I am designing a fill volume. I have created my surfaces and feature line. My topos however are on two seperate layers as one is existing ground and the other is engineered ground. How can I get my grading to work using two layers in a grading group?
View 5 RepliesI have this problem when creating grading groups with more than one feature line in them. It seems really unstable when you trying get the grading to connect. I have tried to create two separate grading groups in one site or two feature lines in one grading group. And the result is the same, the grading that will be create can sometimes look oki, but suddenly they tend to disappear or look weird...
View 4 Replies View RelatedWhen a file has many surfaces, gradings and sites manually delete them is slow ¿is there a method to select multiple sites, surfaces and gradings on prospector and delete them all at once and not one by one?
View 1 Replies View RelatedI have two separate graded levees in my drawing. One has created a surface just fine, the other absolutely refuses to generate a surface. I've deleted the grading even the feature lines and re-did them. In my grading group I have automatic surface creation checked and the volume base surface checked. I show the surface in the prospector but there is nothing there. The one levee will show contour styles but this one ZIP!
View 2 Replies View RelatedI have an Existing Surface i created from survey data. I have a Proposed Surface i created with feature lines. Now i want to create grading around the outside portions of my Proposed Surface. I create the Grading Group and specified a projection surface and selected a Criteria Set for a 3:1 slope to match back to Existing Surface. I select the Feature Line i wish to create the grading from and progress through the cut and fill prompts and nothing happens. Nothing gets created. I have tried an audit on the drawing to see if errors are causing the problem and there are no errors.
I use this tool all the time and this problem comes up frequently. Especially if i have made any surface adjustments.
I'm trying to replicate a dump surface from a cad file, but this one is rather different from what i'm used to (more simple and poligonal).
This one is curved and the top of the platform has inclinations has the picture shows.
I'm having trouble on finding the best way to aproach this dump surface. I tried to start from point 2 with the curved feature line and grade back 2% till EG and then grade forward 10% till it reaches point 3 at elevation (900) , but when i grade forward the sides obviosly dont hit my EG.
I have 2 feature line and need to create a 3Dline from 2% slope from both of them.
Not to mention I have more that 100 feature line like these.
how to use Civil 3D to create a grading plan for a solar PV site or a golf course?
Here is the situation. We have a large 100 acre site that is not flat. We want to do minimal grading to "smooth out the surface". So that maximum slope on the site is 10%. The site does not have to be graded completely flat. We are trying to work with the existing contours and terrain as much as possible.
Is there some functiion or some way for Civil 3D to "smooth out a surface"? We want to work with the existing slopes and contours of the site and just need a grading plan that will smooth out mounds, holes, or high slope areas.
"An infill grading has no criteria applied to it. Any area bounded by feature lines or lot lines that is not already a grading can be converted to an infill grading."
So given an area enclosed by a feature line, an infill grading can be created. Using the same features line, an feature line grading can also be created. what is the difference between these two surfaces? They both have no criteria applied to them.
I have a Grading Plan that is getting increasingly unstable as time goes on... I used Grading creation tools to create 3:1 mounding for a stock pile that is on my site... there are a couple dozen mounds on the site for this stock pile...
My problem is when I go to edit any feature lines or Grading; the drawing just crashes and will not save my work... I ran an audit and it does not find anything... I need to get the grading done ASAP and this is a major hold up... Do I need to go back through and manual grade everything or is there a secret that I am missing?
I have read multiple forums on the matter with older version of Civil 3d... so this is to tell me that the problem has never been fixed with Autocad?
When we apply surface projection gradings to feature lines, we get locked vertices on the feature line wherever the grading transitions from cut to fill. In turn these vertices create segments in the feature line which influence any labels applied to the line. I don't want a bazillion segment labels on my FL. I only want segment labels between the physical vertices and elevation points. Is there a workaround or is an enhancement request in order?
View 9 Replies View RelatedIs there away to link a i.e. (a stoop to a finish flood elev)? So that, if I were to raise the finish floor, the stoop would move also. I understand I could possible to a create grading feature line for a stoop, but what happens if the stoop would be irregular shapped and not a rectangle?
