I need to know how to dimension to a theoretical sharp on bent flanges. In an .idw it wont snap to the sharp and when a schetch is created for one it does not dimension between them only one or the other.
View 2 Replies
Is there a way to change the way the dimensions text shows up at arbitrary angles and make them all uniform?
View 4 Replies View RelatedIt must surely be in there somewhere but I cant find a way to dimension to a line's midpoint in a sketch.
View 3 Replies View RelatedThis is probably a simple one, but when I dimension from an edge to the tangent of a radius or circle. It always snaps to the center. How do I get the dimension to snap to the tangent point?
View 9 Replies View RelatedIs there a way that i can Double Dimensioning? as to have one dimension in decimal and one in fraction all in the same dimension line?
Im using 2011 RS
I needed to create new dimensioning styles - that I can do. However, there doesn't seem to be a way to apply them to a current drawing. In the Annotation section under Format there are no "styles" listed - not even the default.
So, how is one able to populate the list so one may choose a specific style or another? Or, is there somewhere else I should be looking?
BTW...AutoCAD Inventor 2012
How do I dimension, and assign editable parameters between different extrusions on one part, to change the height, width, etc?
View 9 Replies View RelatedUsing the Hole command, I want to locate / reference off datums, this is something I can do in Pro-E. It's not a choice, that I can find.
View 8 Replies View RelatedI trying to figure out a way of dimensioning a curve for fabrication in inventor. The way i have done this before was to provide a chart of X and Y dimensions of points along the curve. See the attached drawing.
View 6 Replies View RelatedI have run across a situation that I have not been able to find having been previously asked. I have attached the file of what I am working on.
I have 2 dimensions to the implied intersection, but how do I put the dimension when there are 2 implied intersections? Such as along the bottom of the part.
I have a couple of quick questions about dimensioning holes in drawings .
First, if I have a hole in a rod or shaft so the surface isn't a full circle I get the dimension as a radius. Can I change it to a diameter?
Second, in a model, how do I dimension or measure to the edge of a round rather than to it's center? In SW I could hold the shift key while selecting, is there a similar method here?
I design molds for the rubber industry and I was using Acad 2000; I am just now starting to use inventor. I need to used the ordinate dimensioning although I need the dimension to be given as a diameter and not as a radius. Is there anyway to scale the ordinate dimension automatically as 2:1? This way when I give the prints to the tool room they don't have to manually double every diametrical dimension. The prints that I draw only show half of the mold, there for needing a 2:1 dimension scale.
View 9 Replies View RelatedIs there an easier way to dimension to a virual sharp or place the ordinate dimension origin on a virtual sharp than by trying to drag the point along each line until you get the dotted lines to intersect?
View 6 Replies View RelatedIn the course of working up a tooling proposal, I attempted to replicate a 3D part from a customer print. While doing so, I noticed that 3D Sketch will not, under any circumstances that I can find, allow an angular dimension between a line and a plane. The customer print has two pipes projecting at odd angles from a base flange, one of which has an elbow. The print lists datum dimensions for the open pipe ends and the elbow, and gives vertical and horizontal angular dimensions to define the directions in which the pipes emerge from the flange. I have defined these three datum points in 3D space without any trouble, but Inventor 2013 will not allow me to define an angle between these sketchlines and the XZ and YZ origin planes, or between these sketchlines and the faces of the flange base I've constructed.
I am currently waiting on a proper 3D CAD model from the customer, and I'm considering longhand trigonometric calculations to place these lines properly, but I find it very hard to believe that Inventor is incapable of constraining a line to lie along what is effectively the surface of a cone.
Using:
Inventor 2013
AutoCAD 2013
I have created some "programs" to automate drawing creation of some of our most common products. The problem I hav eis with my assembly drawing. When parts are suppressed and unsuppressed, they don't seem to behave the same way that features do. When you dimension a part feature in an idw and suppress that feature, if a week later you unsuppress that feature the dimenensions come back. Parts don't seem to follow this behaviour. If you dimension a part, suppress it, open and save the drawing, then later unsuppress it and open the drawing back up the dimesnions do not come back. Is there anyway for me to get these dimensions to "stick"?
View 9 Replies View RelatedHow do I make inventor show the " symbol while dimensioning? It will show when using architectural units but not in decimal. R2012
View 4 Replies View RelatedI am trying to use sketch points in drawing for dimensioning. Below is portion of my code. The code fails when AddLinear is called. Is it even possible to use drawing sketch points for dimensioning?
invSheet = invDrawingDoc.ActiveSheet
Dim oTransGeom As Inventor.TransientGeometry= invApp.TransientGeometry
Dim pt1 AsPoint= oTransGeom.CreatePoint(0, 0, flangeOD / 2)
[Code]....
I am needing to put a horizontal dimension from the implied intersections of a "Z" shape. In the attached screen shot, I have a question mark at the dimension I'm needing.
