different types of lines I'm using, when is start my drawing. I block all lines, which belong to one part like screws, doors, pips, engines, .. And at the end I put my "part" blocks" on my "part layers", like deashing, ash bin, boiler, building, electrical.
So lets say I have the layer "deashing", which includes several blocks like "deashing screw", "deashing drive", "deashing screw 2", .. And each block consists of several lines, which are on the layers, like "hidden line", "center line" and "black thin line", ...
And now I want to switch of everything in my drawing, which belongs to the "deashing layer" to get a better overview. So I "turn off" the layer "deashing", but I can still see it in my drawing. It just disappears, when I freeze the layer, but it should disappear, when I "turn off" the layer, too, shouldn't it?
So I hope I didn't wrote to much, but I good explanation is worth everything. So why does it not disappear or do I use the layers in a wrong way.
When I bring a part in as a block into an assembly, is there a way to turn the block of just that part off and all its layers inside that block?
View 4 Replies View RelatedWhen inserting certain blocks that were created in the 0 layer, they are not taking on the color of the layer in which I insert them.
Now when I click on the object, it shows up as being on the correct layer but the object is still white, I ran into something like this before, and was able to fix it by going into the Block Editor and setting the layer in there. This only happens on certain blocks.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
After all this time is there a way to assign layers to different objects with a block? Perhaps using Visibility states or Lookups?
As an example:
I have a dynamic block with a door swing and text. As I increase the size of the door the text changes to reflect door size. The objects are all on the 0 Layer. When I insert the block I can assign a 'Text A' Layer to the text and a 'Door A' layer to the door. So when I switch layer states around I will either see the door, the text or both. Then I move to the second floor which has been stacked on the first floor. I insert my DB and assign layers 'Text B' and 'Door B' respectively to the text and door.
Finally when I go to my layer states I either select 'First Floor' or 'Second Floor' and the respective blocks appear depending on the layer state.
We have blocks of process valves. The valve body in layer "valve" and the ports in layer "pipe" The Lower port of the valve is for "fluid A", the upper port for "fluid B".
Now we want to dynamically choose the layers for both the lower port and (a different layer for) the upper port. Dynamically because the same valve can be used twice with completely different fluids / layers. Is there an attribute or dynamic parameter to do this?
I made a dynamic block with attributes. The block was to be moved using Linear parameter + move action, and then a lookup parameter and action.
The block moves as it is suppose to but the attributes are left behind. How can I get the attributes to move with the dynamic block?
The attribute properties are:
Verify = Yes.
Lock position: Yes or No don't seem to make a difference.
Is this a bug in AutoCAD or is there a solution to this?
In the past two weeks I've noticed a weird problem with my Photoshop CS5. I'm on Windows 7 64-bit with CS5 version 12.0.4 X64.
Sometimes (not always) when I click a layer in the layer menu and try to move it with the move tool, it jumps to a different layer (not to the one I selected) and moves that one instead. Now, this is only if I move it with my mouse. If I move it with the keyboard, it works fine.
Also, if it starts doing this with a layer, it will continue to do it with that layer forevermore. Even when I close the program and re-open it again. Or if I save it as a diffeent filename. If I duplicate the layer, it will do it on both the original layer I was having trouble with and the new copy of that layer. I can also merge it down with a blank layer and it'll retain the problem in the new, merged layer.
It's annoying to have to move the affected layers with the arrow key.
I did find a mention of this problem on a mac, but the solution did not seem to apply to a PC.
I'm having an issue with Photoshop crashing when I move layers up or down. I'm using a macbook with lion.
View 2 Replies View RelatedI'm trying to make a sig for a message board. What i have done. removed background from 4 different photos using erase tool in cs4. So in one psd i got 2 b-ball players with the bg gone then. In 2 other psd i have one b=ball player with backgrounds removed Now I want to take all that and put it together in a new background.
View 2 Replies View RelatedAs I click on a different layer in the image window, the cursor seems to grab what I want without even going to the palette to select what I want! Not even having to right click. But I'm not sure if this is consistent,
View 2 Replies View RelatedAre there any official document describe the limits in a DWG file? For example, the maximum number of blocks that can be added, the maximum number of layers, the maximum length of an object name, etc.?
View 2 Replies View RelatedI’m currently working on getting a system for easier plant layout management. Part of which is condensing what started as 195 mostly random layers into about 15 usable layers.
Problem:
I have about 28 more layers that need to get rid of and I can’t delete them because there are lines assigned to them. However, when I hide all the layers I need so that only the unnecessary layers are showing, there’s nothing there.
Side Note:
I know this problem is most likely because there were layers applied to features deep within blocks. I just don’t want to go through the 700+ block to check each layer assigned to each line.
(This file I was given to start with is a mess. Examples: Some of the blocks have the same exact feature that’s buried 7 blocks deep with no features added to justify an extra bock being there. Some of the blocks aren’t even being used in the layout. Name of the block has no coloration with the actual thing it represents. Stuff like that…)
Question:
Is there a way of hunting down these layers in the blocks to delete / change them without checking each individual block? Or is it possibly because the layer i need to get rid of is applied to a block that’s not being used in the layout?
I was able to write a LISP that replaced each node with a block of my choice.However, now I need to find a way now to replace the blocks with different blocks.Each point shares the exact same block called "PILE". Different blocks are on different layers and have 11 different colors. I'd like to replace blocks on layer 1 with a block called "1" and blocks on layer 2 with a block called "2" and so on.I was hoping there would be an easy way to do this in LISP, but I've been unable to get any of my scripts to work.
I've attached a link that visualize what my drawing is currently looking like: [URL] ......
The routine below delete group of blocks by name, but if the blocks are on locked layers, these are not removed.
How can improve the lisp?
(defun c:deleteblock (/ rn ss)(defun Jd (realname) (setq ss (ssget "x" (list '(0 . "INSERT")(cons 2 (strcat "`*U*," REALNAME))))) (mapcar '(lambda (x) (if (not (eq REALNAME (vla-get-effectivename (vlax-ename->vla-object (cadr x))))) (ssdel (cadr x) ss))) (ssnamex ss))(setq ss_len (sslength ss)) (command "_erase" ss "") ) (setq rn (vla-get-effectivename (vlax-ename->vla-object (car (entsel "
Select the block you want to delete:"))))) (jd rn) (princ (strcat "
" (itoa ss_len) " Blocks called "" rn "" has been deleted")) (princ) )