What is a good 3rd party application that can produce good fountain simulations? There are a variety of conditions, not just the kind that shoot straight up, but that flow in sheets and synchronize etc.
I have the need for right away and little time to deal with much of a learning curve. I've looked at Real Flow but too expensive, with a complex price scale.
IV 2011.
I have an assembly with a FEA simulation result. I can run a report and get the reaction forces and moments at each constraint. I would like to run a new simulation with different constraints and use the reaction results from the first simulation as loads in the second one.
Currently I do this by running a report on the 1st simulation to get a table of the reaction results. I then manually add those forces to the 2nd simulation. This takes time to type and the forces must be edited each time I re-run the 1st simulation.
Is there a way to use parameters to automate this?
How can I fix my LT so that I can draw fluid lines? At the moment the cursor jumps in increments across the screen as I move my cursor.
I can draw circles and rectangles fine (smooth, no lag) but straight lines are a nightmare. This also follows true with the "first line" of an elipse which is very jumpy.
Note: Brand new 3 day old HP 6550b ProBook, running windows 7.
I downloaded the trial version and have been messing with it for a couple of days..I really wanted to like it but I'm not jazzed in the least. Sure it works as does knockout and the extraction tool, but you seem to need to spend more time cleaning it up..why bother with a $300+ program if it doesn't seem to simplify the operation?
I'd rather do it one time with the Quick Mask and know its going to be smooth...and as for flyaway hair...extract seems to work as well as any. Has anybody have an real success with this program?
Is Fluid Mask 3 the best Knockout Plug-ins for Photoshop,
View 7 Replies View RelatedI have one layer with some outlines, everything is colored WHITE now. How can I change the color of this? The outlines is too thin and detailed to use the CTRL+U and drag the things, nothing will change.
View 1 Replies View RelatedI've seen these all over but I'm not sure if they are created with Photoshop or some other graphics program. Any ideas?
View 4 Replies View RelatedHow do I load the fluid mask plugin?
I got it in the plugin folder and one is installed from their website.
I made an animation of a small prototype engine I am designing (attached as video 3) and I would like to be able to show fluid flowing in from the injector and into the cylinder, through the dumbbell valve and out the bottom, autodesk inventor does not seem to have this capability and its looking like my only option is to learn 3ds max and rebuild my animation in that.
View 7 Replies View RelatedI'm using Maya 2012 with thirty fluid containers and the scene takes over 45 minutes to load.
What is taking so long to open the file? How can I reduce the time it takes to open the scene without removing the fluid containers?
The Fluid mask installer doesn't recognize Photoshop 6. I selected other and tried to put the “Vertus Fluid Mask 3” folder that contains the files dbghelper.dll & FluidMask3.8bf into the Photoshop 6’s plugins directory. It’s not available within Photoshop.
It does however function as a freestanding program so I know it works on the computer. It also worked very well under CS5.I’m sure Vertus will get around to upgrading, but I’d like to be able to use it with my current projects and not have to wait for them.
UPDATE: The above procedure works for the 32 Bit install of CS6... Not with the 64Bit.... would like it to work with 64bit since I edit some sizable files
How easy is it to migrate third-party plug-ins such as Vertus Fluid Mask to Photoshop CC?
View 1 Replies View Relatedi have started creating layouts in photoshop cs3 and i was wondering if there is an easy way to save my layouts as fluid width, as opppsed to fixed, so they resize according to the browser window. is css the only way to go?
View 4 Replies View RelatedI'm new to 3ds max, and I was wondering if there was a way to do a spill simulation without a plugin. I've figured out how to do a fluid simulation , tutorial [URL].........
But how do I get the water to stick to the ground. I can't seem to use RealFlow becuase I am on inventor 2013 and that plugin doesn't work for the newer model.
I wonder if there is any plugin/software that makes it possible to do some CFD simulation on my 3dsmax object?
I consider it as an additional part of my current object I'm designing, but I'm no engineer and I've got no possibility to use a real wind tunnel.
No matter what settings I use MassFX seems to explode all of my pieces/particles as if they are under extreme tension just prior to running the simulation.
I have a facade of a bulding broken up into about 1000 pieces. It's real scale and 135' tall. All I want is for the pieces to just fall to the ground. But, no matter what I do at about frame 3 the whole thing just explodes. I've tweaked so many settings that I'm completely lost and can't seem to solve the problem. The default settings are the worst. I've set the 'Damping/Linear' up higher and increased the 'Collision Overlap' but still can't seem to figure what controls this tension or pressure that it appears is in the parts before the simulation starts.