View 5 Replies View RelatedI have feature line with elevations that represents bottom of ditch and want to go UP 3:1 slope. also i have edge of road feature line that is higher than ditch and want to go 2% down until it hits side of the ditch that is 3:1. Any easiest way in civil 3d to create intersection line between ditch bottom going up 3:1 and edge of road going down 2%?
View 2 Replies View RelatedI want to create a Layer Filter that excludes both Civil Layers and Xrefs.
I have created one that excludes Civil objects (Excel Civil.jpg) but when I add a filter for excluding xrefs as well the Civil objects appear in the filter again indeed all the layers are included again (Excel Xref.jpg) if I invert the filter nothing is displayed.
I'd like to use boxes to punch holes into the layered artwork below them. I want the result to look exactly like this image, but with the white boxes being transparent holes.
This seems so simple, but I can't find any combination of layers/pathfinder tools/compound shapes/or clipping masks that will produce this result. No matter what, I end up losing part of the artwork (usually the topo lines and the black bar).
I can't figure out the proper commands to fill out and complete the script below. What I am trying to do is:
- Create a new document using one of the Profile presets (or have the New Document dialogue open so I could select the profile, size and bleed)
- Make 3 layers, each with a diferent name
- Create a rectangle the size of the artboard on the bottom layer, with a swatch stroke and no fill
- Create a rectangle the size of the bleed on the middle layer, with no stroke or fill
Like I said, I haven't gotten far at all. I've read through the basic scripting guides and I'm just not understanding all of the language needed to string things together.
tell application "Adobe Illustrator"
make new document
set topLayer to make new layer ¬
at beginning of document 1 with properties {name:"Vector"}
set bottomLayer to make new layer ¬
at end of document 1 with properties {name:"Through Cut"}
end tell
I am trying to create a proposed surface using grading. I created a closed polyline representing the site's outer boundary then created a feature line from it. When I try to select the feature line in order to create the grading I get "THIS FEATURE OVERLAPS ITSELF AND CANNOT BE GRADED".
View 1 Replies View RelatedWhen I create multi sect views they plot 3 rows from left to right shown below:
0+00 1+00 2+00
I would like it to plot from bottom to top like shown below
2+00 5+00
1+00 4+00
0+00 3+00
Is there somewhere to adjust the settings?
I am creating plan sheets and using the sheet creation tool. The plan sheets I am looking to make have stacked view, similar to a plan and profile sheet, only they have the horizontal alignment in both views.
I have a template set up with two viewports, but when I try to create the sheets it puts the same view frame in both of the viewports. Is there any way to set this template up so that I can have, lets say, STA 100+00 - 110+00 in the top viewport and then STA 110+00 - 120+00 in the bottom viewport. I understand that I can move the viewports once they are created, but I would rather have that done automatically. I am not sure if what I want done is possible with Civil 3D.
how (or if it is possible) to create a profile that contains mutliple segments. THe scenario I have is a proposed profile that ties to existing grade and then picks up again at existing grade some distance down the alignment.
The only way I can find to do this now is to create it all as one profile with no breaks and then go back and remove the profile segments in between the existing grad tie ins. Except when I remove a segment from my profile all of the labels beyond the first segment fo away.
In the past I have been creating multiple profiles but seeing as how long this surface alignment is and how many breaks in the proposed profile there are I would rather have just one proposed profile than several, especially when labeling existing/proposed elevations in the data band.
Here is an example before a segment is removed:
And here is an example after the segment was removed, the green labels are just polys and mtext not C3D entities
Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU
16GB RAM
I have the need to put COGO points along the vertices of multiple 3D polylines in a DWG. I know how to do this individually for each 3DPL via the "Points>Create - Miscellaneous > Polyline Vertices - Automatic" or "CREATEPTPLYLNCTRVERTAUTO" command. Need tip on how to do this in a batch format for all the selected 3D PLines in the drawing without having to select each individual 3DPL and having to hit return to enter a description for each individual vertex? I can do without having to add a description and can leave each description blank or enter the same description for each.
