AutoCAD Civil 3D :: Digital Record Of Existing Road Lane Slope

Feb 6, 2013

Civil 3D 2012 (or Civil 3D 2013)

Without automation development, what is the procedure to get a digital record of the existing road lane slope?

I recommend the following:

1

Use the OverlayWidenMatchSlope1 rehab subassembly to build a corridor, targeting the existing road surface

2

Make a report using Corridor > Feature Line Report, reporting the Links to get the slope

Am I correct?

View 3 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: How To Match Gutter Slope To Outside Lane Super Subassembly Slope

Mar 22, 2011

Can't figure out how to match gutter slope to outside lane super subassembly slope.  Have super eop targeting a feature line with elevations, but when i check section editor gutter slope doesn't match pavement slope.

Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600

View 9 Replies View Related

AutoCAD Civil 3D :: Shoulder Subassembly That Varies Slope In Relation To Lane Superelevation Slope

Jan 22, 2013

i need a shoulder subassembly that varies slope in relation to the lane superelevation slope. i know that i can get a subassembly for the shoulder that will follow the alignment superelevation xml data but in my case i can't use it because we are just adding a shoulder to an existing road. we're not changing the superelevation of the existing road, just milling and overlaying and widening. right now i've created a profile of the outside edge of the shoulder that gives me the correct shoulder slope but whenever i change my centerline profile i have to redo the shoulder profiles which is a real time suck.

View 9 Replies View Related

AutoCAD Civil 3D :: Target Existing Surface Beyond Edges Of Road / Sidewalk?

May 15, 2012

if i want to target the existing surface beyond the edges of my road/sidewalk, should i use the link slope to surface subassembly at both ends? i want the model to test if in a cut or fill situation, and then target.

Civil 3D 2013 SP1, Win 7-64 bit
12GB RAM

View 1 Replies View Related

AutoCAD Civil 3D :: Create Assembly That Give Volume Of New Shoulder Along Existing Road

Apr 10, 2013

I need to create an assembly that will give me the volume of a new shoulder along an existing road, as show in this picture.

I can easily make an alignment along my edge of pavement, and match the existing elevations, but I need to hold the cross slope constant AND the shoulder slope constant, and have the bottom of the shoulder slope to a target 2 feet off of my ROW.

View 1 Replies View Related

AutoCAD Civil 3D :: Data Of Existing / Future Ground And Station On Profile Of Road

Dec 18, 2013

How to get automaticly data on the profile. See my road profile in attachment.

Now i have to manually write data of elevation of existing and future ground and distance.

i think that is possible automaticly, but i dont know how.

View 2 Replies View Related

AutoCAD Civil 3D :: Existing Cross Section Slope Labeling For Corridor?

May 4, 2012

how to have exisitng cross slopes display on a bank of corridor cross sections...I see lots of posts on this but I am having trouble finding the answer.  The link below from Add a section view grade label only adds "A" slope label.....I want all of them in all of my sections.

[URL]

View 6 Replies View Related

AutoCAD Civil 3D :: Model Road / Ditch Along Road

Aug 21, 2013

I need to model road with same elevation. But also need to model ditch along road which has a slope of 0.2%. how can i make a ditch with slope.

View 2 Replies View Related

AutoCAD Civil 3D :: Profile Geometry Editor - Slope-Slope Intercept To Place PVI

Aug 20, 2012

Can you not perform a slope-slope intercept to place a PVI?  Essentially holding the sta and elev of the PVI's directly before and after the PVI of interest and changing the grade in and out so that the sta and elev of the PVI of interest are changed.

View 2 Replies View Related

AutoCAD Civil 3D :: Slope To Depth Of 10 Feet Than Change To 2:1 Slope

Aug 13, 2012

I am in the process of transitioning from land desktop to Civil 3D. I design roads in steep terrain and sometimes need to have my catch (daylight) slopes change. So my question is, how do I change a daylight slope at a specified depth? For example, from the shoulder of the road I want a 3:1 fill slope to a depth of 10 feet than change to a 2:1 slope until it catches the existing surface. Can this be built into a subassembly such that if the fill is less than 10 feet it will daylight correctly at a 3:1 and if the depth is greater than 10 feet then it carries the 3:1 for 10 vertical feet and then changes to the 2:1 until it daylights?

View 9 Replies View Related

AutoCAD Map 3D :: Adding Geometry To Existing Feature Record Through FDO?

Aug 28, 2012

I'm running Map 2012 64 bit on Windows 7.  I've connected to an sdf file through FDO.  In the sdf file, it has points representing where people live.  Some of the records have the person's information, but no point associated with it.  Is there a way to add a point to an existing record through FDO?  Typically, i'll create a new point, then re-enter all the data i need for that person and then delete the old record. 

