When I print in revit - at scale - 100% Zoom, I check it with an architecture scale and its off. For example, 25' - 0" in the revit file measured with a scale on paper is 23 ' 10". etc... Is it a revit issue, or a printer driver issue?
View 7 RepliesI am using the student version of Revit and have desparately been trying to create a document that would print to scale. I use PDF creator to convert Revit to pdf, but it always comes messed up by an inch or so...insted of 4.6, it prints 4.75 (or the other way around). I tried formating my title block in many different ways, including deleting the outer lines. Nothing works. There is no Arch D format in the family of titleblocks. I am a complete beginner, just started using Revit a couple months ago, with no knowledge of CAD or anything similar. When I look at the PDF creator page of my doc, it shows that the doc has been properly sized, but when the print place prints it out, it is off by 1" or so.
How do I format my sheet so it prints to scale in format 24" X36"?
Can you print a model file to scale without setting up a view with a scale? Like in Autocad, you could print the model space to a certain scale within the page setup manager. Does revit have anything like that? Or do I have to set up a sheet view prior to printing anything?
running revit architecture 2011.
I just recently noticed that when I print documents from Revit Architecture, they are printing smaller than the scale size they are set to. I verified with a couple of different scale settings against a good old fashioned scale ruler. It seems to be consistently incorrect.
View 3 Replies View RelatedI have a floor plan with a very long footprint in a "View" drawn at a convenient scale.
The long building had to be broken to be put on several different "Sheets", and each of the floor plans on each of the sheet has a scale.
When I change the scale of the partial plan on one "Sheet", all the other sheets also change to the same scale and also the original view changes to the new scale.
Is there a way to assign the desired scale of the plan on one sheet without affecting the scale on the other sheets and on the original drawing view?
I created a wall detail in a scale of 3/4"=1' and when I change the scale to 3"=1' the hatching becomes smaller. I want the hatching to get larger without having to redraw it.
View 1 Replies View RelatedI've drawn some maps in photoshop 7 and i want to print them out so 1 square on the map will come out of the printer as 1 inch.
I understand terminology but i dont' have a lot of experience with photoshop.
way to go about measuring up 1 square on screen so that it prints out 1 inch.
I just found out that the last couple of drawings I have produced/worked on all have incorrect dimensions on them. I have spent a couple hours scouring the internet and cannot find any fixes.
My dimensions all work, and add up to what I am drawing, but when I print the sheet everything is out of scale. I have attached a simple drawing as an example. I drew a 190mm line and printed it 1:100. When I measure the line it comes to just over 4.8mm.
CCSV.dwg
I work for a demolition company and and trying to print off site plans, sent to us by clients (which are drawn in CAD, but sent to us as pdf's), to scale on an A1 printer.
The documents being sent to us are supposedly to scale @A1. I have tried printing both in adobe and bluebeam but both programmes seem to lose accuracy and consistency between drawings.
What is the easiest and cheapest way of measuring, then printing pdfs to an accurate scale.
I am having an issue printing to scale. When I print my drawings, the scale is about 4" over 100' out of scale (short) All of the settings are correct for plotting. This happens whether we print directly or to a pdf first. I know it is not just the plotter as I have tried three different printers with the same result. Also, I know it is not AutoCad as we are having the same issue printing from Microstation. I
View 9 Replies View RelatedSo if I am in a layout page and I plot the sheet directly to our printer the drawing comes out to scale.However if I plot to PDF using DWG to PDF.pc3, and then print to printer it is always slightly smaller around 10% to 15% smaller.
View 5 Replies View RelatedWe have a number of printers in our office, an A3, an A1 plotter and an A4 printer.
After printing off the same drawing to the A3 and the A4 yesterday, I realised the A4 printer is printing around 95% of the size it should be printing.
I don't even know where to start fixing this problem; the user manual for the HP Officejet Pro 8000 Enterprise [I know!] doesn't even reference scale at all. It could be an issue with CAD linking to the printer my computer linking to the printer the printer My colleagues are having the same issue, so it's not just my computer or settings.
My client needs an a3 drawing I drew converted into a PDF so he can print the PDF off to the correct scale.
I created the pdf in autocad 2012 to A3 size and a scale of 1:1. I emailed the PDF to my client who now says that the PDF is not to the correct scale when he prints it, I instructed him to select the 'actual size' option he then said it cut off the drawing at either end of the drawing. He getting very angry now. He wants to be able to open the PDF press print and it to print out to scale.
I'm trying to convert a hand drawn paper plan of our house into Autocad so that I can tweak it. I'm not bad at drawing things in autocad, but how to set it up properly for the file to be printed out in a shop on A0 at the correct scale. Either some info on how to set it up, or a template file that is already setup would be great.
View 9 Replies View RelatedAfter creating a pdf.... when printing that pdf at non scale, the edge of the title block gets cut off. how can I fix that in adobe still using non scale format.
View 2 Replies View Relatedexporting my CorelDrawX6 files as a high quality jpg for large scale printing purposes. In X4 it was very easy - just export as usual to the highest quality cmyk jpg and open in Photo Paint... now when I export this way it takes forever to bring up the preview page and most of the time it ends up being blank. Sometimes even crashes. I have played with all options in the filter dialog menu that I can find but nothing works. Thought it might be a file size problem but never had that problem in X4 and anything under 200dpi will not be high enough quality.
