I have a really curvy sculpture. How do I draw the dimensions of the elevation for it?
I have attached a picture of my drawing. I was told to do gidelines and show the dimension of them. However I find it not very accurate for the contractors to read.
Is it possible to project an elevation drawn in CAD onto a curved wall in Revit?
The pattern of the cladding is very complicated and varies in both directions (curves) so it was easier to draw in in CAD, but I would like to project it on my curved wall in Revit, co that I could calculate the cladding areas accurately.
Can I use AEC Dimension in a Section/Elevation View in ACA? So, when an Wall height changes, the AEC will change too after refresh the section/elevation.
View 1 Replies View RelatedIs there a way to avoid super Elevation or Side Friction in Sloped Surfaces for Curves, such as Building Pads, Ramps, Floors, etc.. Is it mandatory.. ?? Its a problem all the time worrying about matching levels in topo surface and floors for gradual slopes in site and side friction in sloped ramps or sloped building pads.. that matching line between levels doesn't look good while giving presentations..
I have also attached an image for reference.. both the sloped surfaces are building pads..
I am designing a piece of public sculpture for outdoors. I have photographs of the location and photographs of my little model. I now need to insert the photograph of the little model into the location photographs and make it look like it belongs there. So I need the inserted model to adopt the environmental effects of it's surroundings.
I'm using CS5.5
How to create a flow arrow label for a feature line that parallels the curve?
I've a vague notion that this could be done with a dynamic block and a few fancy expressions. I'm comfortable with expressions, but I've never used dynamic blocks at all, so I wouldn't know where to start.
To be clear, I know curved text is possible, but I'm looking for a curved line (ie an arc) that would look 'parallel' to the arc of the feature line (ie have the same centre point). This would have to be dynamic to allow for different radii and for flipping to the left and right side of the feature line.
I want to extrude a big number of pillars to a rather complicated surface and that works out fine. But each end of the pillars warps around the surface and I want them just to go up to it and stop with a resulting horizontal face.
View 1 Replies View RelatedI am trying to create an elevation label that will give me the spot elevation followed by the letters "TC" and then on the line below subtract 4 inches from the elevation followed by the letters "BC". It's easy enogh to add the letters but the simple equation of elevation - 4 inches eludes me.
View 3 Replies View RelatedWhen I snap a point to an object, the point takes on the elevation of the object. I would rather the point's elevation stay as is.
-changing osnapz variable
-latest civil 3d service pack
A few weeks ago I did not have this problem but once my computer was switched to the company's global server and c3d was reinstalled the problem appeared. Furthermore (post switchover), when a colleage of mine prepared a simple test drawing with just a line and a point, he was able to snap to that line without the point changing elevation. When he sent that drawing to me and I tried snapping the point to the object, the same problem occured with the point taking the elevation of the line object. I suspect it is a system variable issue
i have some existing drainage pipe and structures in a base plan that i need to change the invert (which is the easy part) and the top elevation to the existing top elevation that does not meet the minimum presect in civil 3d 2012 is there a way to change these min. to match my exisitng elevation for example i have a catch basin invert is 15.45 top is 17.56 with a 18" rcp the cover will be less than 12" and i need to change this.
View 3 Replies View RelatedHaving a time getting ribs to align 2m below top of ridge beam, and connect to curved wall below. I created one, then arrayed, but the radius changes at each 2.5 degree interval. I don't think I should have to calculate the % radius change to get the beams to do this. Some constraint button maybe?
Not sure if editing a wall profile is the best way to model this, but it's working.
I am currently working in a facade that has a stylized gondola on it. The gondola has curved walls for the sides, and I need to have the curved cut to give it the shape. The tools I know are for straight walls, not curved. and the Opening/wall makes a squared opening, not curved.
View 3 Replies View RelatedI'm trying to get the dimension text that I pull out to the side closer to the actual dimension marks. The 2 1/2" and 2" shown have a minimum distance they can get toward their dimensions. I would like it to be about half of what it is, but so far I haven't been able to find the property that changes that.
View 3 Replies View RelatedI have one problem in ilogic "How to convert the normal dimension to driven dimension through ilogic"
View 4 Replies View RelatedIs it possible to override a dimension with some sort of formula or function that relates to the length of the dimension?
A simple linear scaling might be possible by inventing a new unit with the appropriate conversion ratio, but that wouldn't work. What I need for the dimension to display a length 400 less than the actual length.
How can I avoid getting zeros when creating dimension line with quick dimension command. the Zeros indicates the line itself. how it can be avoided?
View 5 Replies View Relatedhow to make a radius dimension a diameter dimension? I have Inventor Profession 2013.
View 1 Replies View RelatedIs there a way to override a dimension and have it shown as a GD&T Basic dimension. I can override a dimension with the text option but not with a box around the letter. It sounds strange to do this but the letter represents a dimension in a chart format that are Basic dimensions.
View 9 Replies View RelatedI want to insert dimension lines on this project. But instead of having an actual dimension I'd like it just to be a letter that refers back to a chart of possible dimensions for that element. How do I do this? I'm using AutoCad Architecture 2012.
View 1 Replies View RelatedCan i change the length of the dimension line 'extension' when my dimension text placement is beside the dimension line (see attached image)?dim line length.jpg
View 6 Replies View RelatedIs there a way to make the linear dimension a diameter dimension?
View 9 Replies View Relatedevery one now a day i am making isometric drawings so i m little bit confuse in that i am using dimension and change the oblige angle text of dimension so is it right way or not ????
View 9 Replies View RelatedWhen doing an angle dimension and trying to put text under the dimension line, the text types out straight which if long enough will extend over the dimension line. Other then creating text with arctext, is there no other way to get it curved? I am using AutoCAD 2010.
View 3 Replies View RelatedI found LucisArt sculpture effect useful to get higher midtone contrast, but i would like to know is it possible to do that in PS without plugin, then we weould have more control over it.
View 8 Replies View Relatedmy normal dimension style has text above dmension line & I want to add 'typical' to it below dimension line.
I have done this lot of time in my previous job an year back. but I can't seem to remember what to type between dimension text & the word I want to add in edit text box, so that it appers below dimension line.
I'm inserting dimensions and the tics keep coming out huge and not on the dimension line, in fact there's one on either side 20 ft out. If I change the drawing scale in the tab at a the bottom the tics get smaller and closer in, but they are still off the dimension string by a long shot.
View 3 Replies View Relatedis it possible to have a dimension style setup that shows the dimension text inline with the dimension - without having to move it?I have been looking but cannot seem to do it - is it possible and I am just missing it?
View 1 Replies View RelatedI'm working on a drawing that was converted into cad and it seems like every dimension has its own style. When I copy use the move comand or try to change the dimension the text changes from being above the dimension line to centered and the text gets closer together horizontally. When I compare a copied dimension to the original it has all the same properties including the text pos vert still being above text. The actual dimension style hasn't changed at all but what is showing up on screen is different.
Here a image showing three dimensions with the same properties, the top 2'-10" is what it should look like, the bottom is what it looks like when I copied it and the 1'-2" is when I make a new dimension.
I have a drawing of Polyline. The elevation of Polyline's are set different. But I don't need the elevation. So I change the elevation to 0. But after making it 0 all the polylines are scattered. How will I make the elevation to 0 not hampering the polylines.
View 6 Replies View RelatedAt the top of the clock, how do you draw the curved lines, which say radius of 4.
[URL]........
So I need a starting point on how to draw on a curved surface.
[URL]
how to draw the "slot" I know in solid works i can "project" onto the surface and then so a cut.