I am trying to dimension a line that is not parallel to either they x or y axis. When i try to demsion the line it will only let me dimension the vertical or horizonal component and not the diagonal length. I have included a picture of what I am reffering to.
View 2 RepliesI am trying to dimension a line that is not parallel to either they x or y axis. When i try to dimension the line it will only let me dimension the vertical or horizontal component and not the diagonal length. I have included a picture of what I am referring to.
View 5 Replies View RelatedIs it possible to override a dimension with some sort of formula or function that relates to the length of the dimension?
A simple linear scaling might be possible by inventing a new unit with the appropriate conversion ratio, but that wouldn't work. What I need for the dimension to display a length 400 less than the actual length.
Can i change the length of the dimension line 'extension' when my dimension text placement is beside the dimension line (see attached image)?dim line length.jpg
View 6 Replies View RelatedI would like to dimension the arc length of a radius in sketch mode. I am using Inventor simulation 2010.
View 4 Replies View RelatedIn Autocad 2006, is there a way to control the length of the dimension line when it extends outside of the dimension distance itself? In other words, when a dimension is small, and the arrowheads flip to the outside of the dimension parameter, the text and the extension line outside of the dimension seems to go to far outside of the dimension area..
Can I control how far outside of the dimension area that this line and text are placed? They seem to go to far out on my drawings. I prefer them to be closer to the actual dimension area instead of extending so far out.. Didn't know if there was a control for this and where to find it.
I have to flip out dimension lines/arrows all the time. How do I control the length of the dimension line when it is outside two lines?
View 1 Replies View RelatedIs there a way to show the last number of the dimension length as 5 or 0?I want to show the unit in mm with precision (decimal places) equal zero such that the and to force the last number as 5 or zero
For example, I need to display the 7554 mm as 7555 and the 7558mm as 7560.
Is there a way to add a specific amount/length to a dimension by using a formula? For example, say I wanted to measure a length of conduit between two fittings. The clear distance between the fittings is 48" and the conduit is recessed into the fittings by 3/4" on each side. If I dimension between the fittings, normally it would read 48", but I want it to read 49-1/2" so my shop people know what length to cut.
View 9 Replies View RelatedA plotting issue that has never been addressed perplexes me! When working in a paperspace layout and trying to plot or print by window or display, I get a partial print or nothing at all. Typically, I will get a partial print showing the drawing above a diagonal line. This has plagued me through many versions of Autocad.
View 4 Replies View RelatedI put a dimension in paper space to check the length of a line and after, i wanted to clear that dimension but it didn't dissapear. If I zoom out or zoom in the screen,the dimension still remains in the same place and it's not scalling. What can I do to clear that dimension?
View 9 Replies View RelatedSome times when I re open a drawing I have been working on, I start to dimension and I notice that the dimension extension lines stay the same length when I move the dimension in and out from the object being dimensioned.
Not sure why this happens, I do all my dimensions in model space, in fact I do just about everything in model and then just set it up in paper space to print.
I never change anything when I start a new drawing in my template, so not sure why it happens.
I'm trying to use the new arc length dimension feature in Inventor 2013 and I am having some trouble. After I apply a driven arc length dimension to a fully constrained sketch and then put user dimension in a user parameter I get an error when I rebuild the part. The error states the the dimension can not be solved.
View 9 Replies View RelatedHP Designjet T520 36 inch ePrinter (CQ893A)
Latest HP-Driver: 61.125.1522.100
Latest Firmware: AXP2CN1325AR
Windows 7 64-Bit with AutoCAD MEP 2013 + 2014
we get rasterized diagonal lines when printing from AutoCAD on that Printer in A0 format, straight lines are ok.
Printing FIRST to an PDF printer an THEN to the T520 ist also ok (this is what the customer currently does and the quality is good). Got some suggestions from a local ACAD dealer (max. details in the printer driver) but no success ...
