I have to represent a road section with limits of houses or any interference on field. All of thees interferences are poly lines, 3dpoly, lines, etc. Is it possible to have a little mark or something like this in a road section, it will work for me a lot for represent the houses in my sections.
View 1 RepliesI have lots of section views with some surfaces and pipes. Unfortunately, in a number of section views pipes are not shown in full height because the section view level range is too little. What I am wondering is - is it possible to automatically adjust section level ranges so that they fully include pipe sections? Please see also the image in the attachment.
View 2 Replies View RelatedWhen i am creating section sheets from multiple section views ,section sheet view port scale changes.I did set it correctly in my template.
For example it changs from 1:150 to 1:150_1
Then in section sheets scetions views are not displaying correctly.
When i change view port scale manually it shows correctly.But it should do to all sheets.
What should I do?
In model spacr multiple section views are showing correctly.
AutoCAD Civil 3D 2012 SP 2
Sri Lanka
In my section editor my labels show up correctly and in all the locations I want. But then, in my cross section file, I look in my section views and they are completely different. When I try to label more points under the Code Set Styles, they won't even show up on my section views.
View 6 Replies View RelatedI think I just haven't done this in a while and can't find the right setting.
I have existing sections.
I have section views.
I created a corridor.
How do I add the corridor section to my existing cross-section in the section views?
I can view them in the corridor section editor. But I should also be able to add the corridor section to my section views, right?
To plot them, do I NEED to do this through Sheets Sets? I don't have experience with sheet sets yet.
I don't use Civil 3D often enough anymore. Still learning much about the new interface and pulling a design together.
I am trying to create section views to track beach erosion. I have created an alignment and sample lines successfully. The shorter sections look as they should. The longer sections are a mirror of themselves (ex: a section that should be 529' in length is drawn as 1058'). Is this a matter of needing to create a corridor and going the other processes that normally have to be done for a road or is there something else I am missing here?
View 7 Replies View RelatedI'm working with civil 3d 2012,I'm trying to find a solution for the following problem,in Civil I have an alignment of 2kilometer and they want a section view every 5 meters,
automatically I can create over 500 section views, no problem there,but then I want to plot these 500 section views to a png file,and to do that I need to get all of them in separated layouts, for which there also is an automated function but its stops at 255 layouts,I've done 4 km in split up drawings..I've got 40km left no option splitting it up in 1 km sections.
I can get all of the same section views on the same page. I'm using sample line group
View 1 Replies View RelatedI have the task of creating elevation views of a site. These views require that the model be clipped along a section line to crop the forground so it doesn't obstruct the view of the site.
I've experimented with the section plane tools in the 3D modeling workspace but I can't get a section view. I suspect it is because they don't work with C3D surface objects. Any workflow for this task? Ultimately I need to generate hard copies of the views for the architect to use for his landscape plans.
how to get the sections to center or to add a x, y offset distance.The only options I have found for placement are lower left, lower right, upper left, upper right.
View 1 Replies View RelatedWhen i bring my section views in, the cross sections display on top of each other, i attached a screen capture.
View 2 Replies View RelatedWhen I create multi sect views they plot 3 rows from left to right shown below:
0+00 1+00 2+00
I would like it to plot from bottom to top like shown below
2+00 5+00
1+00 4+00
0+00 3+00
Is there somewhere to adjust the settings?
I have section views @ 50 feet along my corridor and i want to show them on a sheet. When i create a viewport, those section views are not display in Layout Tab?
View 7 Replies View RelatedI created a base drawing for sections that references an alignment. I xrefed in the drawing where my corridor was created. When I create the section views, the corridor shows up perfectly.
I then created a blank sheet and xrefed in my section view base drawing.In this sheet drawing, only parts of the corridors are visible.I have a C&G on one assembly and a shoulder on another assembly that aren't visible. (see pics)The first pic is my section base drawing.
how to make the label information X,W ,Z into the section views as you see in this pictures(Attachments)
pic1: COGO points in the corridor
pic 2: section view
Use:Civil 3d 2012
I am doing public works type project. A simple road widening project. I created an alignment, surface, profile view and basic road assembly (from tool palettes) and corridor.
I created a corridor and referenced it to my "profile view", "alignment" and to "basic road" assembly. When I created section views, it shows only existing grade based on the surface and the basic road assembly is not showing on my sections. I can't figure out how to do it.
“Creating multiple section views” introduces empty section views?
I’m wondering the reason for which the generated section views are empty!
I have searched the Help fine in Civil 3D, I have searched the tutorials and Knowledge Base online, I have searched the Mastering AutoCAD Civil 3D manual, and I can not fine how to turn on hatching in Section Views. I'm currently running Civil 3D 2013.
