When I open a large facility building drawing my mouse is "jumping" on the screen.
The resolution of the mouse does not allow me to select obejects on the screen because the mouse jumps in large increments.
I do not have this problem on smaller drawing, such as electrical schematics.
Is there a setting to increase the resolution of the mouse movemrnt id AutoCAD?
ouse has started jumping across the drawing screen. snap is off
View 1 Replies View RelatedThe screen flickers when I move the mouse around an open drawing. I just applied the latest patch to Civil 3D 2010. It was not doing this before the patch.
Have Quadro 3500 video card. Updated the driver for that with no change.
Have a Logitech wireless mouse, M310. Up dated the driver for that with effect.
Changed to a wired mouse, no change.
Is there a setting in Autocad where I can set the refresh rate so that it does not refresh while moving the mouse. Or at least slow the automatic refresh rate down?
I'm here with 2013 SP2 64 bit Build 200 and two screens. Left screen is graphics area, Browser is on the left of right screen. Graphics is ATI Fire Pro V7800 with driver 9.3.3.3000.
In video (zipped MP4) you see a cutout of both screens, think of screens changing at the left of the browser.
Now, in many cases, after doing an operation, the browser is jumping back to the middle of my graphics in the left screen.
I have an autocad drawing that has a building floor plan.
I need to "rotate the building 90 degrees" or "rotate the USC 90 degrees" in order to line the building up to TRUE project north (architect has a Revit model oriented to true north that I need to match when we combine our files in Navisworks)
I have tried DVIEW > Twist.. which I thought was it, it rotated my drawing, but the USC rotated with it. I tried the USCFOLLOW with no luck.
Also tried going into UNITS > DIRECTION and tried VP with no luck.
I understand that I can just select the entire floor plan and manually rotate it BUT, the building is not easy "shape" to work with, so it is next to impossible finding the "center" of my drawing to rotate it (I need this to be brough into Navisworks WITHOUT rotating the file again)
You would think this would be very simple to do and take 30 seconds. I have googled everything with no luck. I just need to change my True north
- doing this in modelspace
- needs to be align with a Revit model already oreinted to true north
- just need to rotate the drawing OR UCS 90 degrees, but can't find the "center" of the drawing
Is there anyway to prevent a corridor from jumping across large distances as in the attached screen shot? There are no targets in any of these regions.
View 1 Replies View RelatedSince installing Illustrator CS6 I am finding that my mouse jumps around the screen erratically while trying to draw making it almost impossible to use the program. It is particularly bad when I connect to a projector for training purposes. This doesn't happen with any previous version of Illustrator (or any other program for that matter). I know it isn't something as simple as my mouse because I tried several different ones but to no avail.
I am using Illustrator CS6 for Windows on Windows 7 and my problem is mainly on my laptop which is a Dell Vostro 1520.
what can I do to avoid the annoying mouse cursor "delay" or "jumps" when I move it inside my project ?
I have one surface and 3 aligments....
I have tried turn off tooltips on general options but... yes I dont see tooltips but the mouse seems to investigate the objects below the cursor....
In adittion,. is there a variable to control this ?
Civil 3D (2013)
Illustrator has been having a problem where anytime that I click the mouse down, it starts jumping around the screen, usually to about 2" down and 3" from the left of the screen. This is only in Illustrator though, Photoshop, and any other programs work fine.
I've tried disabling the Logitech driver too,
Running:
Pentium D 840 3.2 GHz
3 GB DDR2 667
120 GB SATA
Windows Vista Business
Adobe Creative Suite CS2
I am currently working for pepsi factory with huge machines in their factory building. My problem is that these drawings are very big and not loading quite well even in high performance systems. My current drawing size is about 120MB, without any hrefs.
View 9 Replies View RelatedWe have been using AutoCAD drawings for our facility plans. We are switching to revit and we like to convert everything to Revit models. Everything is good so far. The problem is we have no clue to have only one Revit model in out facility network and use that model for all ongoing projects.
View 5 Replies View RelatedI have a large map style drawing I'd like to slice into smaller files. I dont want overlap, but a clean line in common. See attached image for details for a 4-quadrant map.
View 2 Replies View RelatedI created some custom linetypes. When I copied them over to my drawing, the text in the linetypes came in extemely large. I really need to get this figured out as I am setting up a template for a new customer, and they want all these included.
I have attached the dwg for reference.
How do I get my Sheet Set Manager to open up each time I open a CAD drawing? I turned it off and can't remember how to turn it back on. I use command SSautoopen, set to 1 but doesn't alway work. Sometimes if I close AutoCad and reopen it I can got to drop down menu and click on .dst extension and it will open but if I close out of it it won't open again unless I restart AutoCAD. I thought I used a command from the Express Tool menu but can't find it.
View 3 Replies View RelatedI'm doing a program in Visual Basic 2010. In one of the forms I put a button that when clicked must open AutoCAD 2012 and make a drawing in it. The user will decide where to save it.The steps are these:
1. I added the references Autodesk.AutoCAD.Interop and Autodesk.AutoCAD.Interop.Common to the Visual Basic Project. That's OK.
