I want my browser name using iLogic particular change to the part number. I fill in my iproperties, the part number. Then the browser name has to take over the part number.
But i get an error.
doc = ThisDoc.Document
Dim oCC As ComponentOccurrence
For Each oCC In doc.ComponentDefinition.Occurrences
OccName = oCC.Name
oCC.Name = iProperties.Value("Project", "Part Number")
Next
I need to make installation plans on climate ceilings, which are steel cassettes with Meandro tube element located where cold or hot water is flowing through.
[URL]......
Now it may occur that a cassette is given a code 700 which represents the type of cassette. If inside the cassette is placed a Meandro element its become a follow number eg 700-01.
It may also be that the same cassette No. 700 gets another Meandro element and because the cassette has not changed shape the number 700 remains the same but the follow number change e.g. 700-02.
At the moment I change the number in the browser,(inv2012) I therefore want automatically the iproperties ,partnumber and stock number, to fit. When I go to the BOM, the part- and stock numbers automatically will be placed.
The browser codes are not displayed in the BOM. So if I specify for change I only have to do so in the browser. I wanted to do so by iLogic but then ran into problems. I found a tutorial from Rob Cohee with ilogic so you won’t forget to fill in your iproperties.
[URL].......
I also wanted to do so with the iproprtie Stock number but get an error stating that I must declare the name. How must i declare a name.
Also i was told for entering the browse name in ilogic i had to use displayName, but I get a error stating that the name is Read Only.
So how can i, after i change the browse name, automatically fill in the iproperties ‘part number and/or stock number? Is there an ilogic code for?
How can I change the default icon that shows up in the browser node in a part file? I found some VB code but can't seem to get it to work with ilogic.
View 7 Replies View RelatedI want to be able to have All Work Planes set as 'Invisible' but create a Message.box or Icon that allows me to change the Visibility of any individual workplane(s) physically selected in the browser.
A rule written by another member should do the trick if the following line could be altered so as not to read 'For Each' oWorkPlane but instead for 'Each Selected' oWorkplane.
'For Each oWorkPlane In docFile.ComponentDefinition.WorkPlanes'
'get user input
oInput = InputRadioBox("Select workplane visibility:", _
"Turn ON workplanes for all components", "Turn OFF workplanes for all components", "False", "iLogic")
'Define the open document (top level assembly)
Dim openDoc As Document
openDoc = ThisDoc.Document
[code]....
I have one doubt i have one big assembly in that more than thousand parts.
my doubt is how to find particular part in browser bar.
like how to search particular part number in browser bar.
I was just wandering if there is any possible way to get the DWG NO. (part name in our case) to link the the Sheet Name in the Browser window?
View 3 Replies View RelatedWorking on a product configurator using iLogic and have a large amount of hardware that needs to be suppress or unsuppressed based on certain parameter choices. Instead of creating hundreds of lines of code suppressing and unsuppressing the hardware one by one, I was hoping to put hardware into folders based configurations. In my mind this would have allowed me to have one line that would suppress the folder as needed. Unfortunately I cannot figure how to suppress a folder in iLogic as I saw someone else mention I was hoping for a "Folder.IsActive" rule but have yet to find one.
Inventor 2013
how to create an iLogic rule that automatically renames the browser nodes based on part number. I know that this is a function in Inventor itself. The problem is that there is no built-in functionality to automatically change the default browser name to something besides part number. I've done a lot of digging and I came across the following code from an old thread discussing Inventor 2011. I am interested in 2013. It is also worth noting that when I run this code, my Inventor crashes.
PrivateSubMain
UpdateAssyBrowser(ThisDoc.Document)
End Sub
[Code]....
When I replace elements with iLogic the Inventor Browser is not automatically refreshed.
E.g. I have a file A.ipt and I replace it with B.ipt then in the Brwoser will be shown: A.ipt:1, even when B is already inserted.
Is there some refresh, like "Update Browser nodes when done" ?
These both has no influence on it:
iLogicVb.UpdateWhenDone = True
InventorVb.DocumentUpdate()
By the way. To Update the Browser manually, I have to rename the block nodes (From Filename to Filename). So it's only opening up the Renaming Function and then hitting "ok".
