In Regis you copuld use the "clean"command to break each line at an intersection. What command or function must I use in AutoCad 2013? I wish to break the lines at each intersection in order to import the lines into a GIS application. I am currently drawing in 2D.
View 4 Replies
how to break a line or polyline down to equal segments.
View 4 Replies View RelatedWhat distinction is between “intersection” and “apparent intersection” in snaps,. I’m not sure what difference is between the “intersection” and “apparent intersection” in snaps.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I have some sections and am using the break line with a masked region but in Revit 2013 the masked region only works in the Wireframe Graphics display option. It does not work in the Hidden Line display. It was fine in 2012
View 7 Replies View RelatedI have feature line with elevations that represents bottom of ditch and want to go UP 3:1 slope. also i have edge of road feature line that is higher than ditch and want to go 2% down until it hits side of the ditch that is 3:1. Any easiest way in civil 3d to create intersection line between ditch bottom going up 3:1 and edge of road going down 2%?
View 2 Replies View RelatedI needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?
I have an FDO layer which I am styling like so:
Concat ( FDO_LAYER1, Concat ( '
', FDO_LAYER2 ) )
This layer is styled so that all text is centered. In this case, FDO_LAYER2 is having it's text left aligned. I'm pretty sure this is due to the method I am using for a new line. Is there something else I can use to break the line and maintain the center styling?
Using a second point for FDO_LAYER2 is not an option.
I draw a curved line and would like it to remain as a curved line even after saving the file. However everytime after saving, and opening the file again, the curve breaks into many line segments, which is not what I want! I want the curved line that I draw to remain as a curved line even after saving and opening. How do I do that? I am using autocad2010.
I use the ARC command to draw a couple of lines, they look okay here. But after I saved it, and re-open it again, what previously appeared as curved lines changed in their appearance to polyline segments.
how to break diameter line into horizontal line at the end ?... there's no such option in editor style (I want to have 2 arrows for this diameter, not one as it is in editor options)
View 2 Replies View RelatedHow do we do a break and or jog line in a section so we make things shorter? I did find the DIMJOGLINE command and that will be great for the dimensions but what about the other stuff, do we have to do that with a block or draw the thing, if that's the case what are you doing to handle this?
View 5 Replies View RelatedI'm trying to get the "Y" intersection of a line I construct and a given polyline using the following code.The debugger stops at this line that calls the function
intersectStartY = GetYIntersection(elevationLine.StartPoint)
The error message is "MissingMethodException was unhandled by user code"
Method not found: 'Void Autodesk.AutoCAD.DatabaseServices.Entity.IntersectWith(Autodesk.AutoCAD.DatabaseServices.Entity, Autodesk.AutoCAD.DatabaseServices.Intersect, Autodesk.AutoCAD.Geometry.Point3dCollection, Int32, Int32)'.
{code}
Public Function GetYIntersection(ByVal elevationLinePoint As Point3d) As Double
Dim intersectY As Double = Nothing
Dim intersectPoints As Point3dCollection = Nothing
[code].....
I have a drawing file in AutoCADMap 3D 2011 consists of some administrative boundaries and city boundaries. Now I have roads of multi line style in the same drawing. When I completed the drawing I noticed there were missing intersections and I wanted all the roads to look something like the drawing shown below.
Please look into the word file thats how I wanted to do intersection in my drawing. Is it possible to do this action in one command or tool.
This is how my drawing looks like. This is how I want the drawing to be.
When trying to place a construction line through an intersection the line offsets depending on where the cursor is placed. When the on screen prompt ask to specify through point. It defaults to 0 and I enter in 45'. It comes back invalid. believe this is a snap setting somewhere but I cant seem to find it.
View 2 Replies View RelatedI have to break a line/polyline with a known distance around a point of the line. I was thinking of creating a circle with a specific radius and then trim the line inside the circle, then delete the circle but I could not find how to use trim in .net.
View 1 Replies View RelatedHow can I break a line without leaving a gap?
View 4 Replies View RelatedI know we can do this easily in AutoCAD Electrical, but I could not find any command or feature in AutoCAD to set up this function so that when two lines are intersected, the cross point will become a dot or loop.
View 9 Replies View RelatedIs there a command to break a line or dimension, to show that not all of the line is displayed or where the length is not important or undefined?
