AutoCAD Inventor :: Planes Visibility
Oct 15, 2013
I have 2 problems:
1. created a turbine whose blades are made from some planes that I applied thicken offset command. I applied circular pattern to multiply the blade around center point but i get too many planes and i must to make invisible each one. How can i make invisible all planes in the same time.
2. After i make them invisibile i exit from that part but when i start that part again or when i place it in an assembly all planes are visible. What should i do to make them invisible for ever.
View 2 Replies
ADVERTISEMENT
Sep 27, 2012
My model is up in the top right of the planes. I cannot figure out why my origin planes are oversized like this. I have went through the browser and checked all the parts to see if something is out there, nothing. I have set auto-resize on origin planes and yet these are large.
Dell XPS 8300
Intel(R) Core(TM) i7-2600 CPU@3.40GHz
16GB RAM
Win 8.1 Pro
Autodesk Product Design Suite 2014
View 9 Replies
View Related
Dec 17, 2013
I just installed inventor. When I begin a part there is no display of the planes, only the corner indicators show up when I hover over a plane. Also, when a part is created, only the edges show up when I hover over them.
View 4 Replies
View Related
Nov 13, 2013
recently installed inventor pro 2014 on a school computer for a project we are doing, one problem. when i click 2D sketch nothing happens, so i have no wau to make a sketch.
View 2 Replies
View Related
May 15, 2013
In a part file is it possible to find the adaptive workplanes used to create extrusion1. And then find if the two workplanes are at an angle with respect to the origin planes.
Have been looking for a while but it seems hard to find information on workplanes
View 4 Replies
View Related
Apr 10, 2013
I've created Custom properties, parameters, to get the outside measure of the parts and it works fine until we create and leave activated a work plane outside the part so it measures not until the end of the part but until the plane.
View 9 Replies
View Related
Sep 6, 2013
Isn't this an important part of sketches? Why would I not be able to project a work plane.
Cannot project any w-planes whether default or created in inv2013.
View 9 Replies
View Related
Sep 11, 2013
i have assembly and i want make drawing of part of it. Part of assembly i want to show/draw is between two parallel planes. How can i do this?
I'm using inventor 2010.
View 2 Replies
View Related
Jul 13, 2012
is there a way to auto project datum planes that are square to the sketch?
View 4 Replies
View Related
Apr 25, 2012
Can extrusion-1 be shelled between the 2 work planes?
View 4 Replies
View Related
Jan 2, 2014
Is there a way to insert a part that would be grounded or flush constrained on one or two planes only (automatically) and not all three? For example; you'd insert the part and you'd pick the two planes that you want to be flush constrained but the 3rd plane you'd constrain yourself.
View 2 Replies
View Related
Apr 27, 2012
I want to create a solid using VB and loft definition.
I creat each time different planes that have a constant distance in x dimension and a steady rotation each time φ (deg).
On each each plane i sketch the same profile and that is happened for 360 deg.
The problem is that Loft is not made because a line of the profile must follow a line tragectory and all other points must follow a circular tragectory. Also, there is a problem from 180 deg to 360 because there is intersection of profiles.
The result must be a solid similar to snail shell but all the same solid, as a cylindar whith a half sphere in the bottom.
View 2 Replies
View Related
Nov 29, 2012
In my assembly I've set up angle constraints between 2 Plane's of 2 parts (min: 40 deg max: 160 deg). If I move the parts slowly the angle constraints holds but if I swing it hard sometimes it flips and gets out of the angle constraint.
View 2 Replies
View Related
Nov 19, 2012
I have found after my last save, the Datum Planes of the assembly have just lengthened in two directions monstrously for no reason. I checked to see if it was an unassebled straggler but cant find anything. Is there a way of knowing why it does this.
Check attached image, the dot is a machine 20 metres high and the datum plane seems to reach the nearest neighbourhood for some reason.
View 2 Replies
View Related
Aug 21, 2007
Ive started at a company where all of their parts and assemblies have all of the work planes, axis and points visible. Im getting bored of going view, object visibility, turn off all work features everytime i open a new model. Anything written that will turn off these features and only turn them back on when requested.
basically im looking for a shortcut, rather than opening every part and assembly and doing it manually.
View 9 Replies
View Related
Nov 20, 2012
The problem I'm having, or what's annoying, is reappearing (visible) Work Planes. I have a number of parts in my assembly that I make invisible and visible on a regular basis and I find that when I make a part visible, the Work Planes of that part also become visible. It's very annoying and time consuming having to turn off the Work Planes when there's no need for them to be visible.
Is there a way to either make all Work Planes invisible or to permenantly make Work Planes invisible unless you specifically make them visible.
View 4 Replies
View Related
Aug 12, 2013
Any time I create a new sketch in my assemblies, all of a sudden every existing work plane toggles from "invisible" to "visible".
In small assemblies, this is fine, but in 100+ part assemblies, it is a major headache. I don't want to turn off work planes every time I make a new sketch.
Is there any way to disable this "feature"?
View 3 Replies
View Related
Feb 15, 2013
I'm trying to re assign XYZ planes after the drawing is complete. I understand changing the view cube etc, but I need to change the sketch itself to match the view cube to set up machining on our CNC and minimize material waste.
