How I would draw a simple plate transition? It would be 3' - 6 1/4" OD at the top and 10' - 6 7/8" OD at the bottom. It would be 62" tall. I draw this but can't figure out how to make it "flat" like a layout on a piece of plate to cut out and then form / roll into into it's final shape. I looked at one of our past project's drawings and it shows this, but looking at the dimensions on it, I cannot figure out how it was done.
View 9 Replies
I'm trying to draw a helical staircase with a bottom plate underneath the steps. Drawing it isn't a problem. I used a sweep with helical curve. Then I converted this part to a sheet metal. But then inventor doesn't want to unfold it. how I have to make a flat pattern from this one with the necessary bending lines?
Example .ipt and photo in attachment
I have attached a pic of what I am trying to accomplish.
The part was done in SW, but I am now needing to do it in Inventor.
I have a flat plate, 12" square, that I am needing to bend the 2 corners up, with 10 1/2" between bend lines.
I tried using the "BEND PART", but I can only select one line. What should I use so I can bend all four sides up?
Lenovo Think Pad
Windows 7 SP 1
64 Bit.
Inventor 2013
ACAD Mechanical 2013
I have a face plate with strokes on it to represent pressure increments.I cannot get the numbers onto the face plate.On the large stroke it starts at 0 and goes to 9 .. How do i add the numbers. Also i used extrusions for the increment strokes with circular patterns and mirror features.Is this how it should be modeled?
2013 EDU
is it possable to add an opening into a plate created in Plant3D?
i.e. i have some equipment that need to pass through the grating of several leveals of a new structure.
I seem to have made what many might consider a rookie mistake. Built a fairly complex structure for an overhead crane system and get to the end to find that I missed two holes. The problem with these two holes is it is ONLY 1 plate (my grounded part), but I have used this same part in one other instance. So if I edit (even from within assembly) and add the two holes to the grounded plate it creates them in the other plate, which I dont want.
Since I have the second plate being used as a refence to locate MANY other parts on this unit, it would be quite difficult to replace it with a new part (same but different file name).
Any way to add said two holes to the grounded plate only and not the other?
Inventor 2014 PDS
If you have a steel plate bent in several directions and with non-perpendicular ends, designed in 3D Auto Cad.
For example, the plate can be curved with a certain radius in the vertical direction and another horizontally. How would you, or what software would you use, to get the plate flattened to the exact measurements of how it should be cut.
Basically we are trying to make a 3D plate (in this case a 2" thick piece of steel) and have a 3D hollow shape inside. Its split into Top and bottom, as shown as the below picture.
top View (plate 1).jpg
I have tried the loft command (which I just learned off within the past hour or so) and it indeed works. But I wish to use its as the opposite, where the middle is hollow and the rest is a solid object.
Side View (plate 1).jpg
I have tried the loft command (which I just learned off within the past hour or so) and it indeed works. But for the life of me does not know how to get it as one big object with the middle shape hollow. Am i missing a step or is it another command completely?
Also, once the object has been created, I want to split the object on its X axis mulitple times, almost like an exploded view. Each split will have its own set of top and bottom orifices which will represent multiple plates.
Is there a way to do that? Also is there a way to gain and separate the top and bottoms of these newly split plates?
Here is the drawing file as well to work on -> 3D-MK1.dwg
I'm modeling a band that will be screwed onto the inside of a sheet metal cylinder. The band will be rolled to the ID of the cylinder. I'm trying to model the holes in the band, and place screws into the holes. I'm not sure yet how the holes will be machined out in the shop--whether they'll be drilled or punched, made before or after the band is rolled, placed based upon degree or arc length, etc.
1. Is there a better way to model the band and its holes?
2. How can I properly and easily insert the bolt into the holes since they're no longer "perfect holes" that can be used in an "Insert" constraint.
3. How can I then pattern the bolt so I don't have to insert one into each hole?
I have attached a jpeg file of a Plate out of a heat exchange.It shows half of the Plate but it is identical shape for top and bottom.I am able to create the solid shape but i need creating the numerous patterns onto the plate.How would i place the pattern feature onto the Plate?
Also from the picture there is a gasket.Would this be made as a separate part and placed on the Plate in a assembly file?Would the gasket be best made using sweep function?
I have created the plate as a solid model but would Sheet Metal also work or even be a better choice?
Inventor 2012
I have an oddly shaped flat plate extruded from a sketch, the sketch of which has lots on constructions lines, none of which actually represent solid edges of the plate. However, I want to locate the plate to other components via the geometry defined in the sketch.
I find that when I am trying to constrain the plate to other parts none of the sketch geometry is available to me. Points, lines, construction lines, circles; I can select none of it when constraining. I am confused. How can I constrain such a part?
Just to clarify - the flat plate is the base of a structure. Its profile is decoratively shaped, so nothing about the cut edge of the plate is suitable for constraining to. I need to constrain off geometry defined in the sketch.
I have "Shared" the sketch.
