I tried to import the Lane Toward Crown subassembly to my Lanes tab, but the import function looks for *.pkt files and all I have in the Stock Subassemblies folder are *.vb files.
How can I get the *.pkt files?
I create Curb Return Fillet assembly with shoulder in SAC , but now i have problem with targeting , when i giving two targets it takes only first target and ignores second, could you check attached assembly and drawing ?
View 4 Replies View RelatedDoes the 2013 subassembly composer include a way to include a condition based on LANE-OUTSIDE-SLOPE?
The figure below indicates the type of condition I would like to include (red arrows).
When I use ImportSubassembly API to import my subassembly created by Autodesk Subassembly Composer into my civil project, it reports error-"eFilerError".
the code like this:
atcFile = @"D:9f92eaa4ef514ac982518852e1169932.atc";
itemId = "ab660722-c69d-4ade-b373-0e9f99c94e55";
SubassemblyCollection subassemblyCollection = cDoc.SubassemblyCollection;
ObjectId subassemblyId = subassemblyCollection.ImportSubassembly("TestSubassembly", atcFile, itemId, this.doc.Editor.GetPoint("Select import subAssembly location").Value);
However, it is OK if to import subassembly provided by Cilvil 3D.
Can't figure out how to match gutter slope to outside lane super subassembly slope. Have super eop targeting a feature line with elevations, but when i check section editor gutter slope doesn't match pavement slope.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
i need a shoulder subassembly that varies slope in relation to the lane superelevation slope. i know that i can get a subassembly for the shoulder that will follow the alignment superelevation xml data but in my case i can't use it because we are just adding a shoulder to an existing road. we're not changing the superelevation of the existing road, just milling and overlaying and widening. right now i've created a profile of the outside edge of the shoulder that gives me the correct shoulder slope but whenever i change my centerline profile i have to redo the shoulder profiles which is a real time suck.
View 9 Replies View RelatedIn terms of data passes from one subassembly to another, is the connection point data x,y,z
the only information that is passed on from one subassembly to the next , or is there a way
to access other properties of the adjacent connected subassembly.
What I am attempting to do is to create a subassembly in SAC to get the slope and length of the connected subassembly above.
I've created a few subassemblies with the SAC and I'm having problems with creating corridors.
When I import the subassemblies they always show up named "Subassembly2". Is this due to some installation problem... it wouldn't be a problem but I will be importing a lot of subassemblies and wouldn't mind cutting down my workload...
Another problem is that when I try to reimport an edited subassembly it will not update in ACC3D2010. I read somewhere that one has to restart civil in order for the changes to take place and that DOES work but is there perhaps another, more functional way, of updating subassemblies?
My third question is about corridors. When i try to make corridors with previously mentioned assemblies all goes well, untill (pause for dramatic effect!)... I add regions to the corridor. What happens is that the corridor doesn't model the different assemblies and only uses the assembly I first assigned to the corridor when creating the corridor.
What I'm trying to design is a set of tunnels where the tunnel cross sections and the elevation of the bottom changes.
I am trying to extract feature lines from my road corridor to use as breaklines, and I don't see a center line crown feature line. I have no problem extracting edge of travel ways, etc. but not the crown of the road.
Win 7 64BIT
C3D 2013
when creating a pipe network, and the slope of the pipe end is say at a 35% from start to end, the crown of the pipe is at a 90 degree angle from the invert elevation (straight up). So if I have an invert elevation of 288.3' the pipe crown elevation is at 292.5'. I need to show the end of the pipe crown perpendicular to the invert elevation so that it reads 292.0'!
View 5 Replies View RelatedI have created COGO points from my corridor, there seems to be 2 sets of points ontop of each other along the crown of the road. They are different numbers, so its not the same point twice, why it would do this?
View 4 Replies View RelatedSuperelevation curve criteria specifies axis of rotation but the assembly does not contain pivots.
okay i got this Before , just when i wanted to change in the Super Elevation Wizard , to outside lane rotation , i recently used AOR type , but yet no luck. also in my profile the super elevation the Cross slop Band : i always no matter what a rotation about center line.
I've used the OverlayWidenMatchSlope1 subassembly to widen a new travel lane using the existing carriageway crossfall then I try to create another lane using the same assemble following the same slope but the insert point always starts on the existing ground rather the new levels from the first new widening lane.
View 3 Replies View RelatedIm using civil 3d UKIE 64bit, having a serious problem with adding a lane widening to an offset alignment. It is a straight alignment approx 200m length, but when i enter the parameters that is asked, at the end it says no solution!
View 2 Replies View RelatedI have an "ultimate" profile that has be set for a proposed roadway the first 1500' of the roadway will be constructed at this final profile while the last 900' will be constructed for an interim design not at the full depth pavement. So my typical for the final is 9.25 inch of pavement over 14" of stone and the interim is 4" over the same 14" of stone when we transition from the 4" to the 9.25" we are using a 20:1 taper the question is how to model this taper condition and have you had any success.
View 1 Replies View RelatedIn my corridor I have used superelevation. In a horizontal curve which has a cross slope of 4.5%, I have an intersection. To allow for a smoother ride through a few lanes in the intersection I want to change the cross slope from 4.5% to 1%. I was planning on doing this by using a Outside Lane Elevation Method of a Profile. However, it appears that my super has precedence over my profile. Is there are way to make this work?
View 2 Replies View RelatedI need a sub assembly for a lane that you can specify varying cross fall. i.e it starts at -2.5% and ends at +2.5%.
