what the best way to show 2 different subassemblies based on the same iAssembly... I would expect a "custom" option as there is from the content center. If I try and change the table for one, the other instance gets updated, and I would like it to stay the same. I understand that this would require a new "branch" in the BOM holding the different sized parts, but there must be a way to accommodate this?
View 1 Replies
I am creating an iAssembly with iParts. Some of the iParts have the "Table Replace" colum option and some do not. Both iParts have tables with members and part numbers. See pic.
View 3 Replies View RelatedIs there any way to insert a generic table into an assembly file. I don't want to create an iAssembly or use the data to configure the component in any way. I would just like to be able to maintain some design related information within the assembly file, similar to the tables that you can create in an idw. A table just like the iAssembly table would be fine, minus the iAssembly part or any sense of configuration.
View 4 Replies View RelatedI am trying to come up with an automatic method to add a new row to my i assembly table and populate that row based on values entered by the user (assuming that combination of values doesn't already exist... ). Basically, I wish to build my i assembly table on demand over long term by user input via a form that calls an ilogic rule.
View 1 Replies View RelatedI have created two iParts, both with corresponding tables which I then put into an iAssembly so I can change the size of a pad eye and two cheek plates depending upon the desired Working Load Limit. I have a very basic form right now with a drop down menu to chose the different Safe Working Loads but whichever one I choose, is not changing the table configuration to the desired size. Clearly my iLogic code is not working the way I would like. See below and also see attached screen shots so you know what I am working with.
If Parameter("SWL") = "4.75Te" Then
iPart.ChangeRow("PADEYE iPART - IMPERIAL:1", "WLL = 4.75Te")
iPart.ChangeRow("CHEEK PLATE iPART:1", "WLL = 4.75Te")
iPart.ChangeRow("CHEEK PLATE iPART:2", "WLL = 4.75Te")
ElseIf Parameter("SWL") = "6.5Te" Then
iPart.ChangeRow("PADEYE iPART - IMPERIAL:1", "WLL = 6.5Te")
[code]........
This code was actually overwriting the table properties (in excel), so I know this is wrong, I just couldn't find any snippet for changing a table configuration .
I have created two table rows in an iAssembly that I would like to have a iLogic code written for.
What do I need to use to trigger between these two, when, for instance, a certain numeric value is entered in the parameters? Within the assembly file, when I use the iPart.ChangeRow (or iAssembly.ChangeRow) and put the . I am filename in the first spot, it says it cannot find the file.
This is what I am using, and the error states it cannot find the . i am file I am referencing.
IfParameter("Window_Cutout_Vertical")<=1AndParameter("Window_Cutout_Horizontal")<=1TheniAssembly.ChangeRow("A60_RHR_Door_Assembly.iam", "A60_RHR_Door_Assembly-02")ElseIfParameter("Window_Cutout_Vertical")>1AndParameter("Window_Cutout_Horizontal")>1TheniAssembly.ChangeRow("A60_RHR_Door_Assembly.iam", "A60_RHR_Door_Assembly-01")EndIf
How can I display iPart parameters in an iAssembly general table?
On my .dwg I would like to use one detail with a table. The 2 table columns I need are:
(1) iAssembly name (no problems here, shows up in the general table by default)
(2) Length (this parameter value is in the iPart)
Inventor RS 2011
AutoCAD Mechanical 2011
ASD 2013
Vault Collaboration 2011
Windows 7 Pro
How to edit the member name in an iassembly table using code? The Part Number and Description iproperties are easy to handle. But I am stuck on how to access the member name and edit it. I guessed at some methods, but keep getting errors.
View 4 Replies View RelatedI'm making my first iAssemblies and have run into a strange problem.
I have the option to add the Table Replace column for iParts, but this option isn't avialeble for parts inserted from content center.
In the column Description from a I-assembly table I will place the text Test<200. Than I get a error message "Detected potentially damaging errors in the table. Unable to interpret cel: " ". It goes wrong with this symbol <. How do i get this symbol normal as a text in this column?
View 5 Replies View RelatedIn a simple case I have an extrusion with some attached seals/weather stripping, all implemented as iParts having their own LENGTH parameters.
RailPart.ipt, Seal_A.ipt, Seal_B.ipt
The goal is to encapsulate these IParts within an iAssembly: RailAssy.iam, where a LENGTH parameter can be input when the iAssembly is placed, causing RailPart and Seal_A to have their length parameters set to the LENGTH provided at that time and SEAL_B having Length set by an iLogic rule to LENGTH - 5.