View 4 Replies View RelatedWould like to know if Autocad has any thing that i could use to break multiple line at one time with out going to each line and using the break command. Using Autocad 13.
View 3 Replies View RelatedIs there a way to set up autocad(2004) so that when I insert a block, the block then automatically breaks the line I am inserting it on. My drawing's are mostly electrical schematics so the line I am refering to is the circuit and my blocks are components. At the moment I insert my block and I have to use the command 'break'. I know this does not take up a lot of time but I am always looking for ways to speed up!
View 8 Replies View RelatedI would like to ask a question on “Break at point”.
It is possible to break a line but for circles and ellipses, my attempts resulted in no break at all (see attached picture).
Does “Break at point” support circles and ellipses? If you have a circle and you would like to make it a ¾ circle arc, or any arbitrary angle, how do you do that?
brk.png
How do you add a break line for stairs? In windows it is under 'express tools' but I can't find it in the mac version.
View 1 Replies View RelatedIs it possible to select lines (maybe up to 6 lines) around an intersection point with a reference line. There is one intersection point and the lines are around it. And also, both the intersecting lines are in different layers.
How to get the ObjectARX's ArxDbg tool working on autocad 2012. ObjectARX 2010 sample project fails to open in VS2010 express.
I was looking for a post on the subject of line and circle intersections and found one that Bill Z had posted. I decided to incorperate one of the replies into my own code. In particular Luis Esquivel's code. With some minor modifications I was able to add the onseg argument that extends intersection points for the line to the circle. I also modified it to return only one point or two points depending on the line and circle supplied and the onseg argument. It seems to work great.
; test function
(defun c:go ( / )
(ed_init)
(while
(or
(not (setq ent (entsel "
[code].....
I often use feature lines for parking lots and ponds. They're great when they work, but they drive me NUTS when they don't - which is a lot of the time. For parking lots and ponds, my feature lines usually close back on themselves. That's when I have trouble breaking the feature line. When I use BREAKFEATURE, I choose two points and this should, in theory, leave a gap in the feature line between those two points. That's not what happens. I end up with a huge gap between the first point I picked and a vertex point 5 or 6 vertices away. It doesn't matter where I pick the breaking points.
I've also tried TRIMFEATURES. I draw lines across the feature line where I would have chosen the breaking points. But the portion that I want to remove is the portion that always remains. It doesn't matter where I select the feature line to be trimmed (inside or outside of the cutting edges).
I think there may something wrong with the feature line itself. Sometimes, if I erase the original and draw a new one, it will trim just fine. But that's such a headache, and it doesn't always work. If I knew what was causing the feature lines to go squirrely, I would aviod it. Unfortunately, it seems like breathing the wrong way can screw up a feature line.
How can I use one "line break" in the same command on iLogic ?
For a simple doubt, a simple sample :
MessageBox.Show("Message blabla blablablabla blablablabla", "Title")
In this case, how could i divide the message in 3 lines in the messagebox ?
actually this would work for me in other case too, creating a text with more than one line, instead of creat many text boxes.
IV 2013
Want to break/cut a line which is in reference file.
I know MicroStation has this function called "mask". Does AutoCAD has similar?
I want to break a line into thirds or fourths.
View 5 Replies View RelatedHow do you detect the intersection of a line and circle or arc.
View 1 Replies View RelatedI have to create a hole (extrude) in a wall part in my assembly document where a stack will be installed.
To determine where, I verify if a line segment pass through the wall (XY Plane).
But I get an error with the command: IntersectWithLine
Here's my
Public Function IntersectionPoint(ByVal app As Inventor.Application,
ByVal wp As Inventor.WorkPlane) As Inventor.Point
Dim oTransGeom As Inventor.TransientGeometry = app.TransientGeometry
Dim startPoint As Inventor.Point = oTransGeom.CreatePoint(Me.StartVertex.X,
[Code] ......
What controls the line weight of the break lines in the detail views? Have tried everything, but still have them shown very thick.
View 2 Replies View RelatedIs there a way to have a multiline point description? For example, in the raw description, i wrote out the text, but I would like to return a line for the parentheses.
Civil 3D 2013
Windows 7 64-bit
Inteel 2.40 GHz 8 GB RAM
Dell T7600
