AutoCAD Inventor :: 2014 Placing Nuts And Bolts
May 29, 2013
We just upgraded from Inventor 2012 to 2014. When placing nuts and bolts in an assembly in 2012, you were able to select a hole and it would automatically size the bolt to the correct diameter. You could also select if you wanted it to fill in all holes of that size, on a face, with the bolt or you could just place one component.
I do not remember if it is just a setting that allows it that i can't find or if it is a bug and the drop function is not working properly, is there anything special that i need to do?
View 2 Replies
ADVERTISEMENT
Dec 3, 2013
I have modeled up a nut and bolt.
1. Have i matched the thread size correctly.I made the bolt thread the same size as the nut thread size
2. I see these in the Content centre but if i want to make my own nuts & bolts with various sizes.I can then just select the required sizes
3. How do you name your nuts & bolts.
View 4 Replies
View Related
Jul 30, 2012
In the image below, I need the C channel that the bolts are going through to section but not the nuts and bolts. In application options I have "Section standard parts" set to "Obey browser settings". In the part "document settings" I have the "participate in assembly and drawing sections" option checked, but the C channel will not section and when I right click on it in the drawing browser, the "Section participation" options are greyed out.
View 3 Replies
View Related
Jan 10, 2013
How to make the nut in this assembly turn with the thread, all I can figure out how to do is put it all the way in then turn it 360 degrees.
i5 3570k@4.4ghz gtx 670, 8gb ddr3 1600mhz
View 3 Replies
View Related
Jun 27, 2012
When i convert idw (drawing) to dwg (AutoCAD) with Save as -> Save Copy as . I have problem with nuts
Inventor Professional 2013 update 1
see picture
View 2 Replies
View Related
Feb 15, 2012
I created an assembly with screws and nuts which are not from content center. When creating a section view on Drawing, screws and nuts are also sectioned, but I don't want to.
Is it possible to see entire screws and nuts in a section view?
View 9 Replies
View Related
Jan 29, 2013
How or where can I get in ipt - files of DIN 7504-K screws?
View 1 Replies
View Related
Mar 8, 2012
I`m going to make some different size bolts,nuts and washers and instead of creating each from scratch or from content center can i use either parameters,excel spreadsheet or ilogic to save me some time.Now i have never used any of the above features so am asking for some assistance and guidance in which would be the best way to do these tasks.
I make a sample bolt with Inventor 2012 version.Would this be easy to use any of the above mentioned to simply just change sizes and update the part and features to the new size?
View 2 Replies
View Related
Aug 25, 2009
What's the best way to populate the studs and nuts on a flanged connection in tube/pipe? Can studs be added to the bolted connection content?
2010 Routed SystemsInventor Professional 2014 Build 222
Dell Precision T3500, Intel Xeon W3550 3.07 GHz, 12GB RAM, Win7 SP1
View 8 Replies
View Related
Mar 8, 2011
Bolted connection, clevis pin and bearing are all not working for me. I can go through the steps of selecting the start plane and then the circular reference and the termination point. That is all successful but the bolt doesn't appear, whether I use a clevis pin or a bearing, I get the same result.
Working with sheet metal or FrameMaker all work fine. My content center shows all the bolts, clevis pins and bearings. The content center seems to be working fine. I'm using inventor 2011.
View 9 Replies
View Related
Jun 18, 2013
Myself and my coworkers have noticed that some times bolted connections will be missing a bolt. The bolt in question will appear again if you edit the bolted connection and hit ok and let it rebuild. But then another bolt in a different bolted connection will disappear. I just went back and forth between updating two sets of bolted connections and each time I updated one a bolt in the other disappeared. It's almost like there is a limit to how many bolts the assembly will show at once. The assemblies in question don't always have large numbers of bolts and other hardware though.
I'm running Inventor 2013 SP2 running Nvidia Driver Release 276.42 [8.17.12.7642], which is the last recommended driver. I've also run newer/older drives with no difference.
View 1 Replies
View Related
Sep 6, 2010
I have noticed that when I place a group of bolts in to a group of existing holes the pattern of bolts seem to be free to rotate about the hole selected when creating the bolt pattern.