I have tried the RMB / Intersection in different ways, but none giving me the dimension. How do I go about getting this dimension?
I am currently attempting to dimension to a spline in an orthographic drawing and running into some issues. I can't seem to find a way to properly dimension rather than making microscopic holes in the piece and that way giving the .idw something to grab on to for dimensioning.
View 2 Replies View RelatedHow can I have both Inch & Metric dimensions on a drawing? Preferably, inch above metric below.
View 1 Replies View RelatedIs it possible to automate dimensioning of drawing views?
Here's the situation: I have an Inventor assembly that's controlled entirely by iLogic. My users, who have zero Inventor training/experience (or with any 3D CAD software for that matter), pull up the assembly. They enter product related parameters from paper work orders into an iLogic form and hit a "Go Button". The assembly updates based on the parameters, suppressing and unsuppressing parts, features, patterns, and mates. This works great. They then hit a "Run Job" button. This takes them to an .idw where they fill out another form with order specific information and hit another "Go Button". This then cycles through every detail sheet and the parts list, deleting sheets deeemed unneccessary for the product, generating part numbers, exporting dxf's, generating an excel BOM, etc.
This works great as well. The problem is with the dimensions. They blow all apart when the model changes. I know I can run some API code to delete dangling dimensions, but is there away to programmatically create dimensions so I don't have to rely on my users remembering what needs them? I've played around with using model dimensions, but I find that they stay and remain attached even when their corresponding feature gets suppressed.
IV 2012
I'm wondering is it possible to orientate the dimension text alligned to paper(2.jpg) but not the UCS of Isometric drawing(1.jpg).
Sometime I need to allocate my drawing with dimensioning in isometric view because its more easy to read.
I'm placing my drawing in *.idw.
I'm having problems getting Inventor to dimension using the current view option on an assembly. I ungrounded the assembly and constrained it to the angled work planes that I needed so I have to use the current view option, but when I try to dimension to the intersection of the angles, it won't give me a dimension.I'm using Inventor 2011.
View 1 Replies View RelatedI find the 3D side of the software is great for modeling. But when it comes to the 2D drawing side of it, especially dimensioning and the adding of text label is very poor, when compared again other CAD packages including AutoCad Mechanical and LT.
Why is it not on par with AutoDesk other 2D packages!
(Using Inventor 2013)
I'm using Inventor 2010.
I've been told to create new dimensioning styles for the company to use as standards when making a drawing. One thing mentioned in particular was the inclusion of 0 inches in architectural drawings.
For example: say a part is 14 feet, 1/2 inches long. Inventor shows this: 14' - 1/2" , but they want this: 14' - 0 1/2" . They've had a problem before with the 1/2 being printed strangely, and the machinist thought it said 1 1/2.
They say that including the 0 is standard, and I need to make it happen.?
I am creating a part that consists of a series of intermediate Lofts. The various Loft termination profiles are sketched on a series of stacked planes, most of which are parallel to one another. I have a Work Axis (oriented at an angle off of true vertical) that penetrates all of these sketch planes, essentially forming a "central axis" for my part. Most, but not all, of my sketch planes are normal (perpendicular) to that axis.
I want to use my "central axis" as a reference point in each of my sketches, i.e., the point where the axis intersects the sketch plane. I am having a minor difficulty.
When I project my central axis into a sketch whose plane is normal (perpendicular) to the axis, Inventor displays a reference point where the axis penetrates the plane and I can dimension my sketch geometry relative to that point. Conversely, no such point is displayed when I project the axis into a sketch plane that is NOT normal to the axis.
Is this correct behavior? To have a dimension able point on my "non-normal" sketch planes, must I create explicit Work Points to mark the intersection between my Axis and such planes, and then project those points into the related sketches?
Is autocad 2012 capable of dimensioning a solid object in model space horizontally vertically and diagonally say across the opposite corners of a cube, or along the hip of a roof? What am I missing here, I am using the full version of autocad for exactly this feature but am still unable.
View 4 Replies View RelatedWhich category in the Dimension drop down menu do I use to obtain the linear dimension for the length of an arc, a 1/2 circle, for example.
View 4 Replies View RelatedWhen I am typing out text and get to a fraction is allows me to stack it diagonally so the 1/4" looks nicer. When i dimension, however, it does not seem to stack the fractions the same way. I took a look at the Format - Dimension setting and did not see the option in there to change it. I would like to have the fractions stack diagonally like they do regular text.
View 1 Replies View RelatedIs there a way to have AutoCAD use the "right angle symbol" instead of showing 90 degrees when it measures right angles?
View 8 Replies View RelatedWhen I am doing the details for a drawing I need to show the point at which a dimension on the elevations precisely starts but instead of the actual dimension I need a description such as "Frame Height", "Rough Opening", "Offset From Columnline", etc. I have always entered "T" after I set my two points for a dimension to replace the dimension with text. On my detail sheets there are a lot more of these than actual dimensions.
View 8 Replies View Related
