since my new pc Civil 3D does not open with my profile that i have created when i still had my older pc , i used that profile for quite some time in civil 3D on my previous pc , but with my new pc i have to open Civil 3D and load my profile manually every time i open the program.
i have found a solution where you can add the profile saved path in the short cut which you use to open the program with.
i have tried that but i get an error saying i don't have admin rights.
which is very strange cause i have full rights on my machine and the IT guy has confirmed that.
I have an alignment label that I normally use to show the PVI's of a profile in the plan view.
This is a little unusual, but in a specific case I wanted to design my profile at one alignment, but show it at another. I designed my swale profile in the pathway profile view and then superimposed the swale profile on the swale profile view. I then went back to the swale alignment to add these labels.
It's a no-go AFAICT. The only profile available for me to select for these labels is the original ground profile from the surface.
I'm working with a structure profile label style and it seems like the only way to anchor the position of the label is based on offsets from the structure itself... Any way to position the label based on the top of the profile view, so that I could make all of my labels horizontally aligned above the profile view?
Im creating a Profile Bandset and would like to have multiple surface/profile elevations shown, ie: EG, FG, Back of Curb and Back of walk. While creating this bandset I see that the text component editor properties only has code for profile 1 elevation and profile 2 elevation in the properties area, which the code for this looks like below.
Ive tried to write my own code using the profile 2 as an example but it doesnt seem to work as a 3rd surface/profile and only seems to mimic the profile 2 elevation when placed in the band
My questions are as follows
1) does Civil 3d only allow 2 surface elevations in any band set? if it does allow more profiles/surface elevations what am i missing to create it?
2) if Civil 3d does alow for multiple surfaces to be shown in the band set how do i get the text component editor to supply the extra profile elevation codes? or would i need to create from scratch
3) if i need to write the code from scratch does any listing of the codes and meanings of each code ie what does RN, Uft, Sn and so forth do and mean .
I have a group of profiles in a drawing and I want to change how one of the profiles is displayed through the profile view style manager, but I do not want to change how all of the profiles look. Is there a way to change the way a single profile looks without changing all of them?
I have a profile showing proposed storm sewer, existing sanitary, rock surface, existing surface, and proposed profile. Today for some reason the proposed profile and labels, and the existing surface are not showing on the profile and I'm not sure what has changed or how to get them back.
I am working C3D 2012. I have a proposed alignment and profile design by another firm that I had to tranfer into C3D. I had no problem getting the horizontal alignment to display from a text file. I tried to do the same with the profile by using the 'create a text file and create the profile from file' command. I got the POB, PI's, and POE to display. I then defined the VC. I wanted to verifiy that the profile was indeed accurate compared to what we were provided. So I tried to execute a profile report PVI Station and Curve Report - I keep getting an error that "No FG profiles in dwg".
I know the Proposed profile is indeed set to proposed in the properties. I have noticed that the icon next to the profile I create from the text file is different than the profiles created from scratch.
Is there a way to convert this profile to be recognized as a FG profile?
The intersection wizard makes dynamic EOP profiles based off of the cross slope from the centerline. Well the intersection tool doesn't always work with funky intersection layouts. Is it possible to manually create a dynamic EOP profile based on the cross slope from the centerline profile?
I have yet to produce a profile. I created a polyline and turned it into an alignment.
Looking at alignment Sample(3), I see that it is not superimposed over your surface. The polylines are, but the alignment is not. That will disallow creation of a surface profile.
Is the sample5 an alignment that sits on the surface? how come there is still no profile?
differences in elevations of points along Profile 2 (the proposed new road elevation) and Profile 1 (the existing elevation/surface) should be computed and shown right above the Profile 2 line. For example, if at a certain point PT 1 the elevation of the proposed road is 132.44 meters and the elevation of the existing surface is 132.45 meters, the difference is -0.01 meters and it should be shown exactly above the Profile 2 line (or a little bit above it) but not on it. The same should be done for every chosen point along the proposed profile.
So far, I have done this manually, by dragging the difference (already automatically computed and shown in one of the bands below the profiles) to the correct place for every single point. However, I don't know how to do this automatically.
We have an engineer who is taking an existing surface and wants to show a proposed road 2" higher than existing.
I told him to simply adjust his assembly for his corridor to account for the 2" difference, but the County agency needs to see a profile.
My questions:
1) Is there a way to easily copy a profile made from a surface and "convert" it to a proposed profile? If we copy and explode, it turns into hundreds (thousands?) of tiny pline segments and it would be a mess to convert all those to a profile 1 by 1. If we make the corridor, and choose "profile from corridor", we do not have an option that could be used to represent the centerline.
