How I could go about creating a standard locknut thread, with the shaft generator (easy so far) BUT create a proper single rounded end key way? It does the end of the locknut groove with the rad that exits the shaft, but in complete truth (and 15+ years of experience.) I have never seen this done in the real world.
View 1 RepliesI'm using Inventor Professional 2014
I created several Parts with the Shaft Generator, and from one moment to another it always says that it can't update the part file with the new shaft when I press Ok.
Here is the original error, I'm german, so of cause its in german, but i discribed above what it says:
Komponente C:UsersManuelGoogle DriveProjekteEigene ÜbungenTest2Konstruktions-AssistentWelle1.ipt konnte nicht aktualisiert werden. Welle konnte nicht erstellt werden.
I have written some VB code which updates parameters in a model. I would like the code to update the shaft parameters. The shaft is created using the shaft generator. I can use a parameters to set the lengths, diameters and fillets. But when the parameter updates the length stays the same. If I open the shaft assembly, click 'edit using design accelerator' and then click 'ok' in the window the shaft updates. Is there anyway to do this automatically?, maybe through iLogic or API?
View 1 Replies View RelatedQuestions below pertain to using Autodesk Inventor 2013:
What factor of safety value the Shaft Generator program uses when you run the calculations?
Does the factor of safety value change when you are not using the inventor user material option?
Lastly, when exactly do you know when to use the density option in the calculation properties or not?
My colleague installed IV2013. He has excel 2010 installed in his PC also. However he cannot create thread hole (thread option is grey out).
View 4 Replies View RelatedI created a frame using 150 x 75 BS4 channel section in 2011/12 (can't remember which) however it was created before the BOM length fix (all lengths stated are not necessarily the lengths of the beams). In order to fix this I need to redraw the frame, which is fair enough, however I am unable to find the BSI standard channel section. In fact, BSI has seemed to vanish from my library completely, I can not even place a component from the BSI library.
I have had a look around the C:/Programdata/autodesk/inventor2011(or 12 or 13)/contenetcentre/libraries and have found parker, gost, DIN etc but no BSI. I have not used the frame generator/place component in 2013 yet so no idea if this was from install or not.
what I would like to know is the 'simple' way to create a keyway on a shaft in the middle that does not connect to the ends. End connecting keys are pretty basic to draw and extrude thru (maybe still a better way?)
File attached for viewing .
I am trying to create a stress analysis on a shaft with two blower turbines attached. What feature in Inventor 2012 is the best way to represent centrifical force on the shaft due to the weight of the blowers and the inputs of rpm and torque.
View 3 Replies View RelatedI'd like to use an "NPT" Hole Dialog thread but it doesn't show up in the Thread type list.But it does show up in the Thread Dialog/Specifications Tab/ Thread type list so it's available.
I definitely have "NPT" in my Thread.xls & I have my Options/Files set to point to the correct Design Data folder.
Inventor Suite 2013 Ultimate
Autodesk Inventor 2013.
Could not find file C:Program FilesAutodeskInventor 2013Design DataXLS13XLSen-USThread.xls containing thread data.
I can drill a hole as needed, but can't thread a hole at all. Not with the Tapped Hole function when drilling the hole, or after drilling the hole then using the Thread Tool. Inventor will just not let me create threads this way outside of cutting a coil.
View 9 Replies View RelatedI am trying to add a thread class to the thread.xls. (that part is ok)
The thread is M26x2.0
I can't seem to find any information for me to simply plug in the values into the .xls, so I am thinking that I have to crunch some numbers. which is fine. I just want to make sure that this image below is the correct the reference for this task.
using the pitch, I should be able to calculate all my min and max values, but the xls has class column and a tap drill column, how would I determine these values??
Inventor Professional 2014-Update 2 - AutoCAD Electrical 2014
Win7-x64 | ASUS P8Z77-V | i7 3770 -3.4 GHz | 32GB RAM |
240GB SSD | nVidia GTX 670 4GB - 320.49
I have created a shaft and splined one end of it successfully. The shaft is the same diameter at both ends and I need to spline the other end as well but when I try, I get the following error messages, Cannot create iFeature. Not possible to create shaft groove. Splining the first end went without a hitch but Inventor absolutely refuses to spline the opposite end of the shaft. The shaft diameter is correct for the spline I have chosen (same as the major diameter)
View 1 Replies View RelatedHow can I put a 'center' into a shaft end in inventor? I have been doing this using the point/hole command and altering the csink details until I get something close to what I want but obviously not ideal.