Inventor 2013
I want to form a plate (collar palte around branch (riser) connection, which when is flatened the projected circle will be eliptical. Before Refold I want to cut plugholes for welding. In flat position it looks like a flange /w holes and the middle cut-out is elliptical. I want to refold it to be again in rolled shape.
My system has Inventor Professional 2013.
I have been trying to fold a round plate which has 10 milimeters thickness.Is there any way to fold this or unfold ?
View 4 Replies View RelatedHow to create a switch plate dynamic block. I can draw the light switch inside block editor no problem. My Objective: To insert a single light switch plate block into a drawing and have the ability to stretch the block to increase the number of switches from 1 to as many as 10 in a gang style. The light switch box would do a basic stretch, but I just can't figure out how to increase the number of switches as the block increases in width.
View 2 Replies View RelatedHow to modify handrail to remove the kick plate in attached sample.
View 1 Replies View RelatedTexture map that will simulate checker plate and industrial steel grating? This would be for Inventor 2013.
View 4 Replies View RelatedAny way to show clearly that there are counter bores on both sides of a plate. It does show the dotted lines for when it is on the down side of the plate, but in some sections i have a counter bore of the same diameter on both sides of the plate. Is my best bet just to to create two drawings of the upper and lower faces?
Also i've been trying to use the hole tables, something thats new to me, and i can get all the holes coming up, but im unable to get them to show up as actual counter bores, instead it shows up as two entries.
I am trying to learn how to carry out stress analysis within inventor and have applied what seemed logical to me, however when I got my results file it does not seem to add up.
I want to investigate the effect that a crack will have on a piece of steel plate, I have applied a fixed constraint to one side of the plate, and a load to the other side, as well as a separation contact on the sides of the crack (see file attached).
I need to create the crimp plate in inventor to give my shop the measurements before the crimping process for material and also give them measurements to complete the crimping process. I figured I could use the sheet metal process. I'm trying to find an easier way than going back to Autocad and p-line everything.
View 6 Replies View RelatedI have just created a cylindrical object with an extrusion length of 300 mm and then created an assy(.iam). On to this cylinder i have placed a plate at right angles to the axis of the cylinder
What i wish to do now is mirror this plate.
It would appear the best way would be to create a work plane(mirror plane) thro the centre
Of the cylinder,however, how can this be done if when requested to create the plane 3 points are required,am i missing something here.
Doing a bend on diamond plate. I have applied a texture map to the side of the plate that has the diamond pattern. When the pattern gets in the corners (inside or outside), the texture map shifts. When it does this, the diamond pattern does not look the way the real part will. Below is an image of what I am seeing.
View 6 Replies View RelatedI have drawn a cylinder, with inside diameter 1028mm, wall thickness 5mm. We usually have calculated unfolded part length like this: outside dim. 1038mm - 5mm (wall thickness) = 1032 x 3,14 = 3240mm. Now when i unfold in inventor I get for the length 3215,35mm. It is quite far from the result we usually would have received.
Unfolded part will be rolled to cylinder. What parameters should be overlooked when making unfolded parts for plate rolling?
I could not find Round Perforated Plate style / appearance on Autodesk Inventor 2013. Maybe it called "Perforated Metal 01 style" on previous Autodek Inventor version.
I just found Oblong Perforated Plate as attached.
Looking for 2012 sheet metal template with all the common plate sizes already in the rule?
View 6 Replies View RelatedI have created a Hollow Cylinder using Polysoild (Object Option). I want to drill holes(array) on the cylinder.
View 9 Replies View RelatedHow do you most easily do a sheet metal plate that needs to follow a surface?
L1 is less than L2, and a radius of the plate?
In Inventor 2012
I have been working on a large assembly and I am trying to get a bolted connection to pass through a component and a machined plate. I have been using the cocentric option to complete many other holes up to this point, but not through a machined surface.
When I attempt this, I get two errors saying:
Design Accelerator Doctor
1. Failed to add sketch for a hole
2. Failed to create a hole
My questions are:
Is there a way around this Or is this a problem that I am going to have to work around?
Or
Is there a better way to get a hole/bolt through this assembly?
I have a sheet metal part I need to show as polished aluminum diamond plate on one side of the material only, just as it would appear on the actual part.
Inventor 2013
Designing a tailing dam I use a corridor model witch changing slope grade from 1:2 to 1:2.5.
There are assemblies and subassemblies with shapes defined for each slope grade, but how do I make the transition from one slope grade to another on?
In corridor properties I included two regions for each slope grade.
For grading there is a transition function. But the transition for corridor?
I have a sequence of low quality images that captured by a regular shop camera. I wanna identify license plate of the car in images. I am wondering if it is possible to use the sequences to zoom in the image and identify the license plate? 15 images of the sequence are uploaded, if more are needed, i'll upload more:
[URL]...........
I was looking for some background images of diamond plate for a background to my website. If anyone knows were some cool backgrounds for this is, please let me know.
View 1 Replies View Related
