When creating multiple section views with production as the placement option, all the sections superimpose on top of each other. Attached graphic.
I tried to attach the .dwt file used for the multi section view, but the site doesn't allow upload of file extension .dwt.
When I create multi sect views they plot 3 rows from left to right shown below:
0+00 1+00 2+00
I would like it to plot from bottom to top like shown below
2+00 5+00
1+00 4+00
0+00 3+00
Is there somewhere to adjust the settings?
I am attempting to create section views from a corridor. I have about 80 sections total that I would really like to stack 3 high...then just across the page. Any step by step that make this process easy to understand?
Right now I get 10 high then across the page (using 'draft' option). I've tried to make a dwt at a 10 scale, (setting the viewport at 10 scale and viewport as a 'section' in the properties), but when I use that, the sections start overlapping (this is using the 'production' option).
I am trying to use plan production to generate sheets for a long, skinny corridor. I wanted to put two plans onto a single sheet.
I have tried a few settings, but get a duplicate of the same plan. Is this possible, or is necessary to do it manually.
How can I create a dwt file for the production of multiple section views sheets in A3 format and 1/200 ?
Civil 3D Section .dwt (Template/plan production) has only layouts for A0 and A1 plan and scales 1/500 - 1/1000 and 1/5000. I tried to change the format to A3 and scale to 1/200 of one of those layouts in the set up manager but didn't get a good result while producing section sheets.
When i am creating section sheets from multiple section views ,section sheet view port scale changes.I did set it correctly in my template.
For example it changs from 1:150 to 1:150_1
Then in section sheets scetions views are not displaying correctly.
When i change view port scale manually it shows correctly.But it should do to all sheets.
What should I do?
In model spacr multiple section views are showing correctly.
AutoCAD Civil 3D 2012 SP 2
Sri Lanka
how to get the sections to center or to add a x, y offset distance.The only options I have found for placement are lower left, lower right, upper left, upper right.
View 1 Replies View RelatedWhen creating multiple sections using the draft option what settings control how the sections are placed? For example, 5 across, 4 down.
edit - I have several alignments. One that has 8 section views is created with 4 across and 3 down, another with 18 sections is created with 5 across and 4 down and a third with 34 is created with 6 across and down. I'd like to be able to control this if possible.
Every time I try to create multiple section views in Civil 3D 2014 the system hangs and never generates the views. It looks as if it's processing but it never stops and never generates.
View 4 Replies View RelatedI am working on a corridor project where I have to make section views of the road. I created my sample lines by range of stations, and made all of my section views from there. Now I need to add volume tables for each section view.
I have 28 section views, and more to come when I do another set of sample lines for another road, and I don't feel like going through each section view individually to make volume tables for them.
Is there a way I can create total volume tables for all of my section views at the same time? It would save a lot of time!
I have created multiple sections and produced drawings, but now need to amend the design and provide 1 additional section on the drawings. I added an additional sample line to the sample line group and then updated the secion view layout but the additional section did not show in the multiple section view. Is there a way to add the additional section to the existing multiple section view? or do I need to go through the process of deleting the current sections and creating a new multiple section view that includes the new sample line?
View 1 Replies View RelatedThe new features in 2014 does not work. I can project solids to a section view but not to multiple section views.
View 1 Replies View RelatedI have projected objects to multiple section views (ProjectObjectsToMultiSect) but now I want to remove them all. How do I remove all of the projected objects?
I can select an individual section view and go to the Projections tab in the Section View Properties and uncheck the projections, but how do I do this for all the views at once.
Sometimes when i creating multiple views (sections) in section display option page there are nothing displaying.(surfaces).
View 2 Replies View RelatedI am trying to use the plan production feature and I've got it working pretty well except when it creates the profile view, it cuts off the data band and also makes the viewport at the very top edge of the profile, so in the viewport I can't see the data band or the top edge of the profile view.
What setting am I missing to make it show the data band?
Civil3D 2014 SP1
Win 7 Professional - 64-bit
HP Z400
Xeon W3550 @ 3.07Ghz
24GB of RAM
Nvidia GeForce GTX 760
I have lots of section views with some surfaces and pipes. Unfortunately, in a number of section views pipes are not shown in full height because the section view level range is too little. What I am wondering is - is it possible to automatically adjust section level ranges so that they fully include pipe sections? Please see also the image in the attachment.
View 2 Replies View RelatedI am trying to create a second base view (using Layout/Create View/Base from model space). The problem is, I need it to be rotated from the original base view. However, when I rotate the part in model space, ALL of my views change.
So I guess my question is, how do I create multiple views of the same part that are seperate from the other base views?