I am using Inventor studio 2011 with windows 7
View 4 Replies
View Related
May 28, 2013
I am trying to generate bolted connections using the heavy hex bolts - this family does not appear when trying to select - I only get Cap Screws and standard Hex Bolts (amont the slotted varieties) - why no heavy hex hd. structural bolts?
Product Design Suite Ultimate 2014
Vault Professional 2014
Windows 7 Pro SP1
HP-Z400: 2.67 GHz 12 Gb Ram
Nvidia Quadro FX1800 driver 276.42
View 6 Replies
View Related
Jan 26, 2012
(Inv Pro 2012, XP64, Vaulted Project and Content Center)When I'm placing hardware, the Autodrop function is really convenient. Even better when the "multiple" pickbox is active, which from what I understand is when Inventor finds similar features on the same plane that the selected autodrop component could potentially mate to.
This is a huge time-saver, since I often have lots of bolted joints that all terminate on the same plane. Sometimes however, even when the parts lie in the same "plane", the plane isn't contiguous in that a feature breaks it across. No biggie, it just means I have to do two or three "multi-autodrops".
Once I put washers at the back side of the connections (which multiple works like a charm on), all of a sudden when I go to place nuts, each washer surface is now it's own plane, and multi-drop no longer recognizes all the other parts. This can be a real pain manually placing 30 or 40 nuts at a time.
I think the "Bolted Connection" option might work, but I really don't have a need to store all those subassemblies, name them, keep them vaulted properly, etc. That would be almost as much of a headache.
Also, most of the features that I'm connecting through are created as Hole features and as "nominal" oversized bolt holes as Inventor suggests when the "clearance hole" option is used for hole creation (not randomly extruded islands), but they aren't patterned as they don't follow a prescribed circular or rectangular pattern.
Am I missing something that I can do (like something stupid simple such as holding down the "alt" key or some crazy thing like that) that will allow inventor not just to suggest CONTIGUOUS planar features, but also CO-planar features so I can place all these nuts at once?
Short of creating a custom Content center part that consists of a nut / washer assembly I can't think of anything. And creating and publishing the nut washer assemblies will eat up some time too, since I have about 50 different combinations (some SAE washers with normal hex nuts, some SAE washers with ESNA hex, some USS washers with jam nuts, some USS Type B washers with all-steel locknuts, etc...)
View 2 Replies
View Related
Apr 11, 2013
Some times we use standard parts which we could not find in content center. We creat part ourselves. But it looks like standard part in BOM or part explorer window...
I want to change type of part to PURCHASED type and icon like other purchased parts like bearings or bolts...
Is this possible?...
It can be also assembly parts like bearings. Bearings have many parts but it looks only one part in part explorer. This is very good. I want same thing too...
View 9 Replies
View Related
Jun 1, 2012
I am trying to place a tubes cylindrical surface to another tubes cylindrical surface using add constraint. How do I specify which side of the target surface to apply the constraint ?
View 4 Replies
View Related
Sep 26, 2013
Subject: Inventor placing Iparts in Assembly (Autodesk Inventor 2010)
Problem:
When placing an Ipart into a project Assembly it will make a copy of that variant and place it in the same map as the Ipart.
So when variant B of Ipart A is selected it will make a copy of variant B in the same folder where Ipart A is located.
Question:
Is it possible to make a “save as” option or another similar manner to save those copies of variant B in a project map of a project assembly?
Instead of saving all the Ipart variants to a single folder. So each time a new project is started they have all the parts in the same folder.
Reason:
I am making a local library for parts that are used for repairs. These parts have many variants and some times need to be customized for a repair.
The current system keeps polluting itself causing the users to loose their parts and accidentally delete the original parts etc.
I contacted Autodesk support and theyrecommended to post this question on this forum. They did mentioned that vba programming could achieve this. I have no knowledge of this type of programming.
View 1 Replies
View Related
Oct 24, 2011
How do I place a hole on a circular part at a specified distance from the edge. This works on other parts with straight edges, but there is no option to do so on a circle.??