I'm Using C3D2013.
Can I create a pipe network from multiple objects?
For example, I have 10 feature lines that I want to use to create one pipe network. Instead of creating 10 pipe networks one at a time, can I create one pipe network all at once?
I am attempting to create section views from a corridor. I have about 80 sections total that I would really like to stack 3 high...then just across the page. Any step by step that make this process easy to understand?
Right now I get 10 high then across the page (using 'draft' option). I've tried to make a dwt at a 10 scale, (setting the viewport at 10 scale and viewport as a 'section' in the properties), but when I use that, the sections start overlapping (this is using the 'production' option).
When creating multiple section views with production as the placement option, all the sections superimpose on top of each other. Attached graphic.
I tried to attach the .dwt file used for the multi section view, but the site doesn't allow upload of file extension .dwt.
C3D 2012 SP3..I want to label the subassembly I have created. It is easy enough to create the label style and apply it through the code set styles. I want to drag the labels for pavement depth, creating a leadered situation. Why does the program create multiple labels for each marker or link? Can this be limited to one lable for the marker and link?
View 2 Replies View RelatedI am creating my Final Grading surface with from 2 surfaces - a proposed road surface and a proposed grading surface. (Note of roads within the road surface)
The issue is that when I paste the proposed road surface (that consists of several looped sections) over the proposed grading surface, the proposed grading surface within the looped road areas dissappears.
I have tried several options using boundaries for the inner looped areas on my road surface, and has altered my order of opterations for my final surface edits, and many other things also.
I have attached an image for reference.
Is there an easy way to raise an entire site by 1.0 foot and have the grading hit the previous targeted surface? The only way I have found is to grab all the feature lines and raise them up by the required amount, but by doing that, the grading bogs down my system and it crashes, plus, I have grading attached to 3dpoly's and not necessarily all feature lines.
View 1 Replies View RelatedI am drawing a pond levy. I draw the outline of the top of the fill, set that at the elevation I want, then grade it down to the existing surface on a 6:1. The grading works perfectly. The outline of the fill's footprint shows up just fine around the back of the fill, but the toe line doesn't show up all along the front side of the fill, but I still get the slope lines projecting down in the front.
View 8 Replies View RelatedI want to cut a channel through a existing surface; bottom width: 5 feet; at elevation 1950 and side slope 1:1 (45deg) up to existing ground.
What I am doing right now is create a feature lines 5 feet wide, at el 1950 and use grading tool to project it to existing ground with side slope at 1:1. What i am doing is correct?
I am working with Civil 3D 2014, I played with 2009 back in 2008 and before that it was Land desktop. I don't know if I am not following a standard workflow.
Build the EG from contours.Layout the CL for the ROW and convert to a horizontal alignments.Create the profiles.Design the vertical alignment in the profile.Create the assemblies for the different types of road sections.Full profile, pavement width assembly, the curb return assembly, the daylight left / right, 1/2 side left / right, and pavement width left / right.Build the corridor, set the target surface as EG or FG, depending on where the section of the corridor is located. (At the edge of the property to EG, then after the first building pad to FG)This is where I have a thought something is wrong. If I am grading the entire site, why would I have the ROW grade to the EG, when I will need the surface to grade from the ROW to the closest building pads?Create the intersections, using the different types of assemblies, per the ROW sections.Create feature lines and use elevation editor to set all the elevations around the pad.Using the Grading creation tool, grade to surface, using a 2:1 side slope. Then adding an infill to the pad.
I keep having the file crash after grading about 10 lots. I recover and it works find, but then the file runs very slow, and will crash. I haven't taken any classes in Civil 3d, and am looking for one in my area.
I am use to creating the vertical surface then creating points along the CL, TBC, FL, BOW then creating break lines along the points. Then create a break line for the pads, and build the FG contours from these break lines.
Say I have a grading that runs north south and goes down 2%, up 2% and so on waffling along. Is it a poor practice to trace the side edge of the grading (in the same site) to add another grading to pitch east west?
View 4 Replies View Related