Inventor 2014 PDS
I am using the design accelerator to create a shaft with multiple features. Works well. This shaft is 90"+ in length and although I realize we create in full scale, having it display into my drawing in full scale is unnecessary because one diameter is nearly 60" long. As such I would like to shorten it by using a shaft end, but cannot figure how to do it.
Just to be clear, by shaft end (term used in Mechanical) I refer to the squiggly lines that basically fudge the OAL of a component.
I am trying to create a simulation in which a shaft rotates and the a spur gear attached to the other end rotates with it. When I apply torque to shaft, the shaft does rotate but the gear does not. I believe I have done something wrong with the constraints.
View 1 Replies View Relatedi am trying to design a shaft with a cut out that would cut along the shaft a a set angle and wrap around the shaft.
I am going to have a bearing ride along the cut out and cover this to a linear motion but can't seem to grasp how you do this in inventor 2013.
Have attached a simple assembly..i have constrained the parts but how do i get the shaft/Fan to spin inside the case?
View 6 Replies View RelatedI want make Screw Shaft from sheet metal and make Flat pattern.
[URL]
Trying to dimension a shaft in isometric view with various diameters. I am unable to find or select the centerpoints at the ends of the shaft. This causes dimensions to be crooked. How can i get the centerpoints to display so that they may be selected?
View 9 Replies View RelatedI have a problem were when , i take a design accelator shaft to .idw and section it the the hatch lines do not appear as they would if it was a shft drawn from scratch.
View 3 Replies View Relatedis it possible to produce something like in the attached image using the design accelerator? Instead of making a cylinder and sketching the spline patterns and extruding? To me there must be a way besides sketching and use the library's of standard splines patterns and sizes.
Inventor Professional 2014-Update 2 - AutoCAD Electrical 2014
Win7-x64 | ASUS P8Z77-V | i7 3770 -3.4 GHz | 32GB RAM |
240GB SSD | nVidia GTX 670 4GB - 320.49
I create a engine assembly and used "Drive Constrain" to rotate the crank shaft. The animation shows the crank shaft turns continuously in one direction. However, when I animate the constrain in Inventor Studio, the crank shaft turned in two different directions (see the vide file attached).
May I know why the crank shaft turns different direction?
You can organize a multi-threaded work with data through Inventor API? For example, there is a assembly and I need the first part of assembling a list of items to consider in a data set, the second part of the list - in the second data set, the third - the third and so on up to N, where N - depends on how many threads can run in the system . Whether these flows are processed and to receive data in parallel? Or go to the consistent implementation of this algorithm will first be processed by the first part, and only after it will start the second ...?
Autodesk
I am having a terrible time getting the thread modeler to work correctly for an M16x 1.5 thread. I have tried multiple approaches to get the correct thread dimensions output.These are the steps I take:
1) Create hole (I've used both major and minor thread diameters,16mm and 14.376mm)
2) Apply Inventor threads (M16 x 1.5)
3) Select threads from tree using the Add-in thread modeler "Controller"
4) Analyze dimensions finding both cases yield the wrong dimensions.
This add-in would be very useful and a great time saver if it would work correctly.
How to add a Thread to both the Nut & Bolt....i always use the Thread Tool but i would like to also know how to add an actual thread.
View 2 Replies View RelatedI need to add thread to a hole but cannot do this under the edit command. How to do this ?
View 7 Replies View RelatedI need to make a thread of 8 D.P.I on a diameter of 104.8 mm.It's not a standard thread size.Where is the excel file with the ANSI threads?
View 9 Replies View RelatedI have recently installed Inventor 2013 Professional Ultimate and am having some issues. I can not seem to get the Thread function to work. When I go to apply a thread I get the follow error....
When I go to search the directory, I find that the Thread xls document is infact there, but it is not located where the program thinks it should be (XLS Folder --> en-US Folder)
I also made sure that the Design Data location was correct within the Application Options...
A reboot of the computer did not work.
Is there a way to create a new sdf files with certain colour, transpacency etc (standard that i create) and not random colours?
View 2 Replies View RelatedIn my project file, under design data folder options, I have it set to c:designsStandardsStyles. This is where I have my thread.xls located.
When I try to place a threaded feature, Inventor gives me a warning that it cant find the Thread.xls file.
It is looking for this file in c:DesignsStandardsStylesXLSen-USThread.xls. Where is it getting this path from?