If there's no direct function to update the Browser, maybe there's a way to do the manually way by iLogic?
I'm trying to create an ilogic rule that will look within the folders of an assembly and take the contents of each of those folders and demote them to separate sub-assemblies.
ie. Assembly1 contains NewFolder 1. NewFolder 1 contains Part1:1 and Part2:1. Upon executing the ilogic rule, I would like Assembly1 to contain NewFolder 1 and within NewFolder 1, Assembly1-01. Assembly1-01 contains Part1:1 and Part2:1. I would like this ilogic rule to look within each successive folder within Assembly1 and demote them according to their position in the browser such that NewFolder 1 - at the top of the browser list - contains Assembly-01, NewFolder 2 contains Assembly-02, etc.
I currently copy a master assembly with browser folders that contain parts and sub-assemblies to a secondary assembly where I manually demote the contents of the folders to sub-assemblies. When I create a drawing for our machine assembly department, the demoted sub-assemblies to isolate only those parts - nuts, bolts and the pieces they fit to - so it is easier for the assembly department when putting a machine together.
Is it possible, using ilogic, to demote folder contents to sub-assemblies with an assembly document?
I would like the size of bearing to be included in addition to existing data to the File name, Part number and Browser name like for example the DIN 625 T1 does. I have copied the DIN 625 bearings to the custom library. I have added required info to File Name building and to the Part Number building in the custom library and now my Filename and Part Number are as I like to.
But I cannot find how to force the Browser name to be equal to Part number or File Name? [URL]
I am looking to apply a set part number iproperty to the first, then second, then third components in the assembly browser tree in my iLogic rule, regardless of their current part number. (I need to select them by their position in the browser tree as their part number will vary). How do I do this?
View 1 Replies View Relatedis it possible to rename the browser node on part level with an iLogic rule? I know that in the assembly environment is an Inventor OOTB functionality to rename the nodes to the filename, Part number or the default value.
Inventor Professional 2011
Windows 7 Enterprise 64bit
Dell Precision M4500
Intel(R) Core(TM) i7 CPU Q 820 @ 1.73GHz
8 GB RAM
How do I need to write the code in Ilogic to find the sin of a number. It works fine in a parameter as sin (43) but does not give the same value in ilogic.
View 1 Replies View RelatedMy question: We want to use iLogic to save a PDF-file of the DWG-drawing every time we hit "save". We now use the following iLogic
Spoiler (Highlight to read)oPath = ThisDoc.Path PN = iProperties.Value("Project", "Part Number")
PDFAddIn = ThisApplication.ApplicationAddIns.ItemById("{0AC6FD96-2F4D-42CE-8BE0-8AEA580399E4}")
oDocument = ThisApplication.ActiveDocument
oContext = ThisApplication.TransientObjects.CreateTranslationContext
[Code] .....
Im linking a prompted entry in a sketch symbol to a selection from the user in an array. The code works perfectly.
The array displays the number of sheets there are in the document, the user selects the correct one & the sheet number is displayed in the prompted entry. I need to add "SHT" before the number though in the code but I cant get it to work.
I dont want to add a text line into the symbol saying "sht"
Dim oApp As Application: oApp = ThisApplication
Dim oDoc As DrawingDocument: oDoc = oApp.ActiveDocument
Dim oSheet As Sheet: oSheet = oDoc.ActiveSheet
'This uses a sketch symbol with the name "'View On' View Label"
Dim oSymDef As SketchedSymbolDefinition: oSymDef = oDoc.SketchedSymbolDefinitions.Item("'View On' View Label")
'This is the selected view
Dim oView As DrawingView: oView = ThisApplication.CommandManager.Pick(SelectionFilterEnum.kDrawingViewFilter,"Select View To Place Symbol:")
'This takes the label items of the selected view
'And adds it To an array that will link To the prompted entry
Dim sPromptStrings(2) As String
sPromptStrings(0) = oView.Name
sPromptStrings(1) = oView.ScaleString
oDoc = ThisApplication.ActiveDocument
Dim sSheet As Sheet
'create sheet number list
Dim oSheetList As New ArrayList
i = 0
s = "-"
For Each sSheet In oDoc.Sheets
i = i +1
oSheetList.add(i)
Next
oSheetList.add(s)
'get user input
mySheet = (InputListBox("View taken form sheet number.", oSheetList, oSheetList(0), "Sheet Number Ref.", "Sheet Numbers"))
sPromptStrings(2) = mySheet
'This is the position for the sketched symbol under the selected view'
Dim oPosition As Point2d: oPosition = oView.Center
oPosition.y = oPosition.y - (oView.Height / 2 + 2.5)
'This inserts the sketched symbol and fills in the prompted entry.