View 3 Replies View Related I'm attempting to use the Superelevation tool on an interchange. I have 4, 1-lane ramps that I need to apply superelevation to. The three issues I have (so far) are:
In the Calculate Superelvation Wizard...
1. In Roadway Type, I don't know what to choose, I'm leading toward Undivided Crowned (center Baseline ) because my assembly (as of right now) is set up as an undivided crowned roadway (with the crown on the west travel lane edge). Which Roadway Type I should choose (for a 1-lane Ramp with different shoulder widths?)
2. Moving on to the the Lanes category doesn't matters. I uncheck symmetric Roadway, hoping I can choose "0" for the number of lanes on the Left, or at least put the lane width down to "0" but can't do either. I uncheck the Symmetric Roadway and it still makes everything symmetric (it acts as though it is still checked?) I only want to show a single 15' lane. (I even tried to use undivided planar, and put both lanes at 7.5'each, but then I still have shoulder issues...)
3. Move to the Shoulder Control. Why doesn't it give me the option to do different shoulder widths? On ramps it is very common (at least in Wisconsin) to have an 8ft shoulder on the right and a 4ft shoulder on the left. How can I type in 2 different shoulder widths.
I watched the cul-de-sac placewhere and I seem to missing some functionality shown. Specifically the ability to link a transition lane to an alignment and profile via corridor properties>logical name>no width shown as the placewhere shows?
View 8 Replies View RelatedHow to create multiple offset target. It mean lane, median, sidewalk extra. I have attached exactly what i expect.
View 3 Replies View RelatedCivil 3D 2012 (or Civil 3D 2013)
Without automation development, what is the procedure to get a digital record of the existing road lane slope?
I recommend the following:
1
Use the OverlayWidenMatchSlope1 rehab subassembly to build a corridor, targeting the existing road surface
2
Make a report using Corridor > Feature Line Report, reporting the Links to get the slope
Am I correct?
I have an assembly that contains a basic lane tranisition with a retaining wall next to the road. I have created an alignment for the lane transition to follow but the wall stays in the same place. Shouldn't the wall move with the lane transition? The sub assembly are inserted connecting each other. what am I missing?
View 8 Replies View RelatedFor some reason I cant seem to target an offset alignment layout profile with my corridor lane assembly. I can target the existing the existing groundprofile with the same offset alignment, but the layout profile when targetted does not change the lane in my cross sections. I can do this with civil 3d 2010, but not 2012. I have tried other lane sub-assemblies and it doesn't make a difference.
View 9 Replies View RelatedWith using superelevation wizard in Civil 3d 2012, changing the lane width is not affecting the resulted values of transion length and run-off length, Is that correct ? ( as civil is using standerd AASHTO tables which assume that lane width typically is 3.6m )
Also, There is only 2 tables for 2-lanes and 4-lanes roadway, Is it for total road width or for one directon only, and what about different no. of lanes ?
Is it possible to add a base depth to the transition lane assembly? I need to do volumes for my road, (pavement, base) but there is a section with a transition (which only has one depth), so that section is off.
View 5 Replies View Related(in Inventor Pro 2014,64 bit):
I've made an stairs assembly that contains adaptive parts that are all controlled by the assembly parameters.
Here is my assembly and the controlling parameters. The stringers on the side are made with the frame generator and use the "extend" feature to get the appropriate length, as driven by the parameters. The reason I used frame generator is so that I can easily change sizes of the stringers down the road, if needed. I chose to make the parts associative so I could control all of the parameters from within the assembly instead of opening each part separately.
My goal now is to be able to use this assembly (or something similar) as a template to create new sets of stairs, all to be placed in the same main assembly.
I attempted to duplicate all of the parts (append a "2" at the end of each file name and replace components in the new set of stairs with the 2nd version) but ran into problems with the two stringers. I can't figure out what to do to get the Frame00001 and Skeleton00001 to reassociate to Frame00002 and Skeleton00002. So any time I change my slope, the original stairs will end up trying to copy the new stringers instead of keeping the old ones.
how can I make this assembly reference a new frame, and secondly?
How can i join these 2 pieces of crown moldings? I've created them in polyline and then extruded them.
View 5 Replies View RelatedHow can I create a subassembly..AND hot to add a Pave 3 option or another subbase depth.
View 9 Replies View RelatedWe are trying to edit a small portion of an existing corridor by adding a generic daylighting subassembly. The add subassembly tool in the Corridor Section editor works, but we get an error because the new sub doesn't have a target surface specified. how to add a target for a sub that is added after the corridor was created?
Civil 3D 2012 & 2013 & 2014
Toshiba Qosmio X505-Q890
2 x i7 - Q740 quad core CPU's
8GB of RAM
60GB SSD + 500GB HDD
NVidia GeForce GTS 360M - driver 8.17.13.0697
Win 7 Home Premium
I need to transition to one subassebly to another. The first subassembly is at existing ground the other assembly is above ground. See following picture:
I need to transition from station 12+50 to 13+50. See following picture:
Here is a picture of the Corridor Properties:
Do I need to make a different subassembly in between the two stations? Is there a command I am not seeing that does it for me?
I know this sounds like a really stupid question. Where is the subassembly composer? We have Civil3D 2013, and my understanding was that the subassembly composer was supposed to automatically install in 2013 as opposed to previous years when you had to download it from the Subscription Center.
C3D 2013
64-bit