I have a dynamic block which consists of a number of hatches, polylines and texts. The dynamic block has the property of being stretched and flipped.
Now the problem is that the normal grips which are being displayed for the normal lines, polylines and hatches are interfering with the stretch and flip grips. Is there a way to make autocad show only the dynamic grips.
Is there anyway to link standard AutoCAD Grips and there commands to Dynamic Block Actions? I want to stretch an arc by its midpoint grip. This accomplishes something that no other commands do.
View 4 Replies View RelatedI took the time to search and was unable to find anything that seemed relevant. I have also had trouble figuring out the documentation.
Is there a way to select a specific grip within a dynamic block and then update its position?
I have a block which represents a piece of equipment on a factory floor. It has two subcomponents which are blocked with the main equipment. Consider a rectangle and two smaller circles blocked together. Each of the subcomponents (circles) has a point parameter and a move feature so that the components can be moved independently from each other and from the main equipment.
Here's the issue: If a user accidentaly (or purposely) places the grip from one of the subcomponents snapped to the grip of the other subcomponent, then the two seem forever attached; when I try to grab the grip of one of the subcomponents to separate them, both grips get selected and both components move together. At this point the two components appear to be inseparable with the grips permanently joined.
Here's the question: Is there a way to separate the two components once their grips are made coincedent? Or is this a case of "just don't snap the grips together"? I'd like there to be a way to pull the components apart.
I have a line with shapes on each end like an aligned dimension. I want to have a grip on each end to let the user put the ends where they want.
I tried a polar stretch pair, with two rotation pairs, but am lost. The stretch is easy, but does not rotate the arrows to stay aligned to the line. I don't actually have arrows, but most know the behavior of aligned dimensions. I don't have extension lines though, like the dim would so ignore that part.
Any way to remove the alignment grip (the blue triangle / square thing) when you're creating a dynamic block?
I know you can remove the stretch grips and such, but I don't need an "alignment grip" and it's just another symbol that will confuse my users / clutter the block up.
My drawing- block is a little bit complicated, it contains few actions and parameters and everytime i open block editor to add, or to modify some action I can't see my drawing because actions grips and parameters grips obscure my drawing. I tried to refresh layout but it doesn't work.
please take a look on attached jpg.
I've made annotative blocks and I've made dynamic blocks... My intent is to integrate both but I can't find a way to move dynamic block parameters separately at different annotative scales.
In other words, if I insert an annotative dimension and add multiple scales I can move the dimension grips independently at each scale. If I insert a dynamic block I want to be able to use the dynamic block's action "grips" to do the same. However, with a dynamic block, if I move a stretch action at one annotation scale it moves the action at all annotation scales.
The attached file shows a simple example.
Currently developing a GUI, I'd like to remove the grips on selected objects when I launch a function from a toolbar. I have the classical ^c^c at the beginning of my scripts, but it doesn't seem to remove them, although pressing 2 times the esc keys does it...
View 4 Replies View RelatedI have created a dynamic block with several visiblility states. The block works great for what I need it for. however, I am trying to add one more action to the block but am having issues.
This block is essentially a 24" retail cabinet with the visibility states showing the different drawer and shelf configurations. I want to be able to lengthen the cabinet in 24" increments and have the visibility show for each 24" section.....e.g. I want a 10' cabinet so I bring in the 24" starter block. Then stretch the cabinet to the 10' mark, then I can chose any drawer/shelve config for each 24" section (they are all different).
I can get the block to stretch in 24" sections....no problem.....i just want the visibility state to be duplicated as well for each section. Now as it stretches, there is only one Vis state and it only populates the first cabinet.
I could do this by copying the block over and over 5 times.....but I am hoping there is a way to make this dynamic.
I have a block I am making into a Dynamic Block. I will be adding in different visibility states. Depending on the visibility state the block would need to be inserted from a different point.
My question is, is it possible to add multiple insertion points to a dynamic block so depending on the visibility state it defaults to the correct insertion point?
I have created an annotated block of a cut line. In the block editor the grips are located on the ends of the cutline where I need them to be. When I test the block in the block editor the grips are in the right place and the block works fine. However, when I insert the block into my drawing the grips to control the stretch action are located way out in right field instead of at the ends of the cutline where I placed them in the block editor. Parameters having errors. I have corrected the errors but my block is still acting the same way.
View 7 Replies View RelatedI have a problem with dynamic blocks.
I have inserted a dynamic block (with .NET) and changed the value of a dynamic parameter (Linear). The block is stretched as it should be. (no problems here).
After a fiew other routines, I select the block again (by using its objectID) and a want to get the coördinates of the grip of the linear dynamic paramter. Is there a way to get the coördinates based on the linear dynamic parameter and its grip points? code in vb.Net?
is there a way to make dynamic blocks stretchable similar to a mleader,
the blocks i create are only stretchable by grips, and not by crossing
(i am using linear or point parameter stretches)
See the snapshot below. There is a point on the timeline when the screen flips around and the video continues. How to cancel this effect? How this effect might have gotten there so that I can avoid having it happen again? The screen makes a 360 degree revolution. The video consists of on image on the main track with 6 pip tracks.
Unwanted Effect
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies View RelatedI need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies View RelatedI need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
usage of dynamic title blocks with visiblity states and defining page setup override templates which use same for quick plotting using sheet sets.
I have attached a simple dynamic block that I built which is the outter frame of our company title block, it is designed to allow users to quickly switch between Landscape and Portrait orientations.
The problem I am having is when I go to define page setups for my Sheet Set Page Setup Override Template I am unable to use the "Extents" option with auto-center because the "Extents", as defined by the page setup, includes ALL objects in the paper space regardless of visibility, so my title block ends up being centered in a stupid way if that printing configuration is used.
The only solution I have found is to use the "Layout" option when defining page setups, but this option produces other issues in other ways when printing. I don't want to use the "Window" option either for the potential for users to be using the page setup overrides to print drawings using different paper sizes or drawings that were not originally created using the current template the override is designed to accomodate.
Is there perhaps a system variable that defines whether invisible objects are included in the "Extents" setting in the page setup? I'm sure you'll all agree that Extents is the way to go in this situation, but it is not performing exactly as required.
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"
Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?
I'm working on a drawing and I want an action to work on two diffrent dynamic blocks.
In my case, I wish to have two blocks that I can rotate by one rotation grip.
How do I manage to work this out?
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
What is the variable to change the dynamic grip parameter size and color.
View 3 Replies View RelatedI'm working on a dynamic door, that has specific parameters to change its size and orientation. Everything works pretty good, only the arc for the door won't react the way I want it.
View 8 Replies View RelatedI photograph beach weddings. In my old software, I could remove swimmers and bathers, how in elements12? I am trialing it and cannot see any way to easially remove unwanted objects
View 1 Replies View RelatedI have a drawing that have blocks in them I cant find inserted. I cant purge them or the linetypes they have. How do I strip them out if I cant find them to explode them?
I have attached the file.