View 3 Replies
View Related
Mar 7, 2012
the "place item from vault" icon is grayed out and not available for selection. how do a place a stock part located in the vault, into an assembly i am currently working on?
View 2 Replies
View Related
Jan 16, 2012
I am experiencing a crash when I try and place an ipart (any of them) into a new drawing. The open file box works but when the base view is placed in the drawing it has an unexpected problem and crashes.
Is this a documented problem , and a hotfix is forthcoming or is this just me and something local to my installation. Normally my install is very stable.
View 2 Replies
View Related
Nov 15, 2011
How to place a label on a harness.
i have created a label in library, modified and saved. WHERE IS THE BUTTON TO INSERT????
Maybe i have this mixed up. Are we talking about a virtual label or a real label (textbox describing label)?
I would like to add a 1-12" plastic covered adhesive label at each connector to identify the connector. Usually we place a text box with an identifier and a table with the label data on the drawing.
This is what i am trying to do. Is this not right? Is this the nailboard label that inventor is talking about or am i out to lunch?
Windows 7 64 bit
Inventor 2012 Professional
Dell T1600 CPU E31245 @ 3.30GHz
8 GB RAM
View 4 Replies
View Related
Oct 16, 2013
We are developing a macro for steel structures and we know about the program to insert or place a content center component in assembly through VBA programming. If there are provisions for changing the object type and changing length in that importing process it will be very useful.
View 9 Replies
View Related
Oct 31, 2012
Using bolted connection, I want to place a bolt through 3 sheets of metal. The first 2 sheets i want it to automatically place a slightly larger hole (which it does) but I want the 3rd sheet to be threaded so the bolt thread and hole thread are the same size.
View 3 Replies
View Related
Dec 5, 2011
how to place a dimension on a section line as shown below. This was drawn in SolidWorks but I am trying to convert to Inventor.
View 4 Replies
View Related
Dec 3, 2013
I am using Inventor 2012.
I created an assembly in Inventor and now I am creating a drawing for it in Inventor. I have a few views placed of the same assembly.
Is there a way to lock one view in the assembly? For example, my assembly consists of a door, I would like to have one view with the door open and another view with the door closed on the same drawing using the same assembly link.
View 6 Replies
View Related
Jan 14, 2011
I'm having a problem with Inventor 2011 professional on a 64Bit machine. I can make any size assembly with no problem but as soon as I go to make an idw the program crashes and shuts down. It doesn't matter if the base view is one part or 1000 parts as soon as I go to place the view inventor shuts down and I get an error.
View 9 Replies
View Related
Sep 22, 2004
after the first constraint I can't drag the part,
only thing i can do is use the rotate command
View 9 Replies
View Related
Mar 13, 2013
I have been working with macros basically making user forms to control the models. The program calls on a part that I use as an actuation template (its just a part with parameters that are then linked to the assembly contraints) then the macro will change the parameters and update the model.
What I need to do is to put in some code in the userforn initialize sub that gets the actuation template from the disk, for example: C:Other StuffActuation Template A.ipt. Then the macro places the part into the assembly. The userform then manipulates the actuation template (and the assembly model). Then when the userform is unloaded the part is deleted from the assembly.
View 1 Replies
View Related
Aug 29, 2012
I starting out new to Inventor 2013.What are the steps to place a washer and bolt from Content Centre into the assembly?
View 5 Replies
View Related
May 7, 2013
I have created an assembly with multiple views to show the multiple configurations of our products. However, half way down the line I realized I had forgotten to place a component. When I placed the component, I found that it had been placed in all the views automatically. Is there a way to select the views to place the components in or to prevent the component from being placed in any of the custom views except the default view?
View 2 Replies
View Related
Aug 26, 2013
I use a "dump assembly" of assemblies to create cut lists. I throw in multiple copies of each assembly for the job. Sometimes it can be 100 or so of each.These are not placed in any way and could be all placed at the origin. This is only for the parts list and servers no other function.
Any way to place multiple instances of an assembly at once?
View 9 Replies
View Related
