AutoCad 2D :: DWG Converted To PDF Then PDF Not Printing To Scale
Jun 18, 2012
My client needs an a3 drawing I drew converted into a PDF so he can print the PDF off to the correct scale.
I created the pdf in autocad 2012 to A3 size and a scale of 1:1. I emailed the PDF to my client who now says that the PDF is not to the correct scale when he prints it, I instructed him to select the 'actual size' option he then said it cut off the drawing at either end of the drawing. He getting very angry now. He wants to be able to open the PDF press print and it to print out to scale.
View 9 Replies
ADVERTISEMENT
Oct 2, 2012
I just found out that the last couple of drawings I have produced/worked on all have incorrect dimensions on them. I have spent a couple hours scouring the internet and cannot find any fixes.
My dimensions all work, and add up to what I am drawing, but when I print the sheet everything is out of scale. I have attached a simple drawing as an example. I drew a 190mm line and printed it 1:100. When I measure the line it comes to just over 4.8mm.
CCSV.dwg
View 8 Replies
View Related
Nov 16, 2010
I work for a demolition company and and trying to print off site plans, sent to us by clients (which are drawn in CAD, but sent to us as pdf's), to scale on an A1 printer.
The documents being sent to us are supposedly to scale @A1. I have tried printing both in adobe and bluebeam but both programmes seem to lose accuracy and consistency between drawings.
What is the easiest and cheapest way of measuring, then printing pdfs to an accurate scale.
View 9 Replies
View Related
Jan 20, 2012
I am having an issue printing to scale. When I print my drawings, the scale is about 4" over 100' out of scale (short) All of the settings are correct for plotting. This happens whether we print directly or to a pdf first. I know it is not just the plotter as I have tried three different printers with the same result. Also, I know it is not AutoCad as we are having the same issue printing from Microstation. I
View 9 Replies
View Related
Nov 14, 2013
So if I am in a layout page and I plot the sheet directly to our printer the drawing comes out to scale.However if I plot to PDF using DWG to PDF.pc3, and then print to printer it is always slightly smaller around 10% to 15% smaller.
View 5 Replies
View Related
Jun 27, 2012
We have a number of printers in our office, an A3, an A1 plotter and an A4 printer.
After printing off the same drawing to the A3 and the A4 yesterday, I realised the A4 printer is printing around 95% of the size it should be printing.
I don't even know where to start fixing this problem; the user manual for the HP Officejet Pro 8000 Enterprise [I know!] doesn't even reference scale at all. It could be an issue with CAD linking to the printer my computer linking to the printer the printer My colleagues are having the same issue, so it's not just my computer or settings.
View 4 Replies
View Related
May 25, 2011
I'm trying to convert a hand drawn paper plan of our house into Autocad so that I can tweak it. I'm not bad at drawing things in autocad, but how to set it up properly for the file to be printed out in a shop on A0 at the correct scale. Either some info on how to set it up, or a template file that is already setup would be great.
View 9 Replies
View Related
Jul 22, 2011
After creating a pdf.... when printing that pdf at non scale, the edge of the title block gets cut off. how can I fix that in adobe still using non scale format.
View 2 Replies
View Related
Mar 11, 2009
I've drawn some maps in photoshop 7 and i want to print them out so 1 square on the map will come out of the printer as 1 inch.
I understand terminology but i dont' have a lot of experience with photoshop.
way to go about measuring up 1 square on screen so that it prints out 1 inch.
View 2 Replies
View Related
Apr 1, 2008
When I print in revit - at scale - 100% Zoom, I check it with an architecture scale and its off. For example, 25' - 0" in the revit file measured with a scale on paper is 23 ' 10". etc... Is it a revit issue, or a printer driver issue?
View 7 Replies
View Related
Jul 9, 2013
I am using the student version of Revit and have desparately been trying to create a document that would print to scale. I use PDF creator to convert Revit to pdf, but it always comes messed up by an inch or so...insted of 4.6, it prints 4.75 (or the other way around). I tried formating my title block in many different ways, including deleting the outer lines. Nothing works. There is no Arch D format in the family of titleblocks. I am a complete beginner, just started using Revit a couple months ago, with no knowledge of CAD or anything similar. When I look at the PDF creator page of my doc, it shows that the doc has been properly sized, but when the print place prints it out, it is off by 1" or so.
How do I format my sheet so it prints to scale in format 24" X36"?
