When doing an angle dimension and trying to put text under the dimension line, the text types out straight which if long enough will extend over the dimension line. Other then creating text with arctext, is there no other way to get it curved? I am using AutoCAD 2010.
View 3 Repliesevery one now a day i am making isometric drawings so i m little bit confuse in that i am using dimension and change the oblige angle text of dimension so is it right way or not ????
View 9 Replies View RelatedCan i change the length of the dimension line 'extension' when my dimension text placement is beside the dimension line (see attached image)?dim line length.jpg
View 6 Replies View Relatedmy normal dimension style has text above dmension line & I want to add 'typical' to it below dimension line.
I have done this lot of time in my previous job an year back. but I can't seem to remember what to type between dimension text & the word I want to add in edit text box, so that it appers below dimension line.
is it possible to have a dimension style setup that shows the dimension text inline with the dimension - without having to move it?I have been looking but cannot seem to do it - is it possible and I am just missing it?
View 1 Replies View RelatedI'm making this diagram of the load condition acting on tunnels to explain a Japanese set of equations that are used for the structural analysis for tunnels:
load condition for EEM.jpg
But, there is one problem I have. I'm trying to set up the text for the dimension between the water table and the tunnel "Ha" to look horizontal.
However, if I click on the properties box and write 90 in the rotation box right next to where it says "text rotation," the dimension text does not rotate 90 degrees; if instead I try to rotate it 180° then it only rotates 90° (and in the opposite direction) instead of 180°. It doesn't matter how many degrees I choose, it won't rotate my dimension "Ha" to desired angle to make it look horizontal.
OK I know it's hard to explain my problem with just writing, so I've posted a few pictures:
In this one, the dimension is at 0°; I've only opened the properties box to attempt and rotate it: no rotation.jpg
Now I write 90 in properties box but the dimension text does not rotate at all; it remains at 0 as it is shown in the following image: 90 & no rotation.jpg
Next I try to rotate 180, just to see what happens; and it does rotate (only 90 degrees!): 180 rotates 90.jpg
I finally try to rotate the text 270 just to see if it rotates to desired angle and it does rotate (180 degrees from original position). As shown below:
270 last try.jpg
It doesn't matter how many degrees I choose, I cannot make it look horizontal.
How can I set up my dimension text "Ha" to look horizontal?
How can I avoid getting zeros when creating dimension line with quick dimension command. the Zeros indicates the line itself. how it can be avoided?
View 5 Replies View RelatedI want to insert dimension lines on this project. But instead of having an actual dimension I'd like it just to be a letter that refers back to a chart of possible dimensions for that element. How do I do this? I'm using AutoCad Architecture 2012.
View 1 Replies View RelatedI'm trying to get the dimension text that I pull out to the side closer to the actual dimension marks. The 2 1/2" and 2" shown have a minimum distance they can get toward their dimensions. I would like it to be about half of what it is, but so far I haven't been able to find the property that changes that.
View 3 Replies View RelatedHow do I edit a dimension text to add a second line (so dimension on top of the line and text on the second line)?
View 3 Replies View RelatedOne of my dimension scales doesn't draw a line back to the dimension when I move the number away from the dimension line. All my other dimensions do it. I keep looking for the setting that must be changed but I cannot find it. What setting creates a line from the dimension number back to the center of the dimension line if you pull the dimension number away from the line?
View 4 Replies View RelatedIs there a variable to force dimension text line to show? I am using annotative dimensions and the placement for the text is forced to the outside of the dimension if it doesn't fit. I get annoyed on having to move the text to show the dimline above the dimension.
View 3 Replies View Relatedhow to edit the line space distance for the dimension text. I can change the style, size and several other features. But the line space distance is the one thing I can't seem to edit. The only solution I know of and use is exploding the dimension and then the text turns to mtext and the option becomes available. But then if the section changes to a shorter/longer area, i have to go through several steps with the exploded lines. how to edit the line space distance for the annotation in the dimensions. i have also attached a pic of my issue as well.
C3D 2014 SP1
DELL Precision T3600
Intel Xeon E5-1650 @ 3.20GHz
NVIDIA QUADRO 4000 Dual Monitor
32 GB RAM / Win7 Pro 64-bit
I am trying to edit the placement of vertical text within a dimension line - I wish for the text to be outside the dimension line not inside.
View 4 Replies View RelatedIf I place a dimension and have text above and below the dimension line (using X), and then grip edit the dimension text to move it for space/clarity on plans, the text above and below the line will mysteriously move closer to the line. If I have backgrounds applied to the text, which I normally do, the backgrounds will cover the line. Even without the background, it looks odd next to other dimensions that were not grip edited.
Civil 3D 2011
Windows 7 x64
Is there any way to create the angle dimension shown in the attachment without creating a small line in a sketch first?
View 9 Replies View RelatedI want to ask how to make the size for the angle in the distance between holes. i use the autodesk inventor 2013, I attach an example like this.
View 9 Replies View RelatedIs there any way possible to have an angular dimension to denote an angle of greater than 180 degrees?
View 4 Replies View RelatedFor some strange reason I can not print and dimension lines with an angle reference. I get the error "Cannot find or create the font AerialMT".
However, I have this font on my machine. Triple checked and installed it again.
I have one problem in ilogic "How to convert the normal dimension to driven dimension through ilogic"
View 4 Replies View RelatedIs it possible to override a dimension with some sort of formula or function that relates to the length of the dimension?
A simple linear scaling might be possible by inventing a new unit with the appropriate conversion ratio, but that wouldn't work. What I need for the dimension to display a length 400 less than the actual length.
how to make a radius dimension a diameter dimension? I have Inventor Profession 2013.
View 1 Replies View RelatedIs there a way to override a dimension and have it shown as a GD&T Basic dimension. I can override a dimension with the text option but not with a box around the letter. It sounds strange to do this but the letter represents a dimension in a chart format that are Basic dimensions.
View 9 Replies View RelatedIs there a way to make the linear dimension a diameter dimension?
View 9 Replies View RelatedI am having an issue with my dimensions. If I have a dimension that is 1'-3" or larger, my extension line beyond my dimension line extends the normal length, but as soon as my dimension goes under 1'-3", the extension line then gets twice as long outside of the dimension line (see attachment). I have researched...and i can't seem to find a dim variable that will let me change this. is there anything to control this happening once my dimension goes below 1'-3"?
View 1 Replies View RelatedI'm inserting dimensions and the tics keep coming out huge and not on the dimension line, in fact there's one on either side 20 ft out. If I change the drawing scale in the tab at a the bottom the tics get smaller and closer in, but they are still off the dimension string by a long shot.
View 3 Replies View RelatedI need to routinely insert text into or near my dimensions but my dimensions need to be kept as basic dimensions meaning they need to have the box around them as in the picture. What I want to do is what the first dimension shows with the "2x" outside the dimension box but that first one is a combination of suppressing the dimension line and inserting a leader so the 2x will be within the line. Otherwise the normal dimension is what is shown below. How can I increase the line gap from the dimension options without 1) increasing the dimension box with DIMGAP or 2) inserting a line that's separate from the dimension itself or 3) exploding
View 4 Replies View RelatedCommand line for Dimension Fit
View 1 Replies View RelatedHow do you Associate a dimension to a line using VB. I have not had any results searching for an example of this.
View 7 Replies View RelatedI have a dimension line that says 5' and I want to change only the number to 8'.
View 9 Replies View Relatedhow I can adjust my dimension line to the drawing with the white background ?
drawing.jpg