I have several hundred cross sections for a surface that I need to label the major section breaks. Civil 3D gives the option of weeding based on distance, but I want to label only the major grade breaks (i.e. more than 1%). Is this possible, or is the only option manually labeling the section?
View 2 RepliesI have some cross sections showing existing and finished grade. The finished grade is a channel and floodplain with slopes to catch existing ground. I’d like to create a report of the offset and elevation at each grade break for the finished grade. Optionally, it could be offset and cut or fill at each grade break. I’ve found the tool to create annotation for the offset and elevation info, but the cross sections are too small on the drawings to accommodate all that text. Is there a way to generate a report for the section view group or even each section view that would contain that information?
View 1 Replies View RelatedI created several cross sections for a roadway design utilizing sample lines. I created multiple sample lines along the CL alignment and inserted the cross sections without any errors. The peculiar part is when I try to inquiry or label any cross section, nothing happens. Using the inquiry tool, I get an message that reads "Warning: Specified point is outside the section view. Try Again." If you see the attached PDF, you'll notice that the point I selected is dead center of the particular cross section in question. When I attempt to use labels to mark elevations, in the command line, it repeats "Pick a Point" but does not insert a label.
I created other cross sections in the same fashion and do not have this issue.
I am using Civil3D 2010. I am trying to export the offset/elevation data from my cross sections to a text file or excel file so i can paste the info into another program. so far i've been labeling the offset/elevation info on the section and typing it into excel by hand.
View 9 Replies View Relatedhave a good style to label cross sections at profile grade, top of curb, bottom of curb, grade breaks, and back of walks? Do I set a point or something in my assembly to use to label those points?
View 1 Replies View RelatedHow do you Offset the START CORNER of Cross Sections. I see where you can chose, Bottom Left, Top Left, etc...
I need to move the START CORNER Down and Left. See Attached.
I turned the visibility of Elevation & Offset label off. How do I get it back. Not all just one spot.
View 1 Replies View RelatedCan I offset my alignment labels?
I want to show the alignment staining #'s but I also have a corridor and sample lines running through the stationing that I want to see. I do not wish to drag every alignment label and then have the leader showing.
how to set-up a style what i want to do is label the station and offset of the insertion point of a block by selecting that block and placing the name of the block at the end of the label. as such it would read sta: 14+58.25 - L12.50' P Pole
View 3 Replies View RelatedI just recently was upgraded to C3D 2013 and I am designing my first road using the software. I've been having all sorts of fun and frustrations with Corridors and Cross Sections and learning slowly, but its all the little things that keep bogging me down.
One of the problems I have run into is when I use the Code Set label for Grade/Slope in Cross Sections I get label that reads -2.00% and then the word "Vertical". Is there an easy way to get rid of the word "Vertical" in every one of my 90+ Cross Sections? I checked under Label Style and it seems the only option is {Link Grade} which is what puts the Slope and Vertical. I mean what is the purpose in that word even appearing? I know that I can right click on the label and change visibility to False and it won't show, but I shouldn't have to do that for 90+ Cross Sections. Also I've seen the word "Horizontal" labeled as well and I don't want that word to show either.
I have a drawing that someone else created that has a spot elevation label for a surface. It labels the surface (PAD) then automatically subtracts a set distance for another elevation (GFE) and adds a set distance for another elevation (FFE). After doing some research, it looks like it was created with an expression?
I have two questions:
First, where to go to get a better understadning of this? I'm not familiar with expressions.
Second, where can I find the expression in drawing to make an edit to the set distances. I can remove the GFE/FFE as they are separate components in the label style, but I don't see where to modify the distance it adds or subtracts.
We work with Hydro graphic surveys that have large numbers of points. We would like to be able to display girded spot heights colored to represent the elevation. (Similar to elevation banding)
I have created a surface and then created surface elevation points on a grid with spacing of 15m. I have tried looking at setting up a style that will adjust the color depending on the elevation ie 0 to -1 = red but haven't made any progress.
Attached is a pdf showing the issue I'm having with the way elevations labels appear on the outside edges of cross sections.
Issue #1:
I added the dimension to show that the bottom of the cross section is actually at 97.5 but is labeled as 98
Issue #2:
I would prefer the bottom of the cross section to be at an even elevation (98 not 97.5)
Why not show the labels in sections?
View 2 Replies View RelatedI have a project I designed and grading plan is almost done. My proposed surface lables read as 1256.50. How can I get them to read just 56.50? I have a FG surface I created and am labeling using surface elevations. I am running out of room and need to free up some space. I don't want do drop my surface 1200'.
View 3 Replies View RelatedI am trying to edit labels for a particular alignment. All labels are along the same alignment and use the same alignment style. I need to change "defl." in each of those labels to "defl:". So simply changing the period to a colon. But it is a lot of work to go through each label and then in edit label text and then change it. Plus, I have to do this on 12 sheets. That's like 300 labels! Is there a quick way to achieve this. If it were simple mtext or dtext then I could use the find and replace option, but these are civil 3d alignment station offset labels? Is there a lisp that can accomplish this task? I am using Civil 3D 2010.
View 3 Replies View RelatedIs there a way to remove the extra (In) and (out) invert elevation from my labels? If the IN or OUT (I.E.) is the same there is no need to label them twice. So, can I remove them? If you can remove them, how do you do it?
This is what I have
NEW CATCH BASIN A-11
TOP=427.30
I.E.(IN)=421.60
I.E.(IN)=421.60
I.E.(OUT)=421.60
Is it possible to rotate the point labels when working with point files from an elevation Survey in Ciivil 3D? When activating the labels visibility they are horizontal, but when I rotate the drawing to a side view I am can´t see them.
So far I was working with Autocad (importing a dxf). Is there a way to rotate at the same time all the points labels, wich in this case are just text items?
Trying to change the position of the "elevation" labels on the horizontal axis. They come default as being inside the profile and i want them shown on the outside of the profile box.
View 3 Replies View Relatedi created section view as in pic1. In Bands, Existing surface elevation labels at existing surface grade breaks, top of road elevation labels at top grade breaks, datum is the same. Can i add existing surface elevation labels at top of road grade breaks? (pic2)
View 7 Replies View RelatedHow do I modify the leader for station and offset labels to underline the top line of text?
View 3 Replies View RelatedIs there a way to add elevation labels at any position on a feature line without having to create a surface?
View 9 Replies View RelatedI need an offset lisp routine to offset a selected line a set distance on each side of the selected line and change the layer of the offset lines to the current layer, and then keep prompting me to select the next line for offsetting until I'm finished.
View 3 Replies View RelatedI am trying to create a station-offset label style that will drop the trailing zeros in the offset section - e.g. 15' instead of 15.00', but if the offset is not at a whole number, e.g. 15.01, etc. it will display the entire offset.
I created two expressions: IF(OFFSET-TRUNC(OFFSET)=0,.1/12,.00000001/12)
and this one: IF(OFFSET-TRUNC(OFFSET)!=0,.1/12,.00000001/12)
I then created two offset components, one called truncated, and one called full, and assigned the heights to match the expressions.
I have attached the file, the style is ACHD-Sta Off-Rt [copy]
C3D 2011, Win x64
I am trying to create an elevation label that will give me the spot elevation followed by the letters "TC" and then on the line below subtract 4 inches from the elevation followed by the letters "BC". It's easy enogh to add the letters but the simple equation of elevation - 4 inches eludes me.
View 3 Replies View RelatedWhen I snap a point to an object, the point takes on the elevation of the object. I would rather the point's elevation stay as is.
-changing osnapz variable
-latest civil 3d service pack
A few weeks ago I did not have this problem but once my computer was switched to the company's global server and c3d was reinstalled the problem appeared. Furthermore (post switchover), when a colleage of mine prepared a simple test drawing with just a line and a point, he was able to snap to that line without the point changing elevation. When he sent that drawing to me and I tried snapping the point to the object, the same problem occured with the point taking the elevation of the line object. I suspect it is a system variable issue
i have some existing drainage pipe and structures in a base plan that i need to change the invert (which is the easy part) and the top elevation to the existing top elevation that does not meet the minimum presect in civil 3d 2012 is there a way to change these min. to match my exisitng elevation for example i have a catch basin invert is 15.45 top is 17.56 with a 18" rcp the cover will be less than 12" and i need to change this.
View 3 Replies View RelatedI am trying to create a surface rise:run slope label for our company template file. I have it set using the default values that I want. But right now the text is just 1:1...where we want it to read 1V:1H.
how I can keep the label dynamic to the surface, but put the V & H in the label after the values.?
I think it is normal to want a style showing stationing, speed design stattions, etc.But.... Radii of curves ? Clothoid parameters ?
Why is the reason Autodesk developers think that designers dont want to see this information instead of "add labels, aligments, multiple segments,. etc ....
(aligment by aligment ...... of a whole project ?
Civil 3D (2013)
I am trying to annotate a floor plan to show the location/orientation of section, elevation and detail drawings. The labels must also indicate the appropriate drawing cross reference. (basically a circle with a arrow, text inside circle showing drawing cross reference). My question is - is there an automated way/library to insert such labels or do I have to create each of them from individual elements and make a block?
View 1 Replies View RelatedI am trying to work on a previous file in my office, and when it opens on mycomputer, it does not display as it should.
In general, the purpose of the project is to reinstate the side slopes of a road abutting a river. Cut & fill sections have been generated on 20m station increments along the road corridor/surfaces in order to calulate cut and fill as well as to reference the design to flood levels.
When I open the file, all of these sections (and there are alot) have relocated themselves to various locations in model space, none of which are aligned with the viewports that are being used for printing.
Could it be software and/or hardware incompatibility with the computer they were originally created on? (I believe it was created with C3D 2010, or C3D 2011 - I am currently running 2012)