I have a tube which I'm adding a pocket to the outside by removing some material. I then need to array that around the tube. However I need to offset each pocket along the length of the tube. I've attached the tube with one pocket (v2013) and a picture showing the pattern if the surface of the tube was unwraped.
Is there a way to unfold a coil shape to get the flat pattern? When I try to unfold the attached part I get an error message (see attached error_msg.jpg). We have been using AutoPOL to unfold these kind of shapes (which works fine). But since we have a very old version which we really need to upgrade, I was wondering if nowadays Inventor could handle coil unfolds.
If this will not work with the current IV2013 release, will this then be implemented in a future release? Are there any alternatives or should I just go for the AutoPOL upgrade?
Is it possible to take a feature created by a pattern and reuse it to create another pattern? I have a circular part on which I have created a linear pattern (using the rectangular pattern feature) of holes, 6 in total listed as 3 ccurrences. if we number the holes 1-6, I would like to make a circular pattern based off holes 2 and 5. I have been unable to figure out how to select the individual "occurrence" related to the hole once in the pattern feature. If I create the circular pattern first and then the linear and try to suppress the others it supresses both holes in the occurrence.
I am creating an assembly with my base part being a weldment. I've added other components that mount to my base part. Now I need to add fasteners to the mating components. I have added my first fastener and now want to pattern the said fastener using the "Pattern Component" and by using the "Feature Pattern Select" option and selecting "Associated Feature Pattern". At this point I have already selected the component that I want to pattern and selected the "Associated Feature Pattern" to select my base pattern. The only problem is that I am unable to select the pattern desired.
A note on how my Weldment was constructed -The holes were created in the "machining" step of the weldment, not in the individual part before it was placed in the weldment assembly.
If I move the hole feature and its pattern to the individual part and then place it in the weldment assembly, I can then create an "Associated Feature Pattern" in my assembly file.Why can I NOT create the associated pattern when my hole features are created in the weldment assembly? Or am I missing something?
I have attached a jpeg file of a Plate out of a heat exchange.It shows half of the Plate but it is identical shape for top and bottom.I am able to create the solid shape but i need creating the numerous patterns onto the plate.How would i place the pattern feature onto the Plate?
Also from the picture there is a gasket.Would this be made as a separate part and placed on the Plate in a assembly file?Would the gasket be best made using sweep function?
I have created the plate as a solid model but would Sheet Metal also work or even be a better choice?
While using the Circular Pattern feature or rectangular pattern feature in Inventor, sometimes I want to extrude (join) or cut the drawings that I made (augmented) with using circular pattern feature, rectangular pattern feature. in this case do I have to choose all the augmented members one by one (for instance I make 42 augmented members), it can take a lot of time. also after applied any of these features I can't use trim feature, can I ? but sometimes using the trim feature after applying the Circular Pattern feature or rectangular pattern can be necessary.
How to pattern a feature along a spline curve so that the resultants are separated by an equal linear distance (chord length), rather than as a function of the spline curve's length?
I have a Hole that cuts through 2 solid bodies, a gasket and a cover plate. I want to pattern the hole in BOTH solids at the same time, but the pattern feature dialog box will only let me select one solid at a time. I could pattern the hole in one solid before projecting to the other, but the quantity of the holes can change. When the quantity of the holes changes only the holes from the initial pattern are projected. For instance if I have 10 hole initially and it increases to 12 the 2 new holes do not project to the second solid body.
I created a partial sphere with six features on the surface of the sphere. I then applied a circular pattern to each of the siz features. I called the features r1, r2, ..., r6.
r1, r2, r5 and r6 worked as expected. there are 16 features evenly spaced around the surface.
r3 and r4 are different in that the original feature is missing after applying the circular pattern.
each of the six features is as identical as I could get them. I followed the same build seauence for all of them.
each feature is made up of four objects - cut1, cut2, sweep and dimple. I selected the four objects for a row, then applied the circular pattern.
If I delete the circular pattern for r3 or r4, the original feature becomes visible again.
So, why are r3 and r4 behaving differenly than the other four?
I have tried a number of things, including re-drawing feature r3 from scratch with no change in teh results.
Following on from my post regarding a sheet metal component that was unable to create a flat pattern due to creating the component in an assembly; URL....I have found out that it wasn't the in place component that was the problem it seems to be the loft and sweep feature that cause this problem. I have thought about using the extrude feature (as this works) to create the shape and then cutting the ends to get the angles I want but that would be time consuming.
I have set up the sheet metal rule to be 3mm mild steel, any way creating this component and being able to create a flat pattern.