View 2 Replies
View Related
Aug 3, 2012
Can you print a model file to scale without setting up a view with a scale? Like in Autocad, you could print the model space to a certain scale within the page setup manager. Does revit have anything like that? Or do I have to set up a sheet view prior to printing anything?
running revit architecture 2011.
View 1 Replies
View Related
Aug 13, 2013
I just recently noticed that when I print documents from Revit Architecture, they are printing smaller than the scale size they are set to. I verified with a couple of different scale settings against a good old fashioned scale ruler. It seems to be consistently incorrect.
View 3 Replies
View Related
Apr 17, 2012
exporting my CorelDrawX6 files as a high quality jpg for large scale printing purposes. In X4 it was very easy - just export as usual to the highest quality cmyk jpg and open in Photo Paint... now when I export this way it takes forever to bring up the preview page and most of the time it ends up being blank. Sometimes even crashes. I have played with all options in the filter dialog menu that I can find but nothing works. Thought it might be a file size problem but never had that problem in X4 and anything under 200dpi will not be high enough quality.
View 11 Replies
View Related
Dec 30, 2012
I use Canon 60D and normally shoot in mRAW. I am considering a move to DNG conversion so I did some test conversions and was amazed to find that, far from reducing the size of my mRAW files, it increased them by about 60%. I repeated the exercise with RAW files and found that this did reduce the size of the files by over 10%. In fact, i ended up with the crazy situation where the DNG files converted from mRAW were much bigger than those converted from RAW.
Below are some sample sizes based on Medium previews, Embed fast load data - YES, Embed original RAW file - NO, Compatibility Camera Raw 7.1 and later
Before : mRAW 17Mb mRAW 12Mb
After: DNG 28.5Mb DNG 21Mb
Before: RAW 23Mb RAW 22Mb
After: DNG 20Mb DNG 19Mb
If I went for Full Preview, the DNG sizes rose by about 2 Mb
why the mRAW conversion is so inefficient?
I am still not entirely sure whether to adopt DNG but, if i do, it looks like I certainly won't be using mRAW as the source.
View 1 Replies
View Related
Dec 2, 2011
I have a complex (includes tints) clip art object that needs printing in a specific pantone color I just convert it to grayscale using edit>find and replace objects>color mode. then print it as a black plate and just use another color on press.
Today I had to send off artwork to another printer. Dang. How to install a macro. Import clip art to be modified to a new document, do not do this in your working document.
Use Edit>Find and Replace> Find Objects
Replace a color model or palette. Next
Leave as is except change Replace with color model to "Grayscale" Next>Replace all
Repeat 2-4 for 'outlines' if you have them.There you now have a gray scale clipart, but the fun continues!You'll need to know what pantone color you want to use. Let's say Reflex Blue. Make a square and color it Reflex blue from a pantone palette.Duplicate the square and create swatches at 90% 80% 70% etc down to white.Select these square swatches, then Windows>Color Palette>Create Palette from Selection. Save palette with a temporary name, it is only time use. Or you could call it 'Reflex Blue'Now go to this website and download the macro "limit colors" URL...
Drop it in your GMS folder in under your username to install the macro. (might have to save the drawing and restart Corel...)Once you reopen your now grayscale clipart document, Select the clipart. Run the macro (Tools>Macros>Run Macros) LimitColors.Posterize select the number of colors in your new palette if you created 10% swatches, go with 11, if you did steps of 20% then you'll do 6 (don't forget white).Run the macro LimitColors.LimitColors and select your new palette you made in step 9.
View 12 Replies
View Related
Mar 18, 2013
I've opted for 3D scan of a part, it is Shoe Horn. And the scaned people sent me an .igs format and I requested them to mail me .dwg format to work with ACAD2007. Accordingly they too converted .igs to .dwg, but the converted .dwg file is unable to convert into surface or solid, once if it could be converted in surface or solid only we can do further development.
convert this into surface or solid. make this as surface or solid model, to work further with ACAD 2007.
View 9 Replies
View Related
Jan 12, 2012
i'm using Autocad2012 now. when i use paste special in objects and give x or y insertion scale. after i do explode that object the arcs are converted in to ellipses and it come with ellipse grips. before 2012 version it won't happen. what's the change in autocad 2012? is there any variable to change?
View 3 Replies
View Related
Oct 2, 2012
I have a 2d dxf file (attached) that i need to somehow convert into a 3d file with a material thickness of .75 inches (a piece of wood) so that the cnc can cut it it keeps giving me an error of no thickness in the machine.