2) Other than loss of dynamic updating), would it make sense to adjust the assembly so the top surface would be accurate, then copy the profile, explode the copy to a block and simply shift that (as essentially basic linework)?
where to change the text height and color for the lower band where the stations are. Also, how do I get the exist grade and proposed grade to show at the specified stations vertically like LDD used to do it.
Second, how do i mask the pipe in the manholes on the profile. Right now i can see the pipe inside the manhole. I clicked "enable masking" under the structure properties but no luck.
Attached are survey points that created the surface of a road embankment portion that caved-in. The road is very near a reservoir shoreline.
1. How can a surface profile be produce? I/'ve use line to change it into an alignement and then create a proile , then a profile view. But the the surface profile is missing.
2.the points having higher elevation are the top edge( road level) of the cave-n . A few few shots were take before the shorline elevations.
3. What the best way to come up with the rock volume to fill the cave-in given this surveying points., Also the shoreline elevation will be lowered some more while work is being done since the fill is not allowed to fall in the reservoir.
I have 3 profiles that I've superimposed together. Then I created sheets using the superimposed profile. I used the wizard and had Civil 3d do it for me (2012). Now I have to add a 4th profile to the mix and get it to show in my profile views that have already been cut. The data is shortcut into the drawing with my cut profiles views. How do I get it to be in the cut profile views without re cutting everything?
I have an issue with a profile referenced into a plan sheet that is shifted when I view it in the plan sheet viewport. The profile stationing is correct in the profile dwg file and in the plan sheet dwg it is referenced into. But when I switch from model space to paper space in my layout sheet (the file the profile dwg is referenced into) the profile moves to the wrong station within my profile view in paper space.
The profile start station is 0+00, but it shifts to -1+00 within the viewport of my layout sheet.
The scales are the same between the dwg files (50) and the Annotation scale matches the dwg scales.
I am a C3D newbie who used ground survey points (Serrano_EG_surface) that generated a Civil 3D surface. The white line is consist of arc segments that I turned into polylines and then into individual CL alignments. The first alignment ,which has its left and right offsets do not generate the profile view that I needed to be created. There was a prompt asking for a profile to choose, but I don't know where in the drawing or in the propector panel to click on.
1. Are the ground survey points good enough so that any alignments over the those areas can provide me a surface profile, a design profile, cross sections every 50 feet, so that I can submit a preliminary drawing for environmental permitting. ?
2. When I check the object browser, the aligments preceding each other are not in the same elevation it seems. Do I have to to transform each of the polylines first into a 3d polyline and then an alignment so that I can create a profile.
3. Eventually , I wish to connect all these alignments to model a 1.5 mile rural road (more like an access road to a water reservoir).
4. What's a best techniques to keep track of modeling a road.This question pertains to e.g the object browser as one of the useful aid. I've also used the inquiry tool but not used it for its full potential.
I'am trying to create profile from opening.I have found interesting method : Profile.CreateFromProfile.But every time i call this method "eInvalidInput" exception is thrown.
I tried moving a Profile View and even though I selected everything at once and selected a base point and destination point, the Profile View Station and Elevation labels moved with a different offset than the Profile View itself. ?
I imported Google earth surface (at eye alt 600m) to civil 3d 2012 and created an alignment of length 181m.
When I exported same alignment to Google earth , it showed the length as 190m ( the difference increases with increase in length of alignment) And also the profile view of the alignment in the Civil D & Google earth varies.
I am writing a code using VB.net and i am trying to select the profile using its name and i am always having an exception error
ed AsEditor = Application.DocumentManager.MdiActiveDocument.Editor() Dim mydoc AsDocument = Application.DocumentManager.MdiActiveDocument Dim mydb AsDatabase= mydoc.Database Dim mytrans AsTransaction = mydb.TransactionManager.StartTransaction Dim mycivil As CivilDocument= Autodesk.Civil.ApplicationServices.CivilApplication.ActiveDocument Try
C3D 2012..Have a profile I'd like to have the PC, PT shown. (No Problem)But in doing so it also puts the PI'S of each of these curves in the profile view.
Is there a way to turn off the PI's and leave the PC's and PT's on?
why when i mesure the pipe diam prependicular in profile its less than the accurat dimension of the pipe whoever i changed the profile vertical exaggeration to 1, it still wrong? when mesured virtical it is ok
I only get 2 choices when selecting corridor feature line to create profile - ETW_base, and ETW_sub. My Subassembly has 2 pavement sections, a base and subbase section. I need the top of pavement profile.
I created a profile showing original ground and included superimposed profiles and an offset of the og line. Now when I open the drawing, the profile lines are gone. The grid is there, all of the profiles are listed under the alignment but they are not showing up. All of the styles are on and I've turned all layers on. I've tried to regain all and recover the drawing but the profile lines are not showing in the grid.