My goal is to be able to select a line and a dimension and then have the line's length appear as the text override for the dimension. I have the code to substitute the variable "dist" for the dimension text:
(setq dimselected (entsel "
Select Dimension:"))
(setq newlength dist)
(command "dimedit" "n" newlength dimselected "")
but am having problems extracting the line's length to the variable and setting setting it equal to the variable. To make things more interesting, the value needs to be in inches with fractional inches accurate to 1/16".
it's been awhile since I have been back to autocad. I draw a line an exact length then when I try to dimension it with a fraction it rounds up. I can't find the setting. It is say 5 1/2" but will dimension to 6"..
View 7 Replies View RelatedIs there a way to adjust the length of the tick marks used in dimension strings? I'd like something other than the supplied Diagonal 1/8" or Diagonal 3/64" options.
View 1 Replies View RelatedI have used AutoCad for a few years and I installed 2013 to my laptop recently.I noticed that I couldn't specify how long a line should be. When I select the line tool and specify the base point and type how long it should be i.e. 3' and a red box appears around the dimension box and the line isn't drawn. I tried not specifying a unit of length and it draws the line just fine. But for some reason it wont complete the line if I specify feet or inches.
View 2 Replies View RelatedCurrently when I pick a grip at the end of a polygon line and type a length, the polygon goes to that length.
Is there a setting anywhere that changes this behavior to add the typed length to the polygon, hence stretching it to this new length. This would be the same as lengthen when drawing with lines.
In previous versions of autocad after I select a line, and put the mouse pointer over a vertex, there would be an on screen number displaying the length of the line. In Autocad 2013 this seems to have disappeared. how to get it back?
View 2 Replies View RelatedI have a drawing and I have a field calling up the path and file name. Is their a way to limit the size of the path displayed? For example, if my drawing is C:users
ame1
ame2
ame3 4
ew5.dwg, is their a way to only show ...
ame3 4
ew5.dwg?
Is there any easy way to get the total length of selected lines (even if they are not "connected") ?
View 6 Replies View RelatedHow can I take and display the lenght and the radius of all elements in my DWG.
View 3 Replies View Related The cells of the table don’t respond to the chosen height/length
1.I’m wondering why the cells of the table don’t respond as a particular value is typed for them.
2.Also, If all cells are selected to be given a particular height/width then they don’t respond as well.
3.Originally, the inserted table doesn’t respect the value of width assigned for it!
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Is it possible to change the length of a line based on the length of an attribute?
I'd like to make the line a MINIMUM length of X" (I haven't decided how long yet--but know I'll need a minimum). But then after the user fills in the attribute, I'd like the length of the line to change to the length of the attribute plus a small amount (again, I haven't decided yet how much extra).
I was wondering if there is a way with DB's to have a line "follow" or "grow" with the content/value length of an attribute. Maybe some method of linking the attribute width to length of the line? Essentially, it would work just like turning on the underline setting when typing in mtext editor (or any program with an underline option for that matter), expect that the line could be placed anywhere, and would not have to reside directly below the text.
View 5 Replies View RelatedCommand to make a line change length to match length of a line, arc, polyline or circle? Could use this when making flat patterns layouts.
View 5 Replies View RelatedWith using superelevation wizard in Civil 3d 2012, changing the lane width is not affecting the resulted values of transion length and run-off length, Is that correct ? ( as civil is using standerd AASHTO tables which assume that lane width typically is 3.6m )
Also, There is only 2 tables for 2-lanes and 4-lanes roadway, Is it for total road width or for one directon only, and what about different no. of lanes ?
I am creating a block with attributes for a standard job. I have (4) total attributes in this block (for example: panel type, qty, length in imperial, length in mertic)
I would like my length in metric attribute to automatically populate based on the input from length in imperial.
Is this possible?
when I draw a shape and add a dimension to it, the text and the numerical and the arrows of the dimension are small, so I have to increase the text height manually
how can I make it automatically scale itself?
also similiar thing with the lines, I tried putting a dashed center line on a shape, it looks solid but when I zoom it it does not.
how can I solve this?
Exclamation mark with the dimension!
I’m wondering why I got exclamation mark (!) with the dimensions! I wanted to get rid of them but sounds that there is now way to achieve that. I tried to right click the exclamation mark (!) and choose the “reassociate” but with no effect!
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.