We are using Inventor 2011 and I would like to make a small app that allows my users to graphically select one or more occurrences of a rectangular pattern feature Then allow them to suppress them if desired.
I have determined the code to loop through the pattern occurrences and toggle suppression for any instance. What I do not know how to do is determine which occurrences have been graphically selected.
At this time I am only concerned with round hole features. (Perforated metal)
I'm trying to flatten a section of sheet metal so i can get a cut lenth for my fab shop. Please see attached drawing. I want to use these dimensions, and then flatten the part so my fab shop can trace it and cut the sections, bend them and weld together, but when i use the flatten command, nothing happens..
Is there a way to use the coil command to make a spiral out of a rectangle where the thickness of the rectangle starts at one value and ends at another? This would be a spiral torsion spring with decreasing thickness approaching the center.
what the 2D or 3D equation curve for a parabolic spiral, otherwise known as a Fermat's spiral would be? I have found this info but do not know how to apply it:
Fermat equation
Therefore in terms of the affine plane its equation is The Fermat curve is non-singular and has genus
I need a path on a sphere like on the image I attached (sphere_spiral) for the result similar to image called "gomb". The only problem, metric spiral or coil / 3d helical curve path won't work because it doesn't end the result I need, because the lines are converging each other. So, I figured out I need a logarithmic spiral 2D sketch or maybe a sinusoidal path.
I need a path from the sphere's top center point to the bottom center point, projected to its surface with equal distance of lines.
How can I make a circular pattern of a single occurence of a rectangular pattern?
A shaft has a rectangular pattern of holes (along its axis) on its surface. I want to pattern the 4th occurence of this hole pattern as a circular pattern? Can I do it in Autodesk. I can not select the a specific occurance of a patterned feature to pattern it again.
As you see in the template photo (the photo was scanned by Microsoft Security Essentials, healthy) I wanted to extrude my circle, and I made 28 pieces with circular pattern feature; now, do I have to choose all the pieces by one by to be able to choose all?
The sum of the problem: while using the Circular Pattern feature or rectangular pattern feature in Inventor, sometimes I want to extrude (join) or cut the drawings that I made (augmented) with using circular pattern feature, rectangular pattern feature. in this case do I have to choose all the augmented members one by one (for instance I make 42 augmented members), it can take a lot of time.?
I have an assembly which I am using as a icopy component. In the assembly I have the adaptive sketch which os used for the icopy function and a part which is adaptive to the sketch. I then have the part pattern itself in the assembly. The problem is the pattern will not update when changes are made unless I edit the pattern. The pattern references parameters from the sketch so that when the sketch changes the pattern should change. It works but the pattern will not update unless i open the pattern to edit it. Is there a vb function which will force the pattern to update when a change is made? I tried the update document vb functions but no change. I will try to get a sample together that is a smaller file size so you can see what I am talking about.
I am trying to export geometry found in a flat pattern sketch overlaid onto the flat pattern.
Since I am creating the output file manually I gather the flat pattern boundaries and bend center lines for output to a file.
When I add flat pattern sketch entities to the mix they do not overlay properly. What matrix would I have to push the sketch entities through to get them to the same coordinates as the flat pattern?
I have been working with some GIS data in the form of SHP files in autocad map 3D 2011. On one of my layers I have started getting "Feature was not saved in the target feature source" when I try to check in my data. In total there are 308 errors in the data table, all of which were features I deleted. They all have a featID of null and I cannot remove them from the data table. I need to fix these errors without going back and starting over.
I am running Autodesk Map3D 2012 and I need to label my feature points no matter if they overlap or not.The Map3D documention refers to a check box that will allow what I believe I need- but I cannot find the checkbox in the style editor. Here's a clip from the Autocad documentation:
To allow labels to obscure points on the selected layer..In the Display Manager , select the point layer. Click the Style button.In the Style Editor, click Allow Other Labels To Obscure Feature Symbols On This Layer.
I'm trying to use the cut across bend feature on a sheet metal part. However, when I check cut across bend, it grays out all of the other cutout options, and only has thickness as the only option. This is perplexing to me, because I can't think of too many times I'd need this option other than when there is more than one thickness of material I need to manipulate the profile onto.
I was to understand that this "cut across bend" is for use similar to the "normal cutout" command in solid edge? Keeps the cut perpendicular to the sheet face in a sheet metal part.
Cybertron PC Intel Core i5-3470 CPU @ 3.20 GHz 3.60 GHz 16.0 GB RAM Windows 7 Professional 64 Bit 3D Connexion Space Pilot Inventor Professional 2014 Autocad Mechanical 2014