There are times with a breakout that it is desirable to have the sketch used to create the breakout visible to make it clearer on what's going on. When I right-click on the sketch in the browser there is no option for visibility. How do I make this sketch visible?
View 2 Replies
This subject have been around since version 2008.
1- I want to be able to insert an ipart ( only sketch) into an assembly and run frame generator.
2- If I have to change the component in the assembly I want to be able to click the ipart table with the right button of the mouse and choose "change component".
picture in attachment
2008/2009 Bug
[URL]
What is the difference between:
1) create a sketch
2) create an extrusion
3) make the sketch VISIBLE
4) create another extrusion
and:
1) create a sketch
2) create an extrusion
3) make the sketch SHARED
4) create another extrusion
I'm making a part and am adding features to it and using my existing sketch dimensions as my guide. The problem is that when there are sketch dimensions on the face of the part, they are difficult to read. I'm forever dragging these dims to the side in order to read them, it's just a bit annoying. I was wonering if there was a setting that made them show up as well as they do when the aren't sitting on the face of my parts. I've attached a .jpg of what I'm talking about. notice the dimension on the left side and the bottom.
View 2 Replies View RelatedIf you have a section view, shafts are typically turned off for segtioning, however there is sometimes detail such as keyways or oil holes that are required to be shown which is where a breakout, view is req'd, however it appears the only way to do this is by creating a detail view first, leading to the possibility of a lot of clutter on the drawing from detail views, as when a breakout view is created on the section view, the shaft will not participate in the breakout.
View 3 Replies View RelatedSince Bolts nuts and key shafts are not sectioned according to standards I can´t find a way to section a shaft inside a section view without cutting through these components. I have posted in attachment an example of the problem and a picture of what it should be like.
View 2 Replies View RelatedMy coworker gets this error:
He makes a detail. In the enlarged view he makes a sketch. He then makes a break out. Within the enlarged view, in the gap which the break out opened up for clarity of the view, are two components that he wishes to make its hidden lines visible. Doing this locks up his machine and makes a single component turn red.
Dell Precision T3600 - Windows 7 SP1, 64x
16GB RAM, NVIDIA Quadro 2000 (driver 9.18.13.3165)
Inventor 2013 SP2 Update 2
AutoCAD 2013 SP2
Vault Collaboration 2013
3DConnexion SpaceNavigator
I am trying to do a detail view on an isometric and i would like a long sausage shape angled with the isometric. the detail views are round or rectangular horizontal, i would even be happy with a rectangle on the piss in line with the isometric.
i tried putting on a sketch of my sausage shape and performing a breakout view but it will only take away the components within the sausage, i want to flip this. I then tried putting a big rectangle on the same sketch in the hope that it would leave the sausage as an island, (much like a hatch) .
In the drawing view below, I want to section the green assembly only within the red section. I've tried this with a breakout and it doesn't work. There doesn't seem to be a way to exclude the green from the section and yet include it in the breakout.
Infrastructure DSP '14 / Product DSP '14 / Vault Professional 2014
Dell Precision T1650
Windows 7 Professional SP1 64-bit
Intel E3-1270 V2 3.5GHz / 32G RAM
Nvidia Quadro 2000, Driver 331.82
Space Navigator, Driver Version 6.17.7
I've created a shared sketch and have used it with various features. Sometime those features are suppressed. The model works fine but the shared sketch generates a sketch doctor error because the feature that created it has been suppressed. Is there anyway to make the sketch suppressed so it doesn't trigger a sketch doctor error? Inventor 2013
View 2 Replies View RelatedHow do I duplicate the 2D line work from a part level sketch into a drawing level (overlay) sketch?
I started a simple 2D piping system diagram sketch by opening a new part file and using a sketch to stick draw the system schematic including some annotations. Then I opened a new drawing file and made a base view of the part file to bring a view of the original sketch into the drawing.
I realize now that it would have been much easier to have created the schematic directly in a 2D sketch at the drawing level, which would have made editing the annotations much easier at the drawing level, and there is really no need for the part file to exist. I have no intention of creating a 3D model or "real" part in the .ipt file, was just using it as a jumping off point to sketch.
I was thinking that I could correct my error in judgment by just copying the sketch and pasting it into a new sketch on the drawing, but it doesn't want to work that way. I have tried copying both the whole sketch at the browser level, and the entire sketch contents (all of the lines and annotations) from the opened part sketch, but when I attempt to paste either of those into the drawing, paste does not seem to be an option. I'd rather not have to draw the whole thing again, as in typical fashion, my once simple sketch has grown in proportion and complexity from its simple beginning.
I was trying to query some sketch points data from a profile Path using code as below. However the program stopped without telling the reason.