Dim oSymbol As SketchedSymbol: oSymbol = oSheet.SketchedSymbols.Add(oSymDef, oPosition, , ,sPromptStrings)
I am making a iPart with iLogic. I need a function to convert letter to number or convert number to letter as we did in VB for Excel.
For example: Char(65)="A"; CODE("A")=65, and so on.
I have made a configurator, that defines my part. Now i would like to add some intelligence for the Save process...
When i activate my rule it should.:
1. Go to a Excel spreadsheet and find next Empty cell in a specific collum
2. Place Title from inventor in that empty cell
3. Return the value from the cell next to this cell
3. Use this value as the new filename for my part.
Example: here i would like to get the parts tile put into B3 and A3 (103) returned to Inventor as filename to my part
--------------------
A B C
1 101 Title1
2 102 Title2
3 103
If possible, i would like to be able to adjust this alittle as i go forward in my work,
I need to use/write a iLogic code. I have a assy, in this assy i have parameter Height and Width. And it´s no problem to controlls this two rules/value.
But I have a problem with the rule when my height will control the number of parts
If my height is 500-1000, one part.
If my height is 1000-1500, two parts.
If my height is 1500-2000, three parts.
Is it best to use suppress or use a pattern in this case?
I dont no in english if odd number is the right word but i want to make all my number to 1, 3, 5, 7, 9, etc,....
View 9 Replies View RelatedHow to reference the drawign sheet number using iLogic? I see on the snippets on the side a way to reference the sheet name, but I only want the number. To get the name it is ActiveSheet.Name, but ActiveSheet.Number does not work. Getting the name give something like ASSM:1, so if there was a way to take that and subtract the colon and everything before it that would work also. I am not a programmer, I've just taked some programs I found online and modified them a little to do what I want to do, but this is holding me back a bit.
Overall, I'm trying to modify the drawing view label to have a project number, referenced from the drawign iProperties, a view label, and sheet number, and then save that info in an iproperty of the part, and then reference that in the BOM so it automatically labels all of the views and fills out a column of the BOM to reference which page and view to find the parts of the assembly. I have everything working except for the sheet number.
I would like to have the part number automatically be entered with ilogic.
Normally I know how to do this but this time I'm trying to have a couple constant letters with numbers to be filled in.
Example
MGR72
MGR is constant and the 72 will change with the width
What I thought would work but doesn't is
iProperties.Value('Project", "Part Number")="MGR" Width
I'd like to create a part number generator using iLogic. The rule would run as follows:
If the iProperty "Part Number" was not blank or the same as the file name (as Inventor default), then a question box would pop up asking if you would like to overwrite the part number. If one were to select yes, then the following would happen.
iLogic would open an xls that is on the network. The xls would have two columns. Column A would be the part number, B would be the filename associated with that part number.
Column A (the part number) is a sequential count in the form of 6 or seven digits. The format would be something like =TEXT(ROW(A1),"JFRC-000000")
Everytime the part number generator rule is triggered, it would create a new part number on the next blank row, copy this part number to the Part Number iProperty and assign the file in which the iLogic rule was executed to column B in the xls, save and close.
If, when the rule is triggered, the Part Number property is blank or the same as the file name, the user would not be asked if they would like to overwrite the part number. This rule would be triggered manually from a form.
iLogic rule that will retrieve a part number(s) from an excel sheet. I work for a company that built vacuum trucks and I'm trying to make an . I am template where the user can select different lengths of shells to achieve the desire overall length. I have been able to achieve this using iLogic rules and forms and making the shell length parameter multi value.