View 11 Replies View RelatedI notice that a 3D view on a Sheet, when the view is "activated" and with the crops regions on, can be reshaped, but I do not see a way to make what is shown on the view a tad "larger" (i.e., bigger, like zooming in). (I have tried, but I might be missing something?)
I wonder if there is way to scale a 3D on the sheet, to make the "scale" of only one of the 3D's larger on this sheet (without affecting the scale of the other views on the Sheet). Is this possible?
I am creating a scale model for a laser cutter using 1/4" mdf. So my drawing needs to be 1/4". How do we change the Revit custom scale to 1"=1/4" OR 1/4" = 1/4"?
View 1 Replies View RelatedMy Site Plan Scale is greyed out, what could be causing this?
View 2 Replies View RelatedI can't change the scale of a dwg. on a sheet. Can you uggest what I need to do?
View 1 Replies View RelatedQuestion #1: To my Sections Sheet, I am adding a Key Plan of each floor to show where the sections are cut. I duplicated a plan of each floor and renamed it "Floor # - Key Plan", and added the view to the Sections Sheet at a small scale, and now I am using a 1" = 80'-" scale for these key plans. I am able to hide all the unwanted annotations elements, but I notice that some like the "UP" and "DN" of stairs, which are very large, do not go away without erasing the stairs also.
How can I leave the stairs at this small scale but without the associated annotation?
(I also notice that this happens with elements like Washer (W), the Water Heater (WH), etc).
Question # 2. Related question: Do Revit has a "Key Plan" creation fuction to automate this work?
Any luck in creating a graphic bar scale to place on your sheets or in your drawings.
View 6 Replies View RelatedToday I adjusted our title block. Scale is automated by the scale view of the views placed. It becomes 'as indicated' is multiple scale are used. No problem, that part I can live with (/ workaround).
Sadly the scale doesn't appear on a sheet list schedule. Which surprises me . With revit 2012 I was wondering: I am wrong? If not: do you have a nice workaround which doesn't mean I have to manually input it.
When i import a pointcloud into revit the scale is not right. Is there a way to fix this
View 1 Replies View RelatedI am doing a generic annotation with several rows of text, but I need to read the view scale in the project to set the spacing between the rows of text. My idea is to create a parameter that will be multiplied by the scale factor in the view.
View 3 Replies View RelatedI have a complex (includes tints) clip art object that needs printing in a specific pantone color I just convert it to grayscale using edit>find and replace objects>color mode. then print it as a black plate and just use another color on press.
Today I had to send off artwork to another printer. Dang. How to install a macro. Import clip art to be modified to a new document, do not do this in your working document.
Use Edit>Find and Replace> Find Objects
Replace a color model or palette. Next
Leave as is except change Replace with color model to "Grayscale" Next>Replace all
Repeat 2-4 for 'outlines' if you have them.There you now have a gray scale clipart, but the fun continues!You'll need to know what pantone color you want to use. Let's say Reflex Blue. Make a square and color it Reflex blue from a pantone palette.Duplicate the square and create swatches at 90% 80% 70% etc down to white.Select these square swatches, then Windows>Color Palette>Create Palette from Selection. Save palette with a temporary name, it is only time use. Or you could call it 'Reflex Blue'Now go to this website and download the macro "limit colors" URL...
Drop it in your GMS folder in under your username to install the macro. (might have to save the drawing and restart Corel...)Once you reopen your now grayscale clipart document, Select the clipart. Run the macro (Tools>Macros>Run Macros) LimitColors.Posterize select the number of colors in your new palette if you created 10% swatches, go with 11, if you did steps of 20% then you'll do 6 (don't forget white).Run the macro LimitColors.LimitColors and select your new palette you made in step 9.
I have a problem with printing - problem to *.plt files I can’t use printing sets View/Sheet Set Revit creates empty files or loses parts of drawings I have Revit Architecture 2011 and 2012, Revit MEP 2011 and 2012 with every services pack All my PC Stations are (Dell Precision T3500 (6GB RAM) Windows 7 Ultimate 64 BIT) I tested 3 PC Stations and 3 types of printers (TDS400, HP DesignJet 1050, HP DesignJet T770 Printing size was A0 and A1. where is my mistake or what kind of limitations has Revit?
View 5 Replies View RelatedI have a view title where I want to show Full scale and half scale on the same view title. Please see attached .rfa file.
Is there a way to have a label return a half size automatically in an effort to have only one view title. Otherwise our current work around is to make each view title for each scale and create a viewport for each scale in our template. I have heard that the labels are hardcoded and cannot be changed.
Are there any neat tricks to scaling a DWG inside a block with parameters? I would assign a scale factor parameter to Instance Scale but as I can't I'm looking for a workaround.
I have a some 2D elevation trees that I want in my 3D tree block and alI just want to control the height. The problem is that if I explode the DWG in a family everything just disappears .
It is the way we scale 1 / 100 the size of our ِDimension, the scale to 1 / 500 to change the size of the enterprise to automatically change the scale.
This method is applicable in AutoCAD, but I could not find the software.
Where I need to go to change the scale of a fill pattern. I have brick walls that the brick facade scales about 1/2 of what it should be.
View 1 Replies View Related