View 4 Replies
View Related
Dec 18, 2013
I created an assembly for a customer of mine who wants a STL of a sword for a possible 3D print situation. I created the part in inches and finished it. When I converted I made sure the document units were set to inches and the export options were as well. However whenever they upload it or check it in other software it is coming up miniscule like it was drawn in mm or cm. I have gone through a number of forums and updated to the latest service pack without issue. Is the issue related to the fact its an assembly being converted to an STL? I have done it before without issue. I have attached the STL in question.
View 6 Replies
View Related
Apr 13, 2012
I have just updated to Autocad 2013. While working on existing drawings (previously created in V2012), I am having issues with the SCALE command. Most times, but not always, when I add a line or block, with a base point on an existing line or object and try to scale it, I get an "extremely small scale factor ignored" message, although I did not get a chance to enter a scale factor. While it appears most times, but not always, if I draw a new line in empty space on that same drawing, I am able to use the SCALE command without problems. I also have the same issue when trying to scale an existing line or block, most times but not always.
Here is a copy of the command line while I am trying to make it work:
Command: l
LINE
Specify first point:
Specify next point or [Undo]: 100
Specify next point or [Undo]:
Command: sc
SCALE
Select objects: 1 found
Select objects:
Specify base point:
Specify scale factor or [Copy/Reference]:
Extremely small scale factor ignored.
Command:
SCALE
Select objects: Specify opposite corner: 1 found
Select objects: Specify opposite corner: 1 found, 2 total
Select objects:
Specify base point:
Specify scale factor or [Copy/Reference]:
Extremely small scale factor ignored.
If you notice, it does not give me the chance to enter a scale factor. As soon as I pick the base point, it skips over to the error message, yet displays the scale factor prompt with a blank factor. I'm experiencing this issue on various files (not all but most), so I don't think it is a corrupt file. Why I get this and if I can correct it?
View 9 Replies
View Related
Jun 26, 2009
am in the process of setting up a standard file for all designers to use our local office. This file will have most of the styles created for profiles, alignments, surfaces, profile views, etc... as mostly specified by the customer and industry standards.
I am having trouble maintaining the correct annotation scale in the viewport in paperspace and when plotting.
The attached word document has 3 figures. Fig 1 shows the correct viewport scale and correct annotation scale. Fig 2 shows how the annotation scale abruptly changes during the plotting process. This abrupt annotation scale change sometimes happens during the regen process or when I switch from layout to model space and back to layout.The annotation scale goes from 1:1 to 1:40 just as in the viewport. This change in annotation scale is not supposed to happen because I want to preserve a certain plotting height for my text versus a viewport scale by using various annotation scales.
I have researched the procedures for annotation scale and have not found any info related to this "abrupt change in annotation scale".
Curiously , this abrupt change in annotation scale does not happen if the text does not belong to any styles within Civil 3D. Stand alone text stays at the correct annotation scale and is not affected in the same way.
View 9 Replies
View Related
Jun 27, 2012
We have recently noticed that after printing a PDF of a drawing I plotted from AutoCAD we are coming up with differences when we double check the scale on the printed hardcopy using a carpenter ruler.
For example, there is a dimension labeled on the drawing of 200 ft. However, if I try to scale this out with a carpenter's ruler at the drawing was set to (say for instance it is 1 inch = 100 ft) I am coming up short of the 2 inches it should be (typically come up around an 1-15/16" or around 194 feet, approx 97% of the correct amount).
In the Page Setup Manager in AutoCAD, I have the following options selected (see the print screen as well):
Printer/plotter selected: DWG to PDF.pc3
Paper Size: ANSI full bleed B (11.00 x 17.00 Inches)
What to Plot: Layout
I don't have a plot scale scale other than the default 1" = 1'
No plot style selected
Then, on the print menu when I open the PDF that I have exported from AutoCAD, I have the following settings (see the print screens I have attached):
Printer: The printer I use (Konica Minolta c650 Series PCL)
And I have selected the Options "Auto Rotate and Center" and "Choose paper source by PDF page size**"
** Note, that I have tried unselecting the "Choose paper source by PDF page size" option and accordingly changed the paper size in the "Page Setup..." button at the btoom to match the document size (i.e. 11.0 x 17.0in) and it gets the difference to be closer (i.e. I now get 198 ft but some of my border gets cut off). See the print screen below for this a print screen of the print menu and sub-menu of Page Setup showing the paper size selected.
