I have a complex intersection of three corridors with:
- oblique angles
- different sections assemblies (one way and two ways - full section)
How should be the best approach to solve it?
I have 2 roads crossing, and I have created the 2 corridors, and an intersection object created. I split the 2 corridor regions and put the intersection in, and then closed back in the regions to the start of the intersection object (region). Now - how do I make that all one corridor object that reacts to either of my profiles, and is only one corridor surface? - the corridor surface ignores my region boundaries Or at least 3 objects that interact with each other properly. Image 1 highlights the start/end of the corridor regions, and image 2 shows how the surfaces look - why doesn't the corridor surface start and end where the regions do?
View 3 Replies View RelatedI am using corridors to model a driving course. I have attached two images that show 2 scenarios. One is where an alignment loops back onto itself. The other is similar to a merging lane.
What are the best ways to handle these? I am having a hard time with the surfaces overlapping. I have tried using targets, but they don't work well.
I have a site access road that extends from highway into site and then loops around and intersects with itself. Would like to keep this as one alignment in order to make Super Elev and master alignment easy to control across project team.
Issue is, we would like to use Intersection wizard at the intersection but cannot, as we ony have one alignment. We could model the intersection the old way, using kerb returns with design profiles, but as the design is still in early stages the intersection is likely to be frequently revised.
how we could utilise intersection wizard in this scenario?
I have 5 intersections in a drawing and i try to update all the intersections regions one after the other with "Update Regions and Rebuild Corridor". The problem is that sending up to date some intersections send other intersections (previously updated) out of date. So i cannot have all my intersections updated. The only way i found to correct this is to "Update regions automatically". but this way i cannot make changes to regions manually.
View 3 Replies View RelatedI'm not having any luck on my own. Can I use subassemblies that I create in subassembly composer to make an intersection using the "CreateIntersection" command?
View 5 Replies View RelatedI've read that it is possible to "hand draft" small complex areas that a corridor cannot handle easily.
I have an intersection in an old neighborhood that is constrained by retaining walls, buildings, and so on. In this I have to fit in current ADA ramps. Due to constrained space I will have to get creative in my elevations and layouts.I'd like to somehow integrate it with the corridor.
Windows 7-64
8GB RAM
AutoCAD Civil 3D 2013
I am using C3D 2013.
Is it possible to edit a sub-assembly in the Corridor Modeling Catalog (Imperial.NET) see attached image.
The company I work for has several users working off one network server. I would like to make a revision to one of the dimensions in the sub-assembly "UrbanCurbGutterGeneral" (the default gutter width is 16" I would like to make the default 18"). I'm assuming I need to change this in the Catalog so every users tool palette will be updated also.
I am trying to create an intersection design using the Intersection Tools in C3D 2012. I followed the steps in the tutorials, created a corridor on the major road, splitted the regions, created the intersection and added it to the major road corridor, and connect the regions with the intersection portion.
I used the same assembly throughout the design just for simplicity, however, i notice that there are gaps of curb between the curb return section and the through section (as outline in red rectangles).
I have created a surface from a corridor. I set the boundary of the surface to the daylight of the corridor. In some areas of the corridor the surface does not triangulate see attached.
View 2 Replies View RelatedCopy a corridor successfully? I'd like to try this just a little worried about the explosion of evil this may cause to my Civil 3D session.
Even all the properties of the corridor setup from one to another would be useful. I'm building one corridor and an 2nd one that matches everything except I need to replace my Assembly with one meant for stripping.
My corridor surface is not matching my corridor top links. see attachments. this is affecting my volumes!
The section-plan(surface red).png is showing the section editor and the plan view. the red highlighted line in section is the corridor surface and as you can see in plan view the surface is incorrect and wiggly.
The pdf is all my sections with the red linework being the corridor surface.
C3D ver 2012
Win 7, 64bit
I'm a beginner/intermediate level 3ds max user and I've recently starting to model what I love the most - sci-fi stuff, more specifically, space ships. So, I've been browsing the net looking for models done..Now, there's one very specific question in mind: does a ship (say, a very creative and complex concept) has to be one single object, or can it be a group of linked objects? Notice that I have in mind game development. URL....
View 9 Replies View RelatedI have a topo map in max, and I'm trying to raise and sink parts of it to make sidewalks and parking lots. My thought was to import line objects from dwg files, shape merge them onto the terrain, change the material number, then extrude. The problem is that shape merge doesn't maintain the correct shape.
I've made sure that I'm in orthographic mode, looking straight down on the surface, but anywhere there's a curve it messes things up. Circles become irregular ellipses. Arcs become more convex or concave. Where I'm shape merging two different objects at different times, objects that had lined up, the curves are now different and they either overlap or no longer touch.
I'm assuming that it's because my terrain mesh is too complex, but I'm not sure how to get around that.
Are ther good sources available for learning about modeling curtain walls- complex curtain walls in Revit?
View 1 Replies View RelatedTypically a door hadle lever comprising initially circular geometry at the rose (fixing point) with round bar (x place)geometry up to and around the initial lever bend. Then the lever elongates in section and curves along a y plane and possible twists along its sweep path. Ive tried mass and create solid using a path with worlplane aligned geometry with fail every time, Also tried in face based generic. The problem is a bit abstract in that only trying to take an image in a manufacturers catalog of a manufactured component and recreate the design phase. Can this be done (sucessfully) simply. If only there were a way to do a swept bleand withj sveral profiles on the path. Hosting circles and then curved profiles is not working for me - cant get uniformity in the way the circles sweep into the curved parts
View 6 Replies View RelatedWhat distinction is between “intersection” and “apparent intersection” in snaps,. I’m not sure what difference is between the “intersection” and “apparent intersection” in snaps.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I am tring to grade a complex object. Please see the attached document. The two grading objects are not interfacing correctly when graded although i can get the surface almost correct i beleive. Is there a way to remove this issue or the grading will not create a lot of difference when computing the volume clacs ( we are talking volum computation roughly about a million cubic metres cutting).
View 4 Replies View RelatedI've started doing my first intersections but I'm stuck with one mistake. I did all daylights and curb returns for intersection.
I have a feeling that it's incorrect targeting here, isn't?
What is the best way to relocate and intersection (created with the wizard) from 43+00 to 40+50? I dragged the alignment but the return baselines don't seem to come along for the ride. Would it be better to bite the bullet and redo it?
View 3 Replies View RelatedI am "trying" to design a intersection that contains four lane divided road. Northbound and Southbound lanes are 2% normal crown with a curbed median. I have alignments for each crown. The intersecting road is not crowned. This road is a retrofit so I am limited quite a bit so the intersection wizard is out. We're going old school with this one.
View 2 Replies View RelatedI need a style for intersection of alignments that automatically includes the abbreviations for Point On Tangent (POT), Point On Curve (POC), etc. I can create a style with the basic information of Station, Alignment Name, but adding the POT, POST, etc. in front of all alignment’s stationing and name doesn't seem available still in Civil 3D 2011.
View 9 Replies View RelatedI m trying to create an intersection between two roads. See the attached jpeg. When i open the corridor properties i receive an error message which i don't understand. It seems like civil 3d has problem with the order of the regions. Also the corridor sections intersects in the area that i have place a remark "problem". I m trying to correct it manual but when i rebuilt intersection then it overlaps my manual correction
View 3 Replies View Relatedissue with my Corridor. It involves the intersection of a main road alignment and a secondary road. Thing is my main road has a 6' shoulder whereas my secondary road doesn't have a shoulder at all. I used the Intersection Wizard to create the Intersection, but the two templates don't align. Without the shoulder the ditches don't line up. I tried drawing a polyline between the two ditches and targeting it and that worked, but then realized that going from 6' shoulder to no shoulder wasn't working either so when I tried to target a polyline from the 6' shoulder to the edge of pavement all kind of stuff happened that didn't make sense to me.
Windows 7 Prof w/ SP1, 64bit, Xeon 3Ghz, 16GB
Civil 3D 2013
I have a link starting from P1.Is there a way to check if the link is intersecting EG or not?
Civil 3D 2014 x64
Windows 7 64-bit
16GB RAM
C3D 2010 user
I have a problem modeling intersection. This is first time I am modeling intersection. I have gone thru' and actually did all intersection tutorials offered by C3D and naturally I felt like I am ready for it.
But in real world I am not. I am trying to model intersection and I keep getting error as "Value on Wrong side of alignment to profile". I looked at target mapping and thinks so that all is okay (may be not). I am attaching snapshot of error message as well as plan view. I wanted to forward actual dwg but size is too large to post.
Point to note:This is Left lane driving setting. I realized this after I created alignment/profile/assemblies but before I tried intersection modeling.
I did 8 iterations before this post.
I would like to know how it would be possible to manipulate the Intersection Wizard so that I can obtain the required shape as drawn by the architect. In essence create a "round about" shape. see the attached image for furhter detail.
View 4 Replies View RelatedMy corridor surface randomly bounces from top links to bottom links through the intersections even though I specified top links only and my corridor is modelling correctly.
Previously I just deleted the surface and recreated it with no errors but it doesn't seem to work now. This happens with both manually created intersections and ones created with the intersection tool.
Creating an intersection of two roads. I have created corridor using alignments, profiles and assemblies. then i have created the intersection. However, i find it quite strange. Maybe it's because of the assemblies. . I am attaching the file herewith .
View 1 Replies View RelatedI have a super-e road assembly as shown that is running into the intersection of a future road stub. I can not figure out how to get the sidewalk to grade out in the intersection transition I have created for the curb return. Any way to get through this situation?
View 2 Replies View RelatedI have a mainline corridor which is intersecting with a side road corridor that is curving towards the mainline. After the PT of the curve, the two alignments are parallel and I am using an offset assembly here for the sections. What is the best way to handle the area where the two corridors are coming together. As far as I've been able to tell, I cannot use an offset assembly through the curve. There will be a ditch between the two that needs to be shown someway or another. I've attached a screen shot.
View 5 Replies View Related