View 4 Replies View Related

AutoCAD Civil 3D :: Lane Outside Super Elevation

May 26, 2012

Superelevation curve criteria specifies axis of rotation but the assembly does not contain pivots. 

okay i got this Before , just when i wanted to change in the Super Elevation Wizard , to outside lane rotation , i recently used AOR type , but yet no luck. also in my profile the super elevation the Cross slop Band : i always no matter what a rotation about center line.

View 1 Replies View Related

AutoCAD Civil 3D :: Widening Travel Lane

May 3, 2012

I've used the OverlayWidenMatchSlope1 subassembly to widen a new travel lane using the existing carriageway crossfall  then I try to create another lane using the same assemble following the same slope but the insert point always starts on the existing ground rather the new levels from the first new widening lane.

View 3 Replies View Related

AutoCAD Civil 3D :: Import Lane Toward Crown Subassembly

Feb 22, 2012

I tried to import the Lane Toward Crown subassembly to my Lanes tab, but the import function looks for *.pkt files and all I have in the Stock Subassemblies folder are *.vb files.

How can I get the *.pkt files?

View 2 Replies View Related

AutoCAD Civil 3D :: Add A Lane Widening To Offset Alignment

Apr 18, 2012

Im using civil 3d UKIE 64bit, having a serious problem with adding a lane widening to an offset alignment. It is a straight alignment approx 200m length, but when i enter the parameters that is asked, at the end it says no solution!

View 2 Replies View Related

AutoCAD Civil 3D :: Subassembly Composer - Lane Assembly Targeting

Nov 19, 2013

I create Curb Return Fillet assembly with shoulder in SAC , but now i have problem with targeting , when i giving two targets it takes only first target and ignores second,   could you check attached assembly and drawing ?

View 4 Replies View Related

AutoCAD Civil 3D :: Pavement Thickness Taper (not Lane Width)

Aug 1, 2012

I have an "ultimate" profile that has be set for a proposed roadway the first 1500' of the roadway will be constructed at this final profile while the last 900' will be constructed for an interim design not at the full depth pavement. So my typical for the final is 9.25 inch of pavement over 14" of stone and the interim is 4" over the same 14" of stone when we transition from the 4" to the 9.25" we are using a 20:1 taper the question is how to model this taper condition and have you had any success.

View 1 Replies View Related

AutoCAD Civil 3D :: Overriding Superelevation Using Outside Lane Elevation Method

Oct 23, 2013

In my corridor I have used superelevation.  In a horizontal curve which has a cross slope of 4.5%, I have an intersection.  To allow for a smoother ride through a few lanes in the intersection I want to change the cross slope from 4.5% to 1%.  I was planning on doing this by using a Outside Lane Elevation Method of a Profile.  However, it appears that my super has precedence over my profile.  Is there are way to make this work?

View 2 Replies View Related

AutoCAD Civil 3D :: Lane Sub Assembly For Varying Cross Fall

Nov 18, 2011

I need a sub assembly for a lane that you can specify varying cross fall. i.e it starts at -2.5% and ends at +2.5%.  

View 3 Replies View Related

AutoCAD Civil 3D :: Superelevation For 1-Lane Ramp (different Shoulder Widths)

Apr 3, 2013

 I'm attempting to use the Superelevation tool on an interchange.  I have 4, 1-lane ramps that I need to apply superelevation to.  The three issues I have (so far) are:

In the Calculate Superelvation Wizard...

1. In Roadway Type, I don't know what to choose, I'm leading toward Undivided Crowned (center Baseline ) because my assembly (as of right now) is set up as an undivided crowned roadway (with the crown on the west travel lane edge). Which Roadway Type I should choose (for a 1-lane Ramp with different shoulder widths?)

2.  Moving on to the the Lanes category doesn't matters.  I uncheck symmetric Roadway, hoping I can choose "0" for the number of lanes on the Left, or at least put the lane width down to "0" but can't do either.  I uncheck the Symmetric Roadway and it still makes everything symmetric (it acts as though it is still checked?) I only want to show a single 15' lane.  (I even tried to use undivided planar, and put both lanes at 7.5'each, but then I still have shoulder issues...)

3.  Move to the Shoulder Control.  Why doesn't it give me the option to do different shoulder widths?  On ramps it is very common (at least in Wisconsin) to have an 8ft shoulder on the right and a 4ft shoulder on the left.  How can I type in 2 different shoulder widths.

View 2 Replies View Related

AutoCAD Civil 3D :: Cul-de-sac / Ability To Link Transition Lane To Alignment

Apr 7, 2005

I watched the cul-de-sac placewhere and I seem to missing some functionality shown. Specifically the ability to link a transition lane to an alignment and profile via corridor properties>logical name>no width shown as the placewhere shows?

