How to have “window” selection when using the “adjust space” command?
I’m wondering if there is a way to select all the dimensions needed to be adjusted in one go instead of selecting them one by one.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
That's the problem, I can't see the colored window when I go over my selection, I checked the options and I see everything seems OK...
View 2 Replies View RelatedWe are running AutoCAD 2011 and 2011LT on Windows 7 with 12gb of ram and a NVIDIA Quadro 4000 video card.
The problem did not happen to often when we were on XP, but now, whenever we're in a command, the screen jumps as if snaps were turned on with 1/2" spacing. We've tried upgrading the drivers and graphics cards as well as installed all updates I could find. We make sure drawings are purged and audited and Layer manager IS NOT kept open.
get the view command back on the list of menu commands as i seem to have lost it.
View 3 Replies View RelatedAn example is when I'm drawing a box, line etc and attempt to type "@5,-5", AutoCAD somehow jumps to a window on the side and if I don't notice will restore the window I'm working in and not complete the command I typed ("@5,-5" in this case). If I do notice in time, then I have to pres ESC about 3-4 times, which will then have me back on the command line with the text "@5,-" already typed (as if that was were I paused while typing??). The attached picture shows the dialog box on the top left, and the command line as if I've only typed "@", when after pressing ESC as mentioned the full "@5,-" text becomes visible on the command line?
Also, as a note: I've already ruled out that I'm pressing other keys that could possibly cause this...
I'm running AutoCAD (Mechanical) 2011
With the command window displayed at the bottom of the screen, everything slows down. The cursor momentarily freezes and it takes a second or two for commands to be fulfilled. Also, the command window is about 7 lines high; in the past, I have shrunk it to maybe 3 or 4 lines but I cannot shrink this wndow.
Then, when I push control-9 and the window disappears, everything speeds up to normal!
I tried turning off my internet connection and my McAfee Viruscan as well. Running without the command window makes it hard to draft. Since I type shortcuts, I figure I must have hit the wrong key and unleashed something unspeakably terrible.
I am running AutoCAD version 10 on my PC, with Windows XP Professional.
I am not able to select item and then click command icon. Every time a command has to be started and only then the items to be selected. Drafting speed has reduced. also properties toolbar is also not working. basic props like col, lay etc can not be changed from the drop down menu.
View 3 Replies View RelatedThe “window selection” selects only what appears on the screen! I wanted to select a page number located on the lower left corner of each title block of each drawing but found out that the “window selection” doesn’t keep selecting what doesn’t appear on the screen (if zoom in is applied)! For example, if I select a number of drawings and “zoom in” is applied then the window selection will only keep selecting what appears only on the screen!
Then how to let the “window selection” keep selecting all the objects regarding whether they appear on the screen or not?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I'm looking for a lisp that will allow me to switch from Model Space to Paper Space and vice versa.Looking for another option other then the "Quick View Layout/Drawings".
View 6 Replies View Relatedhow to turn off the little flyout menu that comes up when I am trying to use the LAYFRZ command and am selecting an object that is either extremely close to an object on another layer, or directly on top of an object on another layer. I am trying to quickly select a lot of layers to turn off, and when zoomed out I keep having to pick from the drop down menu which one I want to freeze.
I do not need to have this option on most of the time and would LOVE to turn it off as it is slowing me down a lot.
When in the hatch command in 2012 I go to select the layer I want to use, but only some of them appear in alphabetical order, and the rest seem to be all over the place making it quite difficult to find the layer I want. I've tried increasing the maxsort figure, but it makes no difference. How to make them appear in the correct order?
View 7 Replies View RelatedWhen I create a new document in AutoCAD, I get a weird gap of space right above my command bar that either displays a duplicate of the command bar or just blank white space. It is as if the comupter does not recognize it as part of the screen. My mouse will jump over the bar and I cannot type or select anything inside it.
View 3 Replies View RelatedI thought there is command that will crop a window area in model space to minimize the amount of objects.
View 4 Replies View RelatedI wrote some LISP programs. I would like to use the output data generated by LISP program in Command arear of AutoCAD. I Heard we can dave the output data into .dat files.
View 9 Replies View RelatedSuddenly, the multi line text editor in no longer displaying when I select "new" from within the DIMEDIT command. I'm presuming that there is some sort of system variable that controls this, but I have not been able to find it in the help files. The Mtext editor is working from the Mtext command, so I know it's not the DTEXTED variable.
View 6 Replies View RelatedI was wondering if there was a way to see and adjust paperspace viewports in modelspace. By adjusting viewports in modelspace I would like to be able to adjust the size of my rectangular viewport in modelspace to encompass what I want, while keeping the viewport on paperspace the same size (to encompass the entire print page). I would like my modelspace viewport to simply adjust the zoom in and zoom out of my paperspace viewport.
Any better method than individually zooming in and zooming out and re-adjusting my paperspace viewport.
When I go to model space I am unable to adjust the view scale. Although I can get to the prompt for a new scale value, the program will not accept my changes. Is this locked somehow?
View 6 Replies View Relatedis it possible to have Inventor adjust array elements dependent on the available space.
