AutoCAD Civil 3D :: Why Corridor Adding A Hinge
Sep 18, 2013
Why is my corridor adding a hinge? [Atleast I think that is the problem]
I am trying to create a berm that is 8' wide. For my assembly I used 4' wide basiclanes and daylightgeneral (with 3:1 slope in all parameters) on left and right side.
In the top image I have circled two of the areas in which the hinge line is shown. And in the bottom right the cross section of one side of the berm is shown. As you can see on the inside (left) there is two feet sloped at approximately -1% before it daylights to the surface at 3:1
Why isn't the left side matching the right?
View 4 Replies
ADVERTISEMENT
Oct 2, 2012
slow corridor rebuilding after adding superelevation?why?was ok previous years.
Civil 3D 2012
Work: Xeon W3503, 12GB, Quadro 2000, Dell P2211H x 2
Home: 3930k, 12GB, GTX 590, U3011, QX2710
View 9 Replies
View Related
Mar 6, 2012
I am trying to visualize a road project. The problems is, whenever the corridor surface goes below the EG surface (when the road is in cut) the EG surface is the only visible surface.
I sort of need to subtract the corridor surface from the EG surface, or merge the both surfaces into one.
View 3 Replies
View Related
Sep 14, 2012
I have created a surface from a corridor. I set the boundary of the surface to the daylight of the corridor. In some areas of the corridor the surface does not triangulate see attached.
View 2 Replies
View Related
Dec 13, 2012
Copy a corridor successfully? I'd like to try this just a little worried about the explosion of evil this may cause to my Civil 3D session.
Even all the properties of the corridor setup from one to another would be useful. I'm building one corridor and an 2nd one that matches everything except I need to replace my Assembly with one meant for stripping.
View 9 Replies
View Related
Mar 21, 2013
My corridor surface is not matching my corridor top links. see attachments. this is affecting my volumes!
The section-plan(surface red).png is showing the section editor and the plan view. the red highlighted line in section is the corridor surface and as you can see in plan view the surface is incorrect and wiggly.
The pdf is all my sections with the red linework being the corridor surface.
C3D ver 2012
Win 7, 64bit
View 2 Replies
View Related
Jun 25, 2012
the steps of drawing a door hinge. I need to draw sth similar to. dwg file attached. I assume the "Subtract" command was used! what 3D object I should subtract from a shelled-cylinder!
View 6 Replies
View Related
May 5, 2011
Say you have a dynamic block of a hinge, and you want to stretch it to the hight of a door. The dynamically blocked hinges have a base point, and a grip point. I place the base point at the bottom of the door, and stretch from the grip point to the top of the door, (so that there is a hinge on both the top & bottom of the door).
What i want, is for the array tool to automatically place another hinge in the center of the stretch, but only after the top hinge has stretched to/greater than 1000mm. I want this newly added hinge to stay in the center of my two hinges already in place (whenever the hinges are stretched higher or lower, the middle hinge moves to the center), and NOT add anymore hinges, 3 maximum.
View 5 Replies
View Related
Sep 25, 2012
I am assembling a cupboard using a hinge and a door. I can make the hinge swivel quite nicely in its own assembly file. When I add the hinge and the door to the cupboard assembly I cannot get the door to swivel with the hinge. In fact I can not get the hinge to swivel once I place it on the cupboard frame member.
View 3 Replies
View Related
Jun 13, 2013
C3D 2014
when I created a Top surface, C3D showed me otherwise. I need a gap at an intersection. In the attached DWG the intersection corridor has been removed from view by isolate.
I used 2 seperate baselines to force the road corridor to have a gap at the intersection.
Looked OK .. except ..later .. when I created a Top surface, only the first baseline is used to create the surface, the second baseline is skipped : (
I obviously did not make a gap correctly. What is the correct way? Or.. is there no way .. must the designer create multiple seperate corridors when the road has gaps?
View 3 Replies
View Related
Sep 16, 2011
What would be the best way to control the length of this piano hinge in an assembly? I need it to change in length when the door size changes.
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
View 3 Replies
View Related
Jul 24, 2012
How can I bend a Living Hinge at 90deg angles for assembly? Also, is there any tool in either autocad or SW that I can get that final dimension with tolerances? My concern is the hinge might break after printing!
View 0 Replies
View Related
May 2, 2013
I have a very basic question about creating corridors. As you can see on the attachment, i created an assembly consisting of ditch and my own polyline subassembly and turned it into a corridor. The ditch part is drawn out correctly, but the other part (supposed to be a gravel road) has only sections in certain points.
View 4 Replies
View Related
Dec 29, 2013
I started playing around with 3d dwf's. I'd like to share my corridors in a 3d dwf viewer or something similar but when it opens in design review, everything is skewed/ jagged/garbled. The other problem is that it exports everything (assemblies, alignments, sections etc.) so it make viewing navigation difficult in the viewer for people that aren't CAD savvy to begin with. It would be ideal if you could select what you want to export similar to exporting a wmf file.
How do others share 3d models with non-cad people?
View 1 Replies
View Related
Mar 21, 2012
When i try to create a material list, i don't see my corridor surface - just the EG surface appear in the list.
View 2 Replies
View Related
Nov 18, 2013
We are trying to edit a small portion of an existing corridor by adding a generic daylighting subassembly. The add subassembly tool in the Corridor Section editor works, but we get an error because the new sub doesn't have a target surface specified. how to add a target for a sub that is added after the corridor was created?
Civil 3D 2012 & 2013 & 2014
Toshiba Qosmio X505-Q890
2 x i7 - Q740 quad core CPU's
8GB of RAM
60GB SSD + 500GB HDD
NVidia GeForce GTS 360M - driver 8.17.13.0697
Win 7 Home Premium
View 9 Replies
View Related
Feb 7, 2013
When creating an alignment from corridor feature (ditch invert level), the created alignment is not following the selected line (see image bellow). The alignment seams to be created from the first point of the feature line to the last point and ignores all the other points. The vertical alignment created at the same time seams to be correct.
View 1 Replies
View Related
May 16, 2012
I am trying desperately to create a corridor in C3D 2013.
I have the requisite Alignment, Profile and Assembly, yet when I create the corridor, either nothing appears, or it creates the corridor at incorrect elevations. I have the proper elevations in my alignment.
View 7 Replies
View Related
Mar 20, 2012
I had a grading plan all set, with a corridor involved. Then, I received a new survey that I didn't know was coming. I need to move all of my elements to different coordinates. I can move everything except the corridor.
View 2 Replies
View Related
Jun 13, 2012
How to get rid of this gap? Everything I have tried just causes overlaps.
View 1 Replies
View Related
Jan 11, 2013
I only get 2 choices when selecting corridor feature line to create profile - ETW_base, and ETW_sub. My Subassembly has 2 pavement sections, a base and subbase section. I need the top of pavement profile.
View 2 Replies
View Related
Nov 6, 2013
I have a corridor with intersection.The intersection isn't 90 degrees. Can I cut corridor with(for example) 45 degrees?
View 9 Replies
View Related
Nov 22, 2011
I have a block that has a portion that needs to rotate up to 90 degrees. The problem is that it has parallel lines that create a bowtie when rotating. I've tried everything with constraints to get this block to work, but I just can't keep it from creating a bowtie when rotating.
View 7 Replies
View Related
Jul 4, 2013
I've got this hinge working using translational constraints - but I don't seem to be able to apply an angle constrain to it to drive it.
I can't apply an angle constraint when using it as a flexible assembly either - and the flexible assembly keeps throwing an error to do with the translational constraints.
View 5 Replies
View Related
Aug 27, 2013
I want to create a grade (without object grade) using a corridor. This is my assembly:
This only contains the sub assembly "DaylightBench" in the side right.
I have the alignment and profile. I have created the corridor.
red line= alignment
green line= feature line (code Intersecction) converted to polyline.
pink surface= surface (code TOP).
I have added a boundary for surface of type "add from polygon" and I have selected the closed polyline(green line).
However, the boundary seems doesn´t work.
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit
View 5 Replies
View Related
Aug 30, 2013
I am trying yo model river corridor with 4 locks on it. On every locks different between levels is about 2-3m. I it is possible to create profile perependicular to bottom of river. How to create it?
Another question how to later connect surface. I mean Existing ground and corridor intersect. Ho to prepare later for render Existing ground with cutted corridor river? where I am below EG.
View 6 Replies
View Related
Jun 7, 2012
I have sevreal corridors with various spurs. The contractor wants the cut/fill volume in sections along the corridors, not one big cut/fill calc. Is there a way to do this in C3D? I have got the volume table with the chainages on, but he does not want a cumulitive figure for the whole corridor.
View 1 Replies
View Related
Nov 14, 2013
I am creating a corridor with a simple assembly. On my assembly, I have basic lane and daylight Multiple surface. My target is existing ground.
View 9 Replies
View Related
Jul 11, 2013
I am trying to create a surface from a corridor. I have a sub-assembly attached, which I believe is working correctly. I managed to create the empty surface and when I try to add surface data nothing seems to happen. I keep changing the specified code to Base which is my finished gravel structure and hit the + but again nothing seems to happen.
Ultimately I am trying to determine a volume between my corridor and original topo.
View 4 Replies
View Related
Jan 8, 2014
I need to design a project but ı cant..ı have two profiles in use for one alignment..ı want to use left profile for left side, use right profile for right side.and ı want to draw cross section only one..how can ı design like this project..
View 8 Replies
View Related
Oct 17, 2012
I want to add different assemblies (some with walls or ditches) along the same corridor at given stations
Can that be done?
View 4 Replies
View Related