View 8 Replies View Related

AutoCAD Civil 3D :: How To Create Median / Lane / Sidewalk Offset Target

Jul 21, 2013

How to create multiple offset target. It mean lane, median, sidewalk extra. I have attached exactly what i expect.

View 3 Replies View Related

AutoCAD Civil 3D :: Cross Section - Wall Move With Lane Transition

May 16, 2012

I have an assembly that contains a basic lane tranisition with a retaining wall next to the road.  I have created an alignment for the lane transition to follow but the wall stays in the same place.  Shouldn't the wall move with the lane transition?  The sub assembly are inserted connecting each other.  what am I missing?

View 8 Replies View Related

AutoCAD Civil 3D :: Autodesk Subassembly Composer 2013 - Lane Outside Condition?

Jan 31, 2013

Does the 2013 subassembly composer include a way to include a condition based on LANE-OUTSIDE-SLOPE?

The figure below indicates the type of condition I would like to include (red arrows).

View 5 Replies View Related

AutoCAD Civil 3D :: Targeting Offset Alignment Layout Profile With Corridor Lane Assembly

Jul 19, 2012

For some reason I cant seem to target an offset alignment layout profile with my corridor lane assembly.  I can target the existing the existing groundprofile with the same  offset alignment, but the layout profile when targetted does not change the lane in my cross sections.  I can do this with civil 3d 2010, but not 2012.  I have tried other lane sub-assemblies and it doesn't make a difference.

View 9 Replies View Related

AutoCAD Civil 3D :: Create All New Existing Surface Over Existing Ground

Sep 28, 2012

I'm trying to create an all new existing surface over existing ground. I have a TIN surface of the EG, and I have drawn overlay splines that describe the new surface, but how to go about creating that design surface.

It is a compound surface, open on one end and closed all around on the other, somewhat like a half of a football stadium, but with an irregular upper edge because I am needing to figure out cuts and fills to manipulate the EG into this new surface without costly major terraforming. There is about 40-50' vertical elevation between the "field" and the upper rim with a generally constant 7-10 deg. slope all around. I'm just at a loss to figure out how to approach this project, and am quite new to Civil 3D.

Civil3D 2013
MacBookPro 17 - 2.4GHz Intel QuadCore i7 (Late 2011 build)
Microsoft Windows 7 64bit
350GB Bootcamp volume

View 2 Replies View Related

AutoCAD Civil 3D :: Road Surface Becoming Flat?

Jan 30, 2013

running an assembly in to the road corridor and creating a surface. i have designed a network of Roads in CIVIL 3d in which whole network is surrounded by a Loop road. The loop road cross fall is unidirectional (2%) and 4.5 wide. I have used LaneOutsideSuperWithWidening subassembly to create  the assembly of the road. This doesnt contain any kerb or footpath but only road channel lines, The corridor run soomthly but after creating the of the loop road corridor the surface is becoming flat meaning there isn't any cross fall acoss the road but in the assembly crossfall is there. If i run the same assembly in another road alignment the suface is coming absolutely correct.

I also tried different road assemblies to run along the loop road but the result is same no cross fall across the road.

View 2 Replies View Related

AutoCAD Civil 3D :: Road Alignment Label

Feb 1, 2012

I am working on Street Improvement Plan using Civil 3D 2012. I have my centerline stationing set for major (100') and minor (50'). My street plan is kind of busy with a several call-out/label, leader etc. I want to set my my station for both major and minor with with decimal to read as 1+00 or 1+ 50 as opposed to 1+00.00... How to get rid of the decimal points.

View 6 Replies View Related

AutoCAD Civil 3D :: Road Design File

Nov 4, 2013

Road design civil 3d complete files (Plan, Profile with complete band, Assembly , corridor, sections etc .

View 5 Replies View Related

AutoCAD Civil 3D :: Road Network Surface

Nov 19, 2012

I have make a road network. Then i make a corridor surface using corridor extends as outside boundary. I also create a boundary in the interior side of the roads with interactively tool, and i use it as a hide boundary. The corridor surface look fine but when i am trying to make a finish Ground Surface pasting the corridor surface after Existing Ground surface then the hide boundary of corridor surface make holes in finish Ground surface.

View 3 Replies View Related

AutoCAD Civil 3D :: Multileader Road Runner

May 30, 2013

Is this a desired behavior on a multileader? URL....

Seems to do it for anything that is not left aligned. I think it was present in 2013 as well. I use multileaders for annotations a lot since it is easier to use them with the background masks and borders than mtexts.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved