AutoCAD Inventor :: Create New Dimensioning Styles For Company To Use As Standards
Jan 25, 2012
I'm using Inventor 2010.
I've been told to create new dimensioning styles for the company to use as standards when making a drawing. One thing mentioned in particular was the inclusion of 0 inches in architectural drawings.
For example: say a part is 14 feet, 1/2 inches long. Inventor shows this: 14' - 1/2" , but they want this: 14' - 0 1/2" . They've had a problem before with the 1/2 being printed strangely, and the machinist thought it said 1 1/2.
They say that including the 0 is standard, and I need to make it happen.?
We have three divisions in my company. Each division uses a different set of drawing templates.
With all of that said, in my division we are trying to setup a certain said standard that was copied from the out of the box standard ANSI one as a starting point. We were hoping to have this standard reside only in our drawing templates, but the way the styles is handling it, it would appear that this standard has to be updated/added to the global styles library.
Is this a true statement that this has to be a global styles update or is there a way to have a said standard be the default setting within just certain drawing templates without being seen or affecting other drawing templates?
I needed to create new dimensioning styles - that I can do. However, there doesn't seem to be a way to apply them to a current drawing. In the Annotation section under Format there are no "styles" listed - not even the default.
So, how is one able to populate the list so one may choose a specific style or another? Or, is there somewhere else I should be looking?
How to create extra plug-ins for the standards checker. Currently AutoCAD only ships with 4 plug-ins:
Layers Dimstyles Textstyles and linetypes
I'd like to add a plugin at our office to also check table styles, multileader styles, and possibly other things such as making sure our title blocks are at the proper location, or that nothing is drawn on the layer 0 (unless in a block).
I am new to the Adobe Suite of products. I nee do create letterhead and a brochure for my company. I also need to be learning how to Blog as that is going to also be assigned to me. Is there anyplace I can find some direction on how to do this?
I'm working on homogonizing all of our various templates, making all the new features from newer templates available in the older templates but I'm getting high centered on a step.
I've exported all of the different drawing standards and imported them all into each template which makes all of the upgraded dim styles available in all of the templates. The issue arrises when I save and close then reopen the template the imported standards are missing. It appears that under Manage, Styles Editor, if the standard is not in use it is not saved with the template. If this is the case how do I put them all "in use"? Even if I activate one of the imported standards, save, close, reopen, then activate a different standard and repeat, the imported standard is deleted.
I am trying to transfer my company logo in DWG format to Inventor to put on my custom border I am currently making. I tried copying and pasting but it doesnt work.
How do update the styles library to keep from getting the Styles Conflict error box. I have used the Standard.dwg file that loaded with Inventor 2012 but everytime I change styles and save the changes in a new template in reverts back to the library definitions.
I used to be able to select 'NO' in the LIbrary option of the Projects Folder but that optiion no longer exists.
We've created a new parts list style for a border.When the border tempalt file is on the c: drive...everything works hunky dory...parts list, revision tables, etc.But as soon as we copy and paste that border into the template library folder for new drgs...the parts list style is missing from the local styles?
So to make it appear on the new document...the style manager has to be set at all styles and the new parts list style has to be saved to the document?What aren't we doing to make it appear on the template?
Also note that because the drawing border template is in a template folder as part of the design projects...it is NOT editable...so it has to be edited outside the template folder.
If we as a company already have our Inventor 2011 seats installed and we now want to 'push' out the company standard application options is there a way to do this other than using a manual import?
Autodesk Inventor 2010 - How do I set default for "use standards notation" to off or unchecked in the "Edit Unit Attributes" dialog box for feature control frames? I want to do this because the Feature Control Frame style unit setting does not override it as I believe it should. This causes an extra value within the tolerance box of the feature control frame if the Standard General units differ from the style’s primary units.
I need to know how to dimension to a theoretical sharp on bent flanges. In an .idw it wont snap to the sharp and when a schetch is created for one it does not dimension between them only one or the other.
This is probably a simple one, but when I dimension from an edge to the tangent of a radius or circle. It always snaps to the center. How do I get the dimension to snap to the tangent point?
I trying to figure out a way of dimensioning a curve for fabrication in inventor. The way i have done this before was to provide a chart of X and Y dimensions of points along the curve. See the attached drawing.
I have run across a situation that I have not been able to find having been previously asked. I have attached the file of what I am working on.
I have 2 dimensions to the implied intersection, but how do I put the dimension when there are 2 implied intersections? Such as along the bottom of the part.
I have a couple of quick questions about dimensioning holes in drawings .
First, if I have a hole in a rod or shaft so the surface isn't a full circle I get the dimension as a radius. Can I change it to a diameter?
Second, in a model, how do I dimension or measure to the edge of a round rather than to it's center? In SW I could hold the shift key while selecting, is there a similar method here?
I design molds for the rubber industry and I was using Acad 2000; I am just now starting to use inventor. I need to used the ordinate dimensioning although I need the dimension to be given as a diameter and not as a radius. Is there anyway to scale the ordinate dimension automatically as 2:1? This way when I give the prints to the tool room they don't have to manually double every diametrical dimension. The prints that I draw only show half of the mold, there for needing a 2:1 dimension scale.
Is there an easier way to dimension to a virual sharp or place the ordinate dimension origin on a virtual sharp than by trying to drag the point along each line until you get the dotted lines to intersect?
In the course of working up a tooling proposal, I attempted to replicate a 3D part from a customer print. While doing so, I noticed that 3D Sketch will not, under any circumstances that I can find, allow an angular dimension between a line and a plane. The customer print has two pipes projecting at odd angles from a base flange, one of which has an elbow. The print lists datum dimensions for the open pipe ends and the elbow, and gives vertical and horizontal angular dimensions to define the directions in which the pipes emerge from the flange. I have defined these three datum points in 3D space without any trouble, but Inventor 2013 will not allow me to define an angle between these sketchlines and the XZ and YZ origin planes, or between these sketchlines and the faces of the flange base I've constructed.
I am currently waiting on a proper 3D CAD model from the customer, and I'm considering longhand trigonometric calculations to place these lines properly, but I find it very hard to believe that Inventor is incapable of constraining a line to lie along what is effectively the surface of a cone.
I have created some "programs" to automate drawing creation of some of our most common products. The problem I hav eis with my assembly drawing. When parts are suppressed and unsuppressed, they don't seem to behave the same way that features do. When you dimension a part feature in an idw and suppress that feature, if a week later you unsuppress that feature the dimenensions come back. Parts don't seem to follow this behaviour. If you dimension a part, suppress it, open and save the drawing, then later unsuppress it and open the drawing back up the dimesnions do not come back. Is there anyway for me to get these dimensions to "stick"?
I am trying to use sketch points in drawing for dimensioning. Below is portion of my code. The code fails when AddLinear is called. Is it even possible to use drawing sketch points for dimensioning?
invSheet = invDrawingDoc.ActiveSheet Dim oTransGeom As Inventor.TransientGeometry= invApp.TransientGeometry Dim pt1 AsPoint= oTransGeom.CreatePoint(0, 0, flangeOD / 2)
I am needing to put a horizontal dimension from the implied intersections of a "Z" shape. In the attached screen shot, I have a question mark at the dimension I'm needing.
I have tried the RMB / Intersection in different ways, but none giving me the dimension. How do I go about getting this dimension?