I've created a successful FEA simulation in Inventor 2014 and obtained results. But I want to see the highest stress in a defined area that is smaller than the entire part (I have some stress concentrations that are throwing off my 'max'). Is there a way to probe an area instead of just a point? I'm tired of creating a dozen probes to find the 'local max'.
View 8 Replies View RelatedI was wondering whether there is a Photoshop filter that can simulate a star filter attached to a camera lens. I like the effect of that kind filter.
View 1 Replies View RelatedHow to create or how to set a one way rotation joint as a one way bearing will work on real life, is this possible?
View 9 Replies View Relatedi have some problems combining multiple meshes in one rigid body simulation. What i want to achieve is a button containing a metalplate, a plastic body and a needle 200x multiplied and each of them should be treated as a single massfx object. This bunch should simply fall on a plane ending with accurate, physically correkt positions. My way was using all parts with a physical mesh constrained (RB constraint) to each other part as childs. This works well with one whole button, but copying shows some strange beahviour of the constraints - and doing 200 pieces manually is not the way i want ;-)
View 1 Replies View RelatedFuzor? The features are extremely amazing. I have already tired it for one week due to I am Fuzor's beta tester. The real time simulation are really excellent and I have already tired it for one week. I found that I can't use Revit without Fuzor haha. If you want to know more detail, check the website URL..... It may have more detail and I heard this software “Fuzor” will publish in AU.
View 3 Replies View RelatedWhat would be the best way to create a wind tunnel model that you can then put different shapes into to see how aerodynamic they are and look at the friction and turbulence?
View 2 Replies View RelatedI'm developing a program which runs several simulations and obtains the results automatically.
I'm using the dynamic simulation API created in Inventor 2013. For that I use the GetResultValues(ByRef values() as Double) method of the class DSResult.
I used the method inside the VBA of inventor and worked well. But when I wrote the program in Visual Basic Express 2010, the method doesn't return anything.
I share an excerpt of the
Dim odoc As AssemblyDocument
odoc=invApp.Documents.Open(testPath, True)
Dim dsman As Inventor.SimulationManager = odoc.ComponentDefinition.SimulationManager
Dim dssim As Inventor.DynamicSimulation = dsman.DynamicSimulations.Item(1)
Dim oJoints As Inventor.DSJoints = dssim.DSJoints
oJoint = oJoints.Item(1)
[code]....
The method GetResultValues(values) should modify 'values' to a time,value vector.
It works well inside Inventor, but doesn't in the program in VB, although it runs the simulations and does everything else right.
How to use dynamic simulation, i am creating a bench vise and woud like to animate it going in and out how would i do that?
View 1 Replies View Relatedwhen in simulation, if you suppress a feature is it totally taken out of the simulations workings?
I.e. if I was working on a project like some weighing scales and I had a load of objects on the scales and I then suppressed some of the objects, will the scales rise up a little to counteract the reduced weight?
Is this type of gravity experiment possible with dynamic simulation?
[URL].........
I made the cone ramp and double cone but the cone either goes the wrong way or only moves a few inches in the correct direction and then gets stuck. I’m using 3D Contact Joints and Spatial Joints and Gravity Force.
Version = Inventor Pro 2009
I am trying to discover the dynamic simulation, so I need to know is that possible to create a new Load(Torque, Force) using API?
View 2 Replies View Relatedi'm developing a hexapod robot and i want to simulate the motion of the robot's leg. The mechanical of robot's leg contain a servo motor that variate your angle between 0 to 330 degre. How can i delimite the angle of servo's rotation?
Other questions, is about the fixation with bolts. How can i do for the motion simulation respect the connection of the bolt? when i do a dynamical simulation the parts that contain bolts don't stay joints, i have to do a rule of fixation with constrains?
I'm designing multiple elements for a vehicle. I need to evaluate multiple dynamic results of multiple possible designs. All the design is parametric so it modifies quickly but I can't find a way to run the dynamic simulation multiple times automatically and get the results from the output grapher for each simulation.
I am trying to do it via API but can't find the class of the dynamic simulation environment in the Object Model Chart to program it via .NET.
I have installed inventor 2011 on my laptop, but the dynamic simulation menu does not appear even though I 've been many times to install it.
View 9 Replies View RelatedI have a very simple part I am trying to check using FEA; however when I get into the Simulation environment and click 'New Simulation' from Ribbon nothing happens.
The part in question is just a simple cylinder (I'm verifying what would be the best meshing spec to use in a larger assembly).