I've been unable to set up a Custom Parameter Column in an iAssembly table. Is this even permitted?
Inventor Premium 2012 SP1
I've created some buttons and I've exported them as .pngs.
I'm getting an unwanted white border of margin, or padding (whatever you want to call it). how I can get rid of this?
If I try to transform and resize the png it shrinks my buton (which is at the exact correct size).
I have a drawing of a sheet metal part that I did late last year. I used a Hole Table to dimension all the holes.
Fastforward to today. I added two holes that are different in size than any other hole. So when I opened the drawing it automatically added them to the Hole Table and gave them tag #'s in a new group and it kept the grouping in Alpha order. A, B, C were there before and it added D. Great, that's the way to do it.
Then I decided I needed to change the hole size. The change would keep the size different than any other hole on the part still. I go into the drawing and it change the size in the Table BUT, it also moved them up to the top of the list but kept the tag # as D*.
How do I get those two entries back to the bottom where they belong to keep them in order?
In my iAssembly, I have placed a weld. In one of the members, I am suppressing the weld. When I change to that member, I get an error "Weld No Spine: could not compute Weld: Possible intersection failure". Inventor complains a little, but it does not show that Red Cross after the member is selected.
Why do I see that even though the weld is suppressed for that member?
Heres a video of what I'm seeing?
Windows 7 x64 -12 GB Ram
Intel i7-930 @ 3.60ghz
nVidia GTS 250 -1GB (Driver 301.42)
INV Pro R2013, SP1.1
Vault Basic 2013
If I put iParts into an assembly, and then convert this assembly to an iAssembly, I can include "Table Replace [My_iPart]" as a column in the parameter table. As the value of this column I can select the individual rows of the given iPart parameter table.
However, I can not make this column be a "Custom Parameter Column". (In fact it seems to me that in an iAssembly I can not make any other types of columns to be "Custom Parameter Columns" either). Also, if a parameter of the iPart is a "custom parameter", I can not carry over this "customness" into the iAuthor parameter table.
This means that I need to insert table rows by hand, one-by-one, which is quite cumbersome. Imagine you have an iAssembly containing only two iParts, each having N rows. This means N^2 rows in the iAssembly, all of which I need to specify by hand. Plus I can not use the "customness" of a parameter of an iPart within the assembly.
In an iAssembly containing an iPart, I would like to
- have a "Custom Parameter Column" in the iAssembly parameter table, which can select rows from the iPart parameter table (selectable values would automatically be all the rows from the correcponding iPart)
- if my iPart has a custom parameter, I would like to have this custom parameter available as a separate custom-value column in the iAssembly
Is it possible somehow? Or is it conceptually wrong?
I have several iterations of an assembly. Specifically I have a base of a machine with different tooling for different products.
I generated the BOM by referencing the specific tooling I am trying to detail. That worked. But when I balloon, it references the main assembly. It won't let me redirect the source file to the tooling asm.
Issue between an i-assembly and i-Logic. So, I have an assembly that includes some extra components that are not always needed and therefore an i-Logic rule takes the decision whether these will be suppressed or not.
Of course this is not a problem however it turns out that I miss some info from BOM according to the suppressed parts ...and all these makes sense following the LOD etc.
A potential solution to keep up to date the BOM while you are excluding the needless components is to create
an i-Assembly.
To keep that simple I turned my current Assembly to an i-Assembly and very successfully I excluded various components and of course I included some others by adding extra ROWS.
So far So good
Now I want to apply some dimensional boundaries by using i-Logic rules. According to them I want to allow this i-assembly to jump among these different ROWS that meet the right criteria.
Very rough thoughts led me to the following code...
For example...
If Width > 600 Then
iPart.ChangeROW ("..." , "...") 'Row-1'
Else
iPart.ChangeROW ("..." , "...") 'Row-2'
End if
The Problem is that the above code works fine, for a example, in case that I will place an i-part in my assembly... However I am looking to change the row of the actual assembly that as I mentioned before I turned it to an i-assembly
To make this even more clear I want to be able to manipulate my i-assembly with i-Logic rules while this is open in Inv. I don't want to change rows while this is placed as a component or sub-assembly in an another assembly...
I have 2 configurations in my assembly and one of them is in ipn file.
Once inside I cant change members...
Is it possible to change between them in the ipn file?
