Is there currently any workaround to bring in alignment descriptions when data short cutting? I have hundreds of lines that are in my drawing that need callouts and this is easily done by making a label with reference text to the alignment description.
View 1 RepliesFor a roadway project I am creating alignment detail sheets. For the first project, only a portion of the final road is being constructed. I have the proposed alignment brought in with data shortcuts and will use various styles for the labeling. But I only need a few different sections of this alignment to be shown. Is there a way I can set clip boundaries or mask out the sections I don't want to show?
View 1 Replies View RelatedI using a data reference/shortcut to properly label an alignment in paperspace. However when I reference the alignment in and apply the labels the aren't the same as the original alignment that I am referencing. Is there a setting where I am supposed to apply a new beginning station.
Also it seems as though the stationing(distance) isn't even matching up 1:1 with the original drawing. For example in the original base drawing my alignment starts at 10+00 with the next PI at 14+76.98, but the stationing on the reference alignment starts at 0+83.33 with the very same PI being labeled as 1+23.08. So the very same distance is 476.98' in the real design and the drawing it's being referenced in, but the stationing of the referenced alignment shows it as 39.75 Units.
I've attached a screen of the beginning of the alignment.
Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU
16GB RAM
I want to be able to repath a data shortcut I have on my drawing to a file thats on my C: drive, how do I do this? Its just for this one drawing I want to do it with, so the Data Shortcuts Editor is no good to me.
View 4 Replies View RelatedHow can I locate the Data Shortcuts Working folder? A surface exist as a data shortcut in a dwg, but the location of the data shortcut folder is unknown and therefore cannot be set in the Prospector.
C3D 2011 (latest updates)
Win 7 Pro, 64-bit
16 GB RAM
I have run into a problem with my Pipe Network data shortcut. When I am in a drawing that is referencing my Pipe Network not all of my structures are showing up. I confirmed this by going to the prospector tab/pipe networks/storm/structures. According to the list It is obvious that not all of my network structures are making it to the new drawing. I've double and triple checked the source drawing to make sure that all the structures actually exist and they do.
I've deleted the data shortcut and recreated it and still nothing.
I was trying to export my alignment, at certain intervals, to excel (or text) as xyz data. I tried searching and found... Alignment to xyz
But it didn't really work. I can export the XY but not the Z in the report manager.
So my questions are.... How can I create a new report to incorporate the Z? Or is there another way to do it?
I should add I also tried the "Incremental Stationing Reporting" from the Profiles Report... However it doesn't recognize the profiles I've created? I get the "No FG profiles in....." even though there are?
For some reason when I try to "Create Reference" to bring in my Alignment, Finished Ground and Existing Ground I get three different alignment data shortcuts instead of them grouping into one. I am trying to find out where in my workflow this all went wrong.
I have a .dwg that just has my alignment files in it. Then I make a new drawing and data shortcut in those alignments and Surface. I make my profiles and then create the data shortcuts for those. I start a New drawing and try to reference the alignment and profile and I get duplicated that aren't grouped. If you take a look at the two .bmp's you can see what happens.
The Purple highlighted area is how I want it to show up and that one worked just fine. Same work flow. The yellow is what is giving me a hard time.
How can i create an Alignment from points (imported) easily without drawing a polyline point to point using a polyline to define a route?
View 1 Replies View Relatedhow to make a data shortcut to a pressure network? Is this feature even available? It seems odd that this feature would be left out of C3D 2013 when it is critical to plan production.
View 1 Replies View RelatedI have a 2011 Civil3D drawing with Data shortcuts in it. I need to replace the source drawing path of the data shortcut with another path. Is there a way to change this either manually or, preferably, programically. At some point we'll need to batch through the drawings and change this path information. Is this information is stored in a drawing dictionary somewhere? If so, where? If not, where?
Updating the .XML data files doesn't appear to affect data links already in the drawing.
I am having an issue with alignments not updating to the latest source drawing. Initially, the alignment source drawing was in File1.dwg. Due to a design change, a few of the alignments were revised in a new File2.dwg. For the first time ever, I used the Data Shortcuts Editor program to repoint the data shortcuts to the new File2 location. By all accounts, it looks like the data shortcut were updated to the new source drawing (File2).