View 5 Replies View RelatedI am working on a project that contains a main road with on both sides a bike path. From each of these thins I made a profile, alignment, etc. I made one assembly with two assembly offsets, each on one side of my main road. So far everything is going very well, but here comes my problem.
The two bike paths assembly (these are assembly offsets) I want to connect to my road assembly. I found some information about a "marked point" and the "Linktomarkedpoint" assembly. I placed the marked point on my edge of the road and placed the linktomarkedpoint on my bike path. Rebuilding my corridor and when I took a look in my sections, the line between the bike path and road ain't visible. I gave the marked point an unique name and the linktomarkedpoint I gave the same name as my marked point.
I had about 20 cross sections that I created multiple section views for. I added 2 cross sections (one near the beginning, one in the middle).
Can I get these new sections to insert into their proper locations (by station) with a kind of refresh of my multiple section views without having to recreate multiple section views?
I already have the section sheets lined up in viewports on layout tabs. I want to keep everything in the same place. If the only way I can add the new sections is to create multiple section views again, what's the best way to handle this? Draw some kind of cross-hairs in model space when picking where to generate them and pick on the same point every time?
Is it possible to have XS sampled assemblies displayed on individual cross sections? I know that the sample line group properties control which assemblies are sampled and displayed. Say that assemblies A,B and C are sampled and displayed on sections from 0+00 to 3+00. Can ONLY assemblies A and B be displayed on sections from 1+50 to 2+00, and A.B and C on everything else?
View 2 Replies View RelatedI would like to show a pipe network structure on my section view. The catch- the structure is 10' away from my sample line. Is there any way to project structures onto section views? C3D 2011
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit
C3D 2014 SP1
Dell M6600, Core i7 @ 2.3GHz, 16 GB ram
Dell T3500 workstation, too much ram to post
I have created section views of my allignment and corridor in my drawing the problem I have is. In some of the section views there is different parts of the different assemblies not showing up. For example in one section I have my lane then my curb then no sidewalk then blvd. It is not the same in each section view either some are missing one thing while others are missing others.
View 1 Replies View RelatedWhen creating multiple sections using the draft option what settings control how the sections are placed? For example, 5 across, 4 down.
edit - I have several alignments. One that has 8 section views is created with 4 across and 3 down, another with 18 sections is created with 5 across and 4 down and a third with 34 is created with 6 across and down. I'd like to be able to control this if possible.
I am using C3D 2012. I my drawing I have 3D solid objects that I want projected into my roadway x-sections. When I use the menu command to "project objects to section views" and select "solids" I get the message "no objects to project". Are their different types of solid objects in autocad?
View 9 Replies View RelatedI created some about 20 cross sections for a creek we topo'd and then went to work making the topo itself look presentable. After I was all done with that I noticed my cross sections had lost the surface data and were now just an empty grid.
When I go to edit a cross section's properties in the elevation tab the "Automatic" choice has a minimum and maximum elevation of 0. When I use one of those existing sample lines to create a single cross section the same thing happens, it's not picking up data from the surface. However, when I made a new sample line along the existing alignment it picked up the elevations and created a cross section just fine.
Is there anything I can do besides recreating all the sample lines and cross sections? I'm looking for any other way because I have already labled and put in some extra work on the cross sections and I'm hoping to be able to just recreate what I already did and drop them so it will match the linework I already did.
Every time I try to create multiple section views in Civil 3D 2014 the system hangs and never generates the views. It looks as if it's processing but it never stops and never generates.
View 4 Replies View RelatedI am working on a corridor project where I have to make section views of the road. I created my sample lines by range of stations, and made all of my section views from there. Now I need to add volume tables for each section view.
I have 28 section views, and more to come when I do another set of sample lines for another road, and I don't feel like going through each section view individually to make volume tables for them.
Is there a way I can create total volume tables for all of my section views at the same time? It would save a lot of time!
I have created multiple sections and produced drawings, but now need to amend the design and provide 1 additional section on the drawings. I added an additional sample line to the sample line group and then updated the secion view layout but the additional section did not show in the multiple section view. Is there a way to add the additional section to the existing multiple section view? or do I need to go through the process of deleting the current sections and creating a new multiple section view that includes the new sample line?
View 1 Replies View RelatedThe new features in 2014 does not work. I can project solids to a section view but not to multiple section views.
View 1 Replies View RelatedI am attempting to create section views from a corridor. I have about 80 sections total that I would really like to stack 3 high...then just across the page. Any step by step that make this process easy to understand?
Right now I get 10 high then across the page (using 'draft' option). I've tried to make a dwt at a 10 scale, (setting the viewport at 10 scale and viewport as a 'section' in the properties), but when I use that, the sections start overlapping (this is using the 'production' option).