I was wondering if I'm able to create two tables in an iassembly, like one table for size and another for different components in the same assembly.I have a vague memory of an old assembly having this but I can't find it or it's just a figure of my imagination.
View 4 Replies View RelatedI have an assembly with around 120 variants in it. I am getting a little annoyed having to click the OK button when asked:
"Do you want to save changes to 122.iam" and its dependents"
is there any way to set the default to OK?
(other than setting an electric motor and a poking device up)
I am using Inventor Professional 2012 and I have created complex iparts and iassemblies and I am not able to change the BOM structure of the parts simply because they are intelligent. I require the tables and features that the iparts and iassemblies can create but they are coming up read only and can not modify the BOM information. Is there a way to change the read only aspect of an ipart or iassembly?
View 1 Replies View RelatedWhat I am looking for is a command similar to table replace, but that will allow for a new part to be created based on a user input. This will need to be done at the i Assembly level to an i Part that is placed within the assembly.
The end goal is to have input boxes come up, ask the user for the values then create all of the associated parts.
I don't need anything with the input boxes, just the part creation.
I'm an architect and I'm drawing up a development of 80 houses and I need to provide a Sales Plan which includes the width and length of each rear garden in the development. Rather than show these as actual dimensions on the drawing (which will get messy and make the drawing look untidy due to the large amount of units) I plan to create a simple table with plot number and dimensions.
My plan is to dimension the gardens on a non-printable layer and to insert a field into a table to obtain the required dimension. I've done this for the first few houses but I have to insert one field and then select the dimension to get the "m" dimension and then repeat the process in order to get the "ft" dimension.
My question is is it possible to insert a field (or two separate fields) that will display the dimension once in m (ie 12.80m) and once in 'architectural dimension style' (ie. 41' - 7 1/4") by only clicking on the dimension once??
This will save a lot of time as this size of development is quite common for me.
How we can access the part parameters after hitting create iAssembly. do I need to make i parts first and then bring them to an assembly and make an iAssembly??
View 5 Replies View RelatedI have an i Assembly, with a Sub-i Assembly and i Parts. Is it possible to "extract" a copy of one configuration as normal assembly? So that I have an assembly where I can modify parts without touching the iAssembly or iParts.
View 5 Replies View RelatedI am looking for a way to change the parameters of a part that is within an iAssembly. Basically we have tubing with flanges on the end and wish to have an easy way to model varying lengths. I essentially need to be able to have the upper level iAssembly control the flange spacing and cut the tube to length based on the users selection. Due to BOM setup these parts must be seperate .ipt in a larger .iam
View 2 Replies View RelatedI need use Include / Exclude some components in a Pattern which include an iAssembly. But looks like this option is not available (maybe I missed something)?
I use Inventor 2009, XP32 OS.
Autodesk Inventor Professional 2013 (64 Bit) SP2
Windows 7 Professional Service Pack 1
Intel(R) Xeon(R) CPU E5645
12.0 GB Memory
I have tried to use the command retrieve dimensions for an iPart and iAssembly but no dimensions will appear
View 6 Replies View RelatedA client was looking to develop a custom interface for documenting iAssemblies.
Would it be possible with iLogic to:
1. Show form.
2. User selects a Browse button to select iAssembly to document.
3. List all iAssembly configurations in the form.
4. User picks configuration.
5. Select OK to create base view, projected view, and Parts List.
This may require API.
I'm having an issue with Inventor crashing every time I attempt to follow this exact procedure:
1. I have a drawing open with an iAssembly or iPart in it.
2. I edit a view by double-clicking the view, opening the 'Drawing View' dialog box.
3. I open the 'Model State' tab.
4. In the 'iAssembly/iPart Member' menu box, I select a different member.
Now, it may or may not open the 'Save' dialog box. If it does, then I click 'OK' and poof, Inventor crashes without fail, asking to send in a crash report.
The same thing happens if I start a brand new drawing and attempt to follow the same procedure while inserting a Base view.
Now, I know for a fact that the not all of the drivers are not up to date on my computer, I am not using a recommended graphics card, and I am using SP1.1, not SP2. I have notified my IT guy about this, but he has yet to get back to me. I don't now if/when everything on my computer will be updated. I do not have admin rights to my computer.
In the mean time, Inventor has become essentially useless for me until this issue has been resolved. how I can get these drawings to start working?
I have made a simple iPart with the option to suppress an extrusion. How do I control this in an iAssembly?
View 3 Replies View Related