I saw that some people in other forums state that there is no real solution when trying to scale off of PDF's and that there should be a disclaimer saying as much if you are to send the file out to a customer who may rely on doing some in the field scaling from the printed copy of the PDF file. I find it hard to believe there is no solution as we have received some drawings from others whom the scaling works just fine.
View 3 Replies
View Related
Jun 27, 2013
When I open a new drawing in my AutoCAD 2013 that I just recently installed last week, I encounter a problem that I am not familiar with from previus versions of AutoCAD I have worked on. First of all, the units default to decimal, and I want them to default to architectural, with feet and inches. I have to type UNITS in the command line every time I open a new drawing in order to adjust this. I have AutoCAD for Architecture 2012 on another computer, and the program automatically defaults to architectural units upon opening up. Just to let you know, the program I am having this difficulty with is part of a package called Autodesk Building Design Suite 2013. I was under the impression that it included AutoCAd for Architecture, but I think it has only standard AutoCAD.
The scale of the objects I draw vs. the scale of the drawing field is very out of proportion. What I mean is, when I open a new drawing and draw a 30' -0" line, the line appears so long on the screen that I cannot see the whole object, even if I zoom out to the maximum. I should be able to see the object in it's entirety. In fact, when I draw a line that is only 12" long, even when the zoom is all the way out, the line looks huge in length. I have tried adjusting the units to the architectural/inches setting of course, and I have tried adjusting the scale in model space from 1:1 to 1/4'=1'-0", but nothing is working.
View 4 Replies
View Related
Aug 9, 2012
I am working on automating page setups in model space and am looking for a way to set the plot scale equal to the annotation scale for scaled drawings with
(setvar "filedia" 0)
(setq a (getstring (getvar "cannoscale")))
(command "-plot" "YES" "MODEL" "" "" "" "" "" "" !A "" "" "" "" "" "" "_Y" "_N")
Setting the plot scale with !A causes the lisp to fail. However, when running each prompt through the command line individually, !A works fine. what is missing?
View 2 Replies
View Related
Nov 22, 2013
I am trying to insert a block into a file in Acad 2014 and it comes in too large. If I insert the same block into the same file using Acad 2012 it comes in at the correct scale. Doesn't seem to matter if insunits is 0 or 1, or insunitsdefsource or insunitsdeftarget are also 0 or 1.
There must be some variable or variables I'm missing.
View 3 Replies
View Related
Mar 29, 2011
I have a Viewport set to scale 1:100 and the Viewport is locked.The Annotation Scale displayed in the Viewport was 1:50.
When I clicked on the Synchronize Icon beside the Viewport Scale, the Viewport Scale changed, even though the Viewport was locked.
I was expecting the Annotation Scale to synchronize to the Viewport Scale.
Is this how it is supposed to work? and why does a locked Viewport Scale change?
View 2 Replies
View Related
Apr 19, 2013
I have a block that i would like to scale based on the plot scale when plotting.
We set up our drawings full size and occasionally we want to plot them at half size. We do this by setting the plot scale to 1:2 (custom) in the plotting dialog. We have a few blocks that we want to print at the same size on paper, essentially become twice as big.
Is there is a way to fix the size or just set a few scale states and have them automatically adjust based on the plot scale (not drawing/annotative scale)?
View 1 Replies
View Related
Nov 8, 2013
I have a drawing with several layouts, and in one particular layout only, I want the text to be smaller than the annotation scale would dictate (the viewport is 1"=300', but I want the text to display at 1"=50' annotation scale).
I tried selecting the viewport and changing the "annotation scale" property to 1"=50', then the "standard scale" property to 1"=300'.
Strangely, this seems to work for a bunch of MText objects I have in the drawing, but it won't work for an alignment station label group or for a particular linetype...for some reason, those two things insist on having their annotation scale equal to the viewport scale.
I tried messing around with the alignment station label group's style but couldn't figure anything out. As far as the line/linetype, I'm completely at a loss why that one wouldn't change.
View 3 Replies
View Related
Apr 15, 2013
I have a 3D part, which I want to scale down to 0.5 the size in X and Y direcions, but I don't want to scale it down in Z direction.
Is this even possible? How do I go about doing it?
View 9 Replies
View Related
Sep 6, 2013
AutoCAD 2013 2D - when scrolling the viewport scale list, the viewport zooms with each scale instantly.
View 1 Replies
View Related