But now I need to show predetermined SAP part numbers for the shells in BOM or part list. I all ready have an excel sheet with shell sizes with corresponding part numbers on file. I also thought about incorporating our custom CC parts/shells that already have the SAP part numbers set up as a custom iProperty but might be to complicated for a newbie iLogic user.
I have a part number that i want to defined in custom properties.
Then would it be possible to call it out in Ilogic? that way in any drawing doesn't matter where the part number will always be the same for that part when i balloon and the same in the BOM.
I am using ilogic in Inventor 2011 to update my iproperties when I save a .dwg file. I am having problems with some custom iProperties I have created that are of the type 'number' and are initially set to 0 (zero). After the iLogic rule has run and the user has entered a numeric value the type of the custom iproperty has changed to 'text'.
The ilogic code I am using is:
If iProperties.Value("Custom", "Nominal ID") = 0 Then
iProperties.Value("Custom", "Nominal ID") = InputBox("Enter The Nominal ID (Enter 0 if no value is available)", "Nominal ID", 0)
Custom_iProp_Nom_ID = iProperties.Value("Custom", "Nominal ID")
End If
I am using Vault 2011 and would like to map this property to a numeric property so I can perform <= and >= searches.
I have two user parameters saved in a part template that are tied to the part volume and an overall estimated part weight. The user parameter Pc_Volume is the volume in cubic feet and calculated by pulling the part mass (in cubic inches) and converting to cubic feet via ilogic rule. This is then automatically run via event triggers before a file is saved and if the part geometry has changed to keep the volume up to date. These are exported because they get pulled into iproperties of our drawing files as well as used to create a parts lists showing the volumes and weights.
I have the property formats of the user parameters set to Number and to unitless and the unit display turned off so it does not show on the parts list, with a precision of 0.000 for Pc_Volume. The Pc_Weight is set the same way however with a precision rounded to the nearest whole number.
These are created this way so when we use the part file as the template when we select "Make Components" to separate our parts and tie them to an assembly all the files are then updated and the information saved for exporting.
The problem is, the Pc_Volume always comes in rounded to a whole number. The Pc_Weight Does as well, but that doesn't bother me since we want it to do that anyway. If I would go into the part file after it's created, double check the precision and then re-run the rule the volume will show up with the correct precision in the exported parameters. I don't want to have to open each partfile however to get this to update.
Attached are images of the parameters, ilogic rule, and exported results.
I had wanted to find a way to engrave/emboss the part number on a part model and have it be parametrically tied to the part number iProperty. Since it doesn't appear that I can create a text box and insert the iProperty directly, here's what I did to work around this. (I setup my part templates to have this out of the box....)
1. Within, the IPT file, add a user text parameter called "PartNo" and set its initial value to any text value.
2. Create your sketch for your text to be engraved. Insert the User parameter you just created.
3. Create the engraving/embossing for your text.
4. Create the following iLogic rule:
' Requires a User Text Parameter called "PartNo" prior to running' Set the appropriate event trigger to tasteIf Parameter("PartNo") <> iProperties.Value("Project", "Part Number") ThenParameter("PartNo") = iProperties.Value("Project", "Part Number")InventorVb.DocumentUpdate()End If
5. I set this rule to fire using the "iProperty Change" event trigger. So if the iProperty is set or changed, your text will update. Obviously, you can set this to run with whatever trigger you like.
Inventor 2014 64-bit SP1
Win 7 Pro 64-bit SP1
is it possible to change browser folder icon?
View 7 Replies View Relatedline of Inventor 2013 iLogic that can change the browser node name of an IDW?
Specifically, I'm only interested in changing this:
I know how it's set by default, but someone has managed to fix their template so it only ever shows "A3 template" in this field. consequently, this problem now persists throughout hundreds of drawings. If I can fix it with a line of iLogic, then the wickedly awesome CodeInjector can be used for fixing all the drawings.
Is it possible to make iLogic rule to do this:In dwg Place part and in Browser to see part name without extra typing. Not Sheet 1 sheet 2 etc.
View 9 Replies View Related