View 3 Replies
View Related
Mar 28, 2013
Is it possible to turn of created work planes within a 3d model when viewed through the Design Assistant 2013 inventor viewer.
View 0 Replies
View Related
Sep 5, 2012
Is it possible to split a 3d line with planes.
I am not able to find a Split method on Sketchline3d.
{Code}
Sub Split_Lines()
If ThisApplication.Documents.Count = 0 Then Exit Sub
If ThisApplication.ActiveDocument.DocumentType <> kPartDocumentObject Then Exit Sub
' Check to make sure a sketch is active.
If Not TypeOf ThisApplication.ActiveEditObject Is Sketch3D Then
MsgBox "A sketch must be active."
Exit Sub
End If
[code]...
Config :: Intel (R) Xeon (R) CPU E31245 @ 3.30 GHz, 16.0 GB, 64bit win7
Inventor 2013 and Vault Basic 2013
View 2 Replies
View Related
Jan 3, 2013
How to create a measurement between two planes using ilogic rules?
I have created the planes on the asssmbly parts but dont know how to directly pick them.
The measurement is going to be used as reference dimension.
View 1 Replies
View Related
Sep 26, 2011
see attached image. The Origin Work Planes of my assembly, and some of the origin work planes in sub-assemblies have lost their names. No longer can I see XY Plane / XZ Plane / YZ Plane - all I see is a little red dot when I hover over where the name used to be. ??
View 2 Replies
View Related
May 27, 2012
In previous versions, as clunky as it was, I used to put a work plane in the centre of a frame generator part using "G_L/2"
This does not seem to work anymore in 2013.
Inventor Professional 2014.
Windows 7 64 bit.
View 1 Replies
View Related
Jan 11, 2013
I need to downscale whole assembly if its possible. If not, its no problem for me to downscale every single part separately (apx. 30pcs) and then put it together again but I need to downscale it with all its modeling history - sketches, planes and other geometry. I can't select them when using DERIVE function.
View 9 Replies
View Related
Dec 21, 2013
They are all gone in my parts and assemblies. Only are they visible in the browser when I open a particular part or assembly of the parent. Need them for constraints .
View 9 Replies
View Related
Nov 8, 2011
I'm assembling parts and one of the parts is in my Inventor Library. When I try to make a plane visible it won't let me. I can constrain to the plane , I just can't make it visible.
Inventor 2011
Autodesk Inventor 2011
AutoCAD Mechanical 2011
View 4 Replies
View Related
Apr 8, 2013
We are just in the process of upgrading to Inventor 2013. While migrating our iParts, the origin work planes from the part part suddenly appear in some of the children. In the browser they show up under the iPart parent entry and will have names such as "YZ Plane_1". The visibility of all of the origin work features in the parent are turned off. In the children I can right click on these work planes but there is no option to turn off their visibility. And of course I can't even turn off general categories of object visibility in the children because that function is greyed out.
Is this behavior normal/new in IV 2013? Is there anyway I can turn off these origin planes in the iPart children?
View 1 Replies
View Related
Sep 21, 2012
Basically, I have two workplanes which are parallel to each other and offset by a certain distance. As illustrated in the picture below, I'd like to constrain points from each plane to have the same vertical alignment as those from the other plane (horizontal too, I suppose, but the horizontal dimension will be the same anyways).
View 1 Replies
View Related
Dec 3, 2011
I am creating a part that consists of a series of intermediate Lofts. The various Loft termination profiles are sketched on a series of stacked planes, most of which are parallel to one another. I have a Work Axis (oriented at an angle off of true vertical) that penetrates all of these sketch planes, essentially forming a "central axis" for my part. Most, but not all, of my sketch planes are normal (perpendicular) to that axis.
I want to use my "central axis" as a reference point in each of my sketches, i.e., the point where the axis intersects the sketch plane. I am having a minor difficulty.
When I project my central axis into a sketch whose plane is normal (perpendicular) to the axis, Inventor displays a reference point where the axis penetrates the plane and I can dimension my sketch geometry relative to that point. Conversely, no such point is displayed when I project the axis into a sketch plane that is NOT normal to the axis.
Is this correct behavior? To have a dimension able point on my "non-normal" sketch planes, must I create explicit Work Points to mark the intersection between my Axis and such planes, and then project those points into the related sketches?
View 2 Replies
View Related
Mar 26, 2012
I am trying to put an angular dimension from a hole to a slot positioned planes 90degrees to each other. How can I achieve this? Typically, it depends on how it is put into the ipt file but I didn't know how else to put the slot in therefore only a point was put in at that angle.
View 2 Replies
View Related
Mar 30, 2012
Ok I am struggling with this again. Some how when my assembly was made I had several work planes visable on several subassemblies. No big deal, I will just go to the subassemblies, turn them off and save them and all will be fixed right? Wrong, the assembly still opens with the work planes showing. So I expand the subassemblies and turn the visability off in the top level assembly. Now when I attempt to save the assembly I am told that the master view is locked and I need to create a new view. But I don't ever want all the work planes on and I don't want to create a new view because that leads to not being able to save a linked assembly or drawing if the wrong thing is open somewhere.
How do I unlock the master view to be able to save it with the planes turned off?
View 9 Replies
View Related