It should use integer numbers only- as there is room for 25.5 elements it reduces the number of elements to 25.
The array should be be dependent on a measurement to make comparision by eye obsolete, as well as the array is to produce the right number of elements as soon as the space available is measured.
- 2500K @ 4.2Ghz- 8GB - Radeon7970 -
- Xeon 1230V2 @ stock Ghz- 32GB - Quadro 2000 -
In 2012 Autocad, cannot change from model space to paper space, or paper space to model space without locking up in several drawings.
In 2012 Autocad, cannot change from model space to paper space, or paper space to model space without locking up in several drawings.
I can log into another user's computer and open the file fine. But when i use my computer or a brand new computer fitting all Auto CAD specs, it locks up. When I plot I have to reset my settings to the PTE standards every time.
I now get CAD errors when CAD is not even open. Also VTPSUHM barely works. I generally have to restart my computer several times to get it to work.
determine if Fields can be used in model space inside a block and show up in the paper space view as a correct number, (say for a detail number)? I have all of my detail blocks in model space and would like to place fields in the title blocks of the details so that they would show the paper space sheet number that they are being shown on in paper space. I have done some experimenting and cannot seem to get it to work. Or will this just not work?
1.- Details in model space are blocks, and I want to edit the block and insert a field into the detail callout.
2.- I want to have the model space detail read the paper space drawing number, and have the fields change to the proper sheet number.
3.- The result will be the that the model space block fields have changed to the proper detail sheet number shown on the paper space border.
I have a drawing that has several Paper Space tabs, and each tab has one or more viewports.
When I open the drawing, I can see all the information in Paper Space mode, and I can access the Model Space through the viewports, using the MS command. When I switch to Model Space, nothing is displayed.
So I just recieved drawings from a contractor and they placed all the multileaders and details on the paper space but when I go to change the model space things are no longer pointing at the right spot.
What I am trying to do is copy them into model space but.... when I use crtl-c from paper, crtl-v to model it doesn't scale properly.
I have tried and failed to set line weight of object after baseview command. Its very thick line and showing the 2d object views in very bolds lines when i am trying to take print it is horrible to see it.
I am using Autocad 2013 version
I'm using Photoshop Elements 8 and wondering if there's some way to adjust the space between the characters in a text?
View 2 Replies View RelatedAfter making a Rounded Rectangle I often need to adjust the rectangle in the X or Y direction to fit a certain space. As I reproportion the box the three node points of the radiused corner also reproportion, distorting the radius. Any way to reproportion a Rounded Rectangle and keep a true, undistorted radius? And even better, resize the rectangle and keep the original radius.
Illustrator CS6
When I select a hatch or polyline or any object with grips for that matter, and hold down shift to select multiple grips on the object or objects and then press my middle mouse button to pan or scroll it to zoom, the grips that I have selected de-select, meaning I have to set up the view so that all the grips I want to move are visible before selecting them.
This is only happening on some drawings (although it is most of them) and only when I use 2012 not 2011. Which system variable it is that has gone screwy that I need to reset? or is it something else?
Inside 3D Studio max, its possible to adjust the pivot center of an object to anywhere in space. So if for example, I've got a sphere in my scene and I want to have a bunch of cones spin around the center of the sphere (to create the basic shape of a sun graphic) I can just change the cone's pivot to be in the exact center of the sphere and then when I rotate and copy the cone, they will all be perfectly centered around the sphere.
Tying to do this in Photoshop however is proving rather difficult. Since the triangle representing the sun's rays is smaller than the circle representing the sun, I can't move the traingle's pivot to match the center of the sun because the bounding box for the transform isnt big enough.
If I duplicate the sun and merge the triangle and the sun together, the merge action re-adjusts the pivot to be in the center of both objects so its no longer in the correct center of the circle. I can however move the pivot point to the approximate location now because the bounding box is larger, but I don't need the approximate location, I need the exact location.
Is there a way to move the pivot to a specific coordinate? Or am I going to have to move everything onto a perfectly square canvas and snap everything to grid lines?
Is it possible.
CorelDraw X5 v. 15.2.0.686 Hot Fix 4 - Windows 7-64
If there is a tool where I can take a selection & adjust it all different directions? I'm looking along the lines of taking a text selection & doing what I did with "flounder" & "Harmonic prophecy" in the attached pic. Nothing fancy. Just something I can't figure out. I used a different program to do that flier.
View 2 Replies View Relatedwithout reiterating a lot of what is said in this thread: [URL] ......
This happen outside the potential malware infection?
if you care to not click-through, the problem is that certain commands (not all of them) simply do not disply in the command line. so the MOVE command for example looks like this:
NORMAL:
Command: _move
Select objects:
NOW:
Command:
Select objects:
same with QSAVE and who knows how many others.
I'm looking to size my model space window so that it is exactly 1280x720 pixels of viewable area for the sake of using plot to .png to create the right size images.
Is there a quick command or menu somewhere that shows the current viewable area of the model space window and allows for it to be changed?
I am using AutoCAD 2012.