The problem is in some files some of the alignments still source to the File1 location and even when manually synchronizing it still sources from File1. Additionally, it seems random in terms of which alignment and files source to File2, even to the point in some files one alignment will update to File2 and other won't and some alignments will update in some files but not all. Note that I am not the original creator of the files so I don't know much history on the files (no alignments seem promoted however).
What’s the best way for me to get all the alignments to point to the new data shortcut source drawing location?
How do you move a survey database and data shortcuts? Without going into details, sometimes it is necessary to copy portion of projects as new projects. The survey database along with the drawings our surface, points, linework, etc. need to reference the new directory. I can set the survey database folder location to the new path but am not certain the information in the dwg is point to the correct location.
The same essentially applies to the data shortcuts. I'm having trouble getting this to work. With LD we were able to copy the project and resuscitate the drawing(s). I tried to use Data Shortcut Editor with the Saveas. I then attempted to rename the dwg's and path the new location and name but receive an error of Invalid source file. Correct the path or press Esc..
Is it possible to data shortcut a surface from c3d2013 into c3d2012?
I tryed it and it says that the surface is in the drawing but its not showing up.
I've tried changing the style and the layer but nothing works.
is it possible to lock an alignment to a pipe network, so that if you move a structure, the alignment moves with it?
along those same lines, when you create an alignment from a pipe network, is it possible to auto assign the reference alignment to the pipe parts, so that labels come out correctly?
Is there a way to have a block (called test, for arguments sake) within this block we have text (attribute / fiield or whatever).
Now I have an alignment that has stations set every 10 units and on those stations I have inserted the block "test" as part of the alignment label style.
I can get the block inserting correctly, rotation the direction I require etc but what I need is for this block to report the station number.. ie 10, for the first 20 for the second and so on.
Is this possible?
I have an alignment I need to edit that has a reverse curve. The first curve was made with the "Floating Curve (from entity, radius, through point)" and the second with "Free Curve Fillet (between two entities, radius)"
When I delete one or both curves i lose all the superelevation data beyond the editing location due to the temporary spit in the alignment. The superelevation data is all manual. This is a trail and the super is based on drainage not curves.
how to edit the alignment with a temporary split and not lose the superelevation data? I have not found a way yet to remove the reverse curves and not have a temporary gap.
In LDT listing curve data was as easy as selecting an alignment, clicking edit and printing out a spreadsheet with all the required info. how to do this in C3D. Inifo I need:
Delta
DOC
Tan
Length
Radius
PC
PT
PI
Is there a way to export the band data for an alignment with two profiles? I have an existing ground and a proposed profile. Can I export the station and elevation data from the band for both profiles?
View 9 Replies View RelatedOccasionally I get the following message when trying to add data shortcuts.
"The drawing has not been saved yet, please save the drawing before creating data shortcuts" Only I have saved, this still occurs after either a full or quick save.
Shutdown Civil and reopen still gives the same message..The problem seems to be when you are saving to any other version of Autocad than R2010. Save as R2010 and it works.Mike Evans
Civil3D 2013 / 2014 British UK
Windows 7 Professional 64-bit
Intel(R) Core(TM) i7-3820 CPU @ 3.60GHz (8 CPUs), ~4.0GHz With 32768MB RAM, AMD FirePro V4900, Dedicated Memory: 984 MB, Shared Memory: 814 MB
I'm trying to find out what could be the cause of sturcture styles in a Pipe Network Design Drawing resetting to default styles when I Data Shortcut the design into my Sheet? (I.e. I've got gate valves, fh's, and plugs in my design file, but when I data shortcut them into my sheet they are all come in as null structures) Not Cool!
I'm using the same template that contains all the same parts/styles for both design and sheet.
I have a data shortcut file where i keep my EG surface that now has File Name.dwg [DS] [DS] [DS] [DS]. What's the deal? Has this managed to morph itself into something it's not. It used to have only one, had two for awhile, and now 4 references to the DS (Datashort cut project folder).
Have I done something wrong here to get these wonky file names, would be nice to see just 1 reference being made to my DS Project folder.
I made a pipe network in one drawing, d-reffed it to another, drew parts in profile.
Then I realised that I needed to show the outside walls of some pipes in profile. We don't normally display them. And I found that the wall thickness was wrong. I eventually figured out how to edit the wall thickness, and I have it working right in the source drawing. (I had to swap parts to get it to update.) But the host drawing is not updating.
So if I go to pipe properties in the source drawing, it gives a wall thickness of 165mm (correct). If I go to the same pipe in the host drawing, and go the the pipe properties, the wall thickness is 75mm (wrong).
how to trigger an update? I've swapped parts back and forth to different sizes, synchronized, SetNetworkCatalog and done PartCatalogRegen in both drawings.
For background, read Edit wall thickness.
Civil 3D 2011, 32 bit
Win 7 Pro, 32 bit; Intel Core i5 @ 2.80GHz; 4GB RAM
I need to produce a better standard table for our company, but need to know how it would be possible to display only either the START STAKE VALUE/ STATION or END STAKE VALUE/STATION in the appropriate column. If I can achieve this i would not need to details for straight segments as indicated in the details column.
View 5 Replies View RelatedI am working on roadway project where I am using Pipe Networks to layout the drainage infrastructure. I have set my working dwg up so that I am data referencing the existing surface and proposed alignment. I have set my pipe network up so that it is also referencing this surface and alignment. Everything was working fine. Labels were pulling the correct information from my surface elevations, and stations were being referenced as well, until I got a message that recommended that I recover my drawing.
I ran recover and my surface and alignment data shortcut disappeared. My pipe network now shows questions marks where there were once stationing and it appears that the surface and alignment have completely disassociated themselves from my drawing, however they appear in the prospector, but cannot be refreshed. Again the data shortcut symbol is no longer next to my surface and alignment, but there is a symbol telling me that those objects are being referenced by another object in my drawing (my pipe network). I have tried refreshing, resetting the working folder, all to no avail.
I have been provided with Surveyed Utility Locates along an Existing Roadway. These are provided to show conflicts between the New Storm Sewer System and Existing Utilities such as Water, Sewer, Gas, Elec, etc. The survey however is incomplete as it was prepared a few years ago and the Storm Sewer has just been designed. Yes, I can create points and provide them to the County Surveying department. However, before this is done, I must provide an easily-understood format of the new survey locations to the County Project Management.
To provide a Point Table which references the Surveyed Points' location in reference to the roadway stationing (Alignment). I have attached what the point table is to look like.
I am unable to find the desired data reference in the currently provided data field selection. Am I just missing it or is this a "Wish List" item?
is it possible to get the alignment name which the corridor surface is built from when the surface is being data referenced. in other word no corridor as the middleman.
the way i see it is when corridor suface is referenced, it becomes a regular surface and loses some properties such as parent alignment.
i am still using COM. maybe .net can do it? either way works.
Civil 3D 2012
Work: Xeon W3503, 12GB, Quadro 2000, Dell P2211H x 2
Home: 3930k, 12GB, GTX 590, U3011, QX2710
I've got a drawing that has a data referenced pipe network (C3D2014). Everytime the pipe network is syncronized the pipes and structures change their styles back to what I can only assume to be their default. I can not find where to change this style or behavior.
View 9 Replies View RelatedI have a existing ground surface drefed into a model and am trying to get a user defined contour at a set elevation but nothing appears. I have userdefined layer on in the surface style and other ideas why it will not appear?
[URL] ......
Using C3d 2013.
Where do I find the PI data of an alignment object to plug into a mtext Field?
Field Category and Field Name and any other steps to locating it would be useful.
I have a sheet that has several alignments data referenced and labels applied. Recently some of the alignments changed (slightly extended), I checked the sheet and all of the labels have auto updated. Everything looks good. A Print Preview looks good.
When create the print (to pdf), the alignments that changed and all the labels do not show up. Nothing changed with layers, styles, etc. I tried Synchronize and Refresh from Prospector. I can create another Data Ref but don't want to go thru all the labeling again.
Preview and pdf attached.
C3D 2012
C3D 2012 sp1
W7Pro 64bit
HP Z400 Workstation
16 GB RAM
Intel Xeon CPU W3565@3.20GHz
NVIDIA Quadro 4000