Code below:
i = 0;
foreach (ProfileEntity oSourceProfileEntity in oProfilePath) { switch (oProfilePath[i].SketchEntity.Type) { case ObjectTypeEnum.kSketchArcObject: { SketchArc srcSkArc = default(SketchArc); srcSkArc = (SketchArc) oSourceProfileEntity.SketchEntity; // error points[i] = srcSkArc.StartSketchPoint.Geometry; break; } default: { SketchLine srcSkLine = default(SketchLine); srcSkLine =(SketchLine) oProfilePath[i].SketchEntity; // error points[i] = srcSkLine.StartSketchPoint.Geometry; break; } } i++; }
First we imported an ".igs" file to inventor, which produced "wires". Then by promoting the wires it produced a 3-d sketch.
The model is in one plane and 2-D, and we are trying to use Ansys 2-D analysis, but in-order to do so it needs to be in a 2-D sketch.
The model is too large to be redrawn on a 2-D plane, how to convert it to a 2-D sketch
want to change sketch 2013 into the sketch of 2010
View 1 Replies View RelatedWhen I edit certain sketched some other sketches disappear. see attached.
This is causing modelling to slow down as I can not project lines from the sketch that has disappeared.
After I create a adaptive part from projected sketch. How to modify the sketch? Please see the part attached.
View 6 Replies View Relatedwhat is the difference between a sketch and a planar sketch?
View 2 Replies View RelatedI'm having trouble with constaints, I'd like to constrain my sketch to a point in another sketch on a different plane. Is this posible in Inventor? If so how? If Inventor works differently how would you get a points in one sketch to be linked to points another?
View 2 Replies View RelatedIm trying to make an avatar.
I want it to look like something is ripping through the screen.
There are some lines that are not visible in my .IDW. I have had this before and am wondering why this is happening. Basically this is a vinyl gasket which is shown in my .iam file. In my .idw it is not showing although I have not turned off the visiblility of the part.
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
Two computers with Inventor Pro 2011 on them, same set up in Apllication Options/Content Center and Apllication Options/File. On one Inventor sees Content Center on the other does not. What could be the problem?
View 2 Replies View RelatedI'm working on a small Assy (25 parts). When I open one of the parts from this Assy and work on it then go back to the Assy many parts are not visible. The update button is usually off so I can't use it.
This started only about 2-3 weeks ago - in every assy. I changed the nvidia driver but didn't work.
Inventor pro 2012
Win 7 Pro. sp1 64 bit
Intel Core I7-2600 CPU
Ram - 8GB
Quadro 2000 D
Nvidia 275.89 (tested nvidia 296.70 with no luck)
I have imported an .igs and would like to use it on my assembly.
Step that I created.
1. DL an igs files, then open it in Inventor 2012 Product Suite.
2. Save as .ipt,
3. Create a new .ipt and then DERIVED the save .ipt, change scale to 25.4
4. Save the part
5. Open .idw and place the part you just save.
Result: Notice that nothing is visible. WHY?
Attached is a test drawing
1. Why does my part not show up behind a surface?
2. What is the minimum dimension to make my part appear?
On the drawing I was working on, the part completly behind a surface was showing up until I rotated the view, then it dissapeared, this behaviour is not present in the test idw, the part doesnt appear at all behind the surface.
I can't see any of the inventor toolbars anymore.
if i would still have the Quick Acces Toolbar this wouldn't be a problem but that one is also gone.
in my assembly part visibility is controlled by a Ilogic rule which selects an Iassembly. This assembly is a parametric model controlled by excel. The visible parts have to be exported to dxf.
Everything is working (iterating through parts, export sheet metal to dxf), but how can I check whether a part is visible within the assembly?
I have unfolded a 3D model into a flat plate, however the bend lines/extents do not appear in ISO.dwg
I doubled clicked into the view to access 'Display Options'. However, I cannot tick the box to display bend extents as this option is shaded out (refer to attached screen dump).
For some reason I have not been able to generate a pdf file with visible lines fro the attached file.
View 9 Replies View RelatedWe resently upgraded to Inventor 2013 and since then we have been having an issue of dimension and leader lines being hidden under a text box or some other drawing entity.
This is very confusing since the text box does not have a white out associated with it, nore is there a way to put the test box to the back and dimension lines to the front...
It seems like our puppet masters that program this amassing tool where up to something and didn't quite get there.
IT sure would be nice (or an absolute requirement) that this gets fixed so I don't have to learn new hoops to jump through to get a quality drawing out of Inventor.
I know how to get the "work features" to show up in the assembly however, I would like to to be able to utilize the UCS if possible. When I try to use the iPart Author to select the Work Features the UCS doesn't show up.
View 3 Replies View RelatedI'm using inventor studio for the first time(Inventor 2014 / Windows 7). I'm having some trouble with work surfaces showing up in my rendering. The surfaces are set with the visibility turned off. When I'm in my normal assembly window, they're invisible. They're even invisible while im in studio, setting up lights & such. They only show up on my renders. If i go into each part and suppress them they render ok. Problem is I have sketch geometry and constraints that crash when they're suppressed, so I really need them as active, but invisible.
View 3 Replies View Related