In my section editor my labels show up correctly and in all the locations I want. But then, in my cross section file, I look in my section views and they are completely different. When I try to label more points under the Code Set Styles, they won't even show up on my section views.
View 6 Replies View RelatedI think I just haven't done this in a while and can't find the right setting.
I have existing sections.
I have section views.
I created a corridor.
How do I add the corridor section to my existing cross-section in the section views?
I can view them in the corridor section editor. But I should also be able to add the corridor section to my section views, right?
To plot them, do I NEED to do this through Sheets Sets? I don't have experience with sheet sets yet.
I don't use Civil 3D often enough anymore. Still learning much about the new interface and pulling a design together.
I am trying to create section views to track beach erosion. I have created an alignment and sample lines successfully. The shorter sections look as they should. The longer sections are a mirror of themselves (ex: a section that should be 529' in length is drawn as 1058'). Is this a matter of needing to create a corridor and going the other processes that normally have to be done for a road or is there something else I am missing here?
View 7 Replies View RelatedI'm working with civil 3d 2012,I'm trying to find a solution for the following problem,in Civil I have an alignment of 2kilometer and they want a section view every 5 meters,
automatically I can create over 500 section views, no problem there,but then I want to plot these 500 section views to a png file,and to do that I need to get all of them in separated layouts, for which there also is an automated function but its stops at 255 layouts,I've done 4 km in split up drawings..I've got 40km left no option splitting it up in 1 km sections.
I can get all of the same section views on the same page. I'm using sample line group
View 1 Replies View RelatedI have the task of creating elevation views of a site. These views require that the model be clipped along a section line to crop the forground so it doesn't obstruct the view of the site.
I've experimented with the section plane tools in the 3D modeling workspace but I can't get a section view. I suspect it is because they don't work with C3D surface objects. Any workflow for this task? Ultimately I need to generate hard copies of the views for the architect to use for his landscape plans.
When i bring my section views in, the cross sections display on top of each other, i attached a screen capture.
View 2 Replies View RelatedI'm currently doing some testing of 2014 SP1 and noticed the Copy Styles routine when creating Plan Production Sheets doesn't seem to function as it did in 2012?
Using 2014 SP1, I data referenced a Pipe Network into a Plan Prod. sheet that was created before the Pipe networks were created. After data referencing the first Pipe Network into the plan sheet, I tried to label my pipes and structures, noticed none of our custom styles got copied (during create sheets command) into the sheet?
In 2012 they did.We have a lot of these Plan Production dwt's here and it's going to be a major PITA if all Plan Production.dwt's will need to have all Styles within them.
The nice thing about the way it used to work is the styles only needed to be maintained in a couple base.dwt's.
In addition to these Pipe & Structure label styles missing the list goes on throughout the Settings tab. Only present styles seem to be of "in use" nature such as pfl style, Alignment style, pfl view style etc. where the sheet creation process pulled specific information into the sheet dwg from source dwg.
Also did a quick test of our 2012 configuration and majority of , if not all, styles from source dwt do get copied over eliminating the need for them within the Plan Production dwt's. 2012 SP3 used here.
C3D 2012 SP3 & C3D 2014 SP1
Win 7 Professional 64 Bit
I have section views @ 50 feet along my corridor and i want to show them on a sheet. When i create a viewport, those section views are not display in Layout Tab?
View 7 Replies View RelatedI created a base drawing for sections that references an alignment. I xrefed in the drawing where my corridor was created. When I create the section views, the corridor shows up perfectly.
I then created a blank sheet and xrefed in my section view base drawing.In this sheet drawing, only parts of the corridors are visible.I have a C&G on one assembly and a shoulder on another assembly that aren't visible. (see pics)The first pic is my section base drawing.
I have to represent a road section with limits of houses or any interference on field. All of thees interferences are poly lines, 3dpoly, lines, etc. Is it possible to have a little mark or something like this in a road section, it will work for me a lot for represent the houses in my sections.
View 1 Replies View Relatedhow to make the label information X,W ,Z into the section views as you see in this pictures(Attachments)
pic1: COGO points in the corridor
pic 2: section view
Use:Civil 3d 2012
I am doing public works type project. A simple road widening project. I created an alignment, surface, profile view and basic road assembly (from tool palettes) and corridor.
I created a corridor and referenced it to my "profile view", "alignment" and to "basic road" assembly. When I created section views, it shows only existing grade based on the surface and the basic road assembly is not showing on my sections. I can't figure out how to do it.
“Creating multiple section views” introduces empty section views?
I’m wondering the reason for which the generated section views are empty!
