If I have a table or custom iPart and create an instance of it inside an assembly, is it possible to create an independent .ipt file which is not linked to its source file?
View 2 RepliesHow to create a .idcl file for an i-part.?
send me procedure for publishing the file.
I have facing issue to link the ipart members in to the new part.
for example, i have one machining part that machining part showing make from number. so, i created make from first. it has 10 instance.using iPART i created 10 members.after that i need to be do the machining.machining drawing also having 10 members. How i call the each make from members in to the machining model.
We are using Inventor and Vault pro 2013.
I have an iPart in which I want to change the File Name Column from "Member" to "Part Number". These columns are not the same and makes the filenames for the members different when generated.
The challenge is that I already have about 100 members generated and used in different assemblies. I want these to be replaced by the new files and be deleted.
If I change the File Name Column I will get 100 new files (ipart members) that is not used anywhere. The only way I know of to replace the 100 "old" members is to do this in Vault - one by one..
I have a unique challenge. I use my personal laptop for my CAD work at work. We are now setup with Vault 2012 and Inventor 2012 and we are setup to pull our Templates, standard files and content center parts from the vault.
I have become so busy that I would like to do some of my work at home on evenings and weekends. Other than the obvious problems of having no life and working for nothing, I am having the problem of not being able to access templates or CC parts at home. I can store the CC and templates on my C drive but am not sure where to set Inventor to point to the files on my drive or if there is an easy to do so depending on where I am.
I read what is in the picture in a skill builder, which is:
[URL]
When is a sketch that is copied to another part file linked to the source file?
I tried it, i copied part of a sketch, some lines, from one part file into a sketch in another part file and there was no link
Error 1308 Source File not found inventor professional 2013
View 1 Replies View RelatedA part of an application I'm writing involves detaching a specific xref of known filename and path from an open drawing. I'm having a surprising amount of trouble figuring out how to do this or finding any examples "out there" (A'desk forum, the googles, A'desk developer's guide). I have the code for attaching an xref, but detaching is presenting unexpected problems.
View 6 Replies View RelatedWe prefer to detach all xrefs when exiting a base file instead of unloading them. Is there a way to have autocad remember which xrefs were used in the base file so that they can be reloaded all at once next time.
View 4 Replies View RelatedSetting up a tabulated ipart drawing template. Which is better...one drawing file with a table or individual drawings for each tabulation? Also does one method work better than the other when introducing vault?
View 1 Replies View Relatedtoday i downloaded gimp 2.8.2 for windows 8, but when i tried to run the installer it downloads halfway and then displays an error message.
it says something in the style of: An error occurred when trying to copy a file. The source file is corrupted.
What exactly is this tool used for if you cant change the source file name or the path? and why would the interface let me poke into these fields and give me the option to find and replace if they cnnot be edited
So how can I change the Source File name and path?
Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
64 Bit Win7 OS
How do I change the BOM structure of iParts from Normal to Purchased? The BOM editor in the assemblies that use the iParts have the iParts as read only. I can't find a way to change them to purchased from inside the iPart either.
View 3 Replies View RelatedIs there a way to add an iPart column to the iPartTableColumns collection? I'm using Inventor 2009.
View 5 Replies View RelatedI've made a component pattern in an assembly using an iPart. The iPart as several different lengths, but I cannot switch lengths in the assembly. In other assemblies, right clicking on the Table icon allows me to change lengths, but this assembly will not.
View 2 Replies View RelatedIn C++ can I use this function, using the key index Member string to select which row in the factory I want to insert?
In the docs all I see is Use an iPartTableRow (but no examples in C++).
Use an index, this works but I need to know the index before using it.Use a set of parameters in a string (but "[Member=142314]" does not seem to work. Can I not simple use a string with the appropriate member?
its possible to UN-author an iPart?
View 7 Replies View RelatedI want to insert a row which contains data into iPart as new part member but without using excel.
View 3 Replies View RelatedHow to set cute pdf to always auto print in same directory as source file. Also use source file name except with .pdf extension. I would like to add a macro to my save button so it does this automatically and never have to convert again. This would also be useful for dwf format also. Disk drives are massive now so no need to save space.