2. I wrote this in the heading of the form's
- Imports Autodesk.AutoCAD.Interop
-Imports Autodesk.AutoCAD.Interop.Common
3. In the event Click of the Button1 I put this:
Dim acadApp As New AcadApplication 'Create an instance of an AutoCAD Application
AcadApp.Application.Visible = True 'Show the instance of the AutoCAD Application
Dim acadDoc As AcadDocument 'Create an intance of an AutoCAD Document
acadDoc = acadApp.Documents.Open("C:Respaldo TesisDibujo2.dwg") 'Open a Document called Dibujo 2
'Draw a line
Dim PT1(2) As Double
[code].....
Every few weeks when opening a drawing, my computer restarts (just plain crashes windows and it restarts automatically). This only happens using AutoCAD, no other program has done this as of yet. I have no service packs installed and I haven't seen another post that refers to this problem. When I click on "Check for solution", nothing comes up.
View 8 Replies View RelatedIt seems difficult to make small on screen movements without the tool jumping. Would it be better use a low DPI mouse or a high DPI one? Wouldn't you get better control with a low DPI one?
View 2 Replies View RelatedJust installed upgrade to 2012 on same machine as 2011. Within the drawing area of both Model & Paper space, cursor is jumping and slow across screen.
View 5 Replies View RelatedWe are running AutoCAD 2011 and 2011LT on Windows 7 with 12gb of ram and a NVIDIA Quadro 4000 video card.
The problem did not happen to often when we were on XP, but now, whenever we're in a command, the screen jumps as if snaps were turned on with 1/2" spacing. We've tried upgrading the drivers and graphics cards as well as installed all updates I could find. We make sure drawings are purged and audited and Layer manager IS NOT kept open.
recommend a wireless mouse that is best for its navigating qualities within large IV assemblies? keep the complexity to a minimum (no superfluous IV capabilities) while still maintaining important navigation qualities.
View 9 Replies View RelatedHere is what's happening:
When I open more than one drawing the second drawing that I open does not show (but is opened) I see the first drawing that was already open. If I open a third drawing, the same thing happens the first drawing shows ( but the second and third are both open).
Is this something to do with changing the Quick View Drawings Order?
Everytime I try to open my saved drawing, it just opens autocad 2012 with drawing1. I've been working on this drawing for weeks, and have saved and opened it many times without problem, and was working on it this morning and saved it again. Now, i've come back and it will no longer open. I can open other saved dwg files no problem. I've tried renaming the .bak file as a .dwg but that still won't work.
View 5 Replies View RelatedI have a drawing that will not open the objectscale window (annotative scale add/delete). I either select from the right-click menu, or type in objectscale, and nothing happens. I opened a new drawing and the function worked fine in that one, just not in my existing drawing...
View 2 Replies View RelatedEvery time I open a new drawing(without closing AutoCAD) my workspace resets ea time and I lose all toolbars and settings.
Using AutoCAD 2012
We currenlty have our profile loaded but when I open another drawing it changes the layout of the tools in my profile. I then have to reload the profile and all the tools come back to what we want. Why is this happening everytime I open a new/other drawing ?
my profiles are loaded via options see jpg attachment.
I seem to remember a command that you could input which would show you detail info about when a drawing was originally open and how much time it the drawing had been open. But of course I do not recall what the command was.
View 6 Replies View RelatedI there a way to open a drawing saved in 2011 ver,into a 2005 ver.
View 1 Replies View Relatedwhen I open a drawing that's missing an shx file I get a dialog box (see attached). I put a check mark in the "always perform current choice" item and select the "Specify a replacement for each shx file". I assume this replaces the missing shx file with the default shx file. But if I send the drawing to someone else they get the same message. Did the shx file not get replaced or do I need to do something further?
View 4 Replies View Relatedkeep getting program not responding message when I try to open a drawing.
View 9 Replies View Related(Running AutoCAD 2010 on Win 7, Core i7, 8 GB RAM. All AutoCAD 2010 service packs are up-to-date)
I have a drawing file that keeps giving me this message when I try to open it :
"Unable to open this drawing.It contains incorrect or or corrupted information.The RECOVER command may be able to restore undamaged material from this drawing."
When I recover the file I sometimes get a message that 1 error was fixed, sometimes no errors were detected. Either way, when I close it, and try re-opening (whether or not I SAVE it first), I get the same message. I have tried RECOVERALL, AUDIT, AECTOACAD (those AEC objects can be a problem) and tried changing the AutoCAD version it saves to (eg 2007). None of this works. I also discovered that if I WBLOCK the entire drawing it fixes it for ONE reopen, but becomes corrupted if I save it. This drawing is used as a 'template' (not a .dwt, just a "starting point") for other drawings, so the corruption is spreading.......
I am upgrading to a newr version of AutoCAD soon (hopefully that will fix it?), but this is really slowing down produciton in the meantime....
I am trying to bild a ramp in 3d but i've been trying with no success, the ramp have a non common shape. pls look at the acad file to take a loot at the shape.
I need to have the top part at 5531mm and the bottom part at 0 and there is another part which is at 5035mm you can see that in the drrong and the ramp must 100mm thick or something similar. also i need to do it as a solid becouse i need to export it on a different software which only ecrpts solids.