View 3 Replies View RelatedI'm having a problem opening AutoCad Civil 3D 2010.
When I click the shortcut Windows starts configuration and then I get the following error message:
Error 1308.Source file not found;C:autodeskAutoCAD Civil 3D 2010
x86C3DProgram Files
ootCommon Files FolderAutodesk
sharedAdLM|R1en-UShelpBRWstylecommons.css.old.
Verify that the files exists and that you can access it. Needless to say AutoCad wont open all I get is Retry or Cancel, selecting.
Retry just gets the same error so when I Cancel I then get "Are you sure you want to Cancel" which I select and then I get the message Fatal Error during installation.
This is a downloaded install from Autodesk and I dont have discs available.
DWG TruView,Autodesk Vault 2010 and Autodesk Design all installed OK.
System detail's; OS is 64 bit Windows Home 7 Ver 6.1.7600 with IE8
CPU AMD Athlon 11 P320 Dual Core, 4 gig RAM,500GB HDD running on a new Toshiba Laptop.
I've looked around at various forum's without success.A couple of sites offer what they call a fix but it turns out to be registry scanners.
How do I rename an iPart member name? Can I use Design Assistant?
View 2 Replies View RelatedCan I use diferrent types of threads (as variants), in one iPart/iFeature file, ex. M10x1.5 (ISO Metric profile) and G1/8" (ISO Pipe Threads)? Look at the file in attachment and correct it if possible.
View 2 Replies View RelatedI have created an ipart and want to create a right hand and left hand option of that part. I can mirror the features involved and suppress the mirror feature for the the RH part and so the RH version looks fine.
BUT if the mirror feature for the LH version is in the compute state I get both handing showing. How do I suppress one handing and leave the other for my RH version.
Is it possible to add a Appearance tab to a Ipart table? I am cataloging a set of parts and one part is made with steel but in Gloss - Black and Matte - Black and i'd like to differentiate the 2 without haveing to make 2 seperate Ipart files.
View 2 Replies View RelatedI have listbox that shows ipartname of one ipartfactory it would like and me that when selecting one of them it could send to the assembly ipart selected hear show code.
Dim InvApp As Inventor.ApplicationSet InvApp = GetObject(, "Inventor.Application") Dim IpartSeleccion As ipartMemberSet IpartSeleccion = listbox1.Value Dim oDoc As AssemblyDocumentSet oDoc = InvApp.ActiveDocument Dim oOccs As ComponentOccurrencesSet oOccs = oDoc.ComponentDefinition.Occurrences
[Code] ........
I have an ipart but I can't for the life of me get them to be in order, small to big in the browser.
I have them in order in the table but they are mixed up in the browser.
Is there a way to do this.
see attached picture
I'm trying to take multiple parts of the same type and make them into one .ipt I began doing this and It seemed to be working fine. When I put those grouped .ipts into an .iam, Inventor creates a Subfolder of each .ipt and fills it with each part from that group and now those created ipts are unique unlinked parts (unlinked to the group ipt). I'm trying to reduce our file count and link our .ipts and .idws/.dwgs so this Inventor file creator results in the opposite of what I'm looking for. My question now is is there any way to modify this process to work the way I need it to or is there a completely different way that I should be doing this?
View 4 Replies View RelatedHow can I get the iPart information in a partlist.
I have a tupe DN 25 iPart where I can control the length, and i'll like to have a text I description field in my partlist that says "DN 25, Length = <actual length>".
the newest model I have made I have run into some troubles. When I switch between one member and another most parameters update correctly but the part is still requiring an update before the finished part is created.
When the feature small sheds is enabled the pattern isn't working correctly.It seems as though the height that controls the sheds is not updating during the member change process and is causing the pattern to be the wrong length.
I have set up a form to add my parameters as there are a large number in the ipart table.I can't generate my member files as they show the member before it is updated and is wrong.
Is it possible to show surfaces in a drawing view of an ipart member - although the option of include all surfaces is there I can't get them to show. Similar issue with showing sketches - get model sketches is there but nothing can be shown.
View 2 Replies View RelatedI need an ipart for helical gear.
View 9 Replies View Related