VideoStudio :: Difference Between AVCHD And MPEG-4 HD?
Jun 14, 2012
I just moved from a Sony HDV (HDR-HC3) camcorder to a Panasonic AVCHD one (HC V700). When rendering my final video, I've always used MPEG-4 HD. This new camcorder records in AVCHD. I'm not sure if I should be outputting to MPEG-4 HD or AVCHD. Before I had issues rendering in AVCHD, which is why I didn't use it.
What's the main differences in MPEG-4 HD vs. AVCHD? What are the advantages and disadvantages? Which one is better and the one I should use?
View 6 Replies
ADVERTISEMENT
Oct 4, 2011
If I render a Videostudio-file of 15 minute in .mpeg, it is about 750 000 great, if I render it in .mp4 it grows to 1.200 000, why?
View 5 Replies
View Related
Apr 24, 2011
I know there must be a thread or post about the best MPEG settings when you are going through the steps to burn a DVD, but did a search and came up with nothing.
Those items in bold are checked in X4.
In the MPEG properties
● Do not convert
● Support X-Disc
● Two pass conversion
● Treat MPEG audio as non-DVD compliant
● Auto fade
● Play all
● Auto repeat
Lower field first?
Under Change MPEG settings/Customize do any of you change anything? General Tab and Compression? I know to move the slider under compression to 100%. Not sure about the rest.
View 6 Replies
View Related
Oct 30, 2010
I'm a recovering Roxio user. 6 years. Finally fed up with 2011 crashing everytime I tried to convert DVD to MPEG4. I just downloaded VS Pro X3 and how to do this. I'm assuming it can be done on this program.
View 1 Replies
View Related
Dec 3, 2013
When I burned an AVI (that I captured with VS X4) to a single layer dvd VS does the job, except that when I palce the dvd in my living room Sony player I have the following error message : The disk is dirty. I tried twice with the same result! When I capture directly to the mpeg format and then burn a disk I have no problem.
How I could convert AVI to MPEG (no menu, no edition) in a simple way?
View 4 Replies
View Related
May 26, 2013
I am using VS X6 ultimate that I purchased yesterday
I am capturing videos from VHS tape using an S-Video connection
I have tried different capture options settings and the capture always saves in MPEG
I believe that AVI has the least loss and would prefer to save in the AVI format since I intend to do some editing of the original content The end objective will be to burn reults to DVD
Can VS X6 capture files in AVI? If so, what settimgs should I use? Any settings that would be best for this type of transfer to HDD?
View 3 Replies
View Related
Oct 25, 2010
Capturing VHS to MPEG? Does this tutorial work?
[URL]
View 4 Replies
View Related
Apr 7, 2011
I did a ton of research on Video Editing software and decided to try VS Pro X4 first due to it's ease of use (good for me) and capabilities that I can grow into. So far I would say the experience has been positive and feel I could happily settle in with VS Pro X4 for the long haul, but have just a couple of questions I would like to resolve first. They may not be issues at all, but more due to my lack of knowledge, but figured experienced users like yourselves would be able to determine that in short order.
I've split my questions into separate (3) threads so that people don't have to suffer through content they're not interested in. Here's a brief run down on where I'm at and what I'm trying to do.
I'm about half-way through my 30day trial of VS Pro X4, and starting to feel a little more comfortable with the software, but a few things are still puzzling me. Granted I've only scratched the surface of the SW capabilities so far.
I'm a complete newbie to this digital video stuff, however I'm not a complete newbie to computers. Basically I have a shoeobox of old 8mm camcorder tapes (analog) and have finally decided to take the plunge and digitize them, mainly because we never end up watching the tapes 'cause it's such a pain.
First question; A friend of mine is letting me borrow his ADVC300 converter, connected to a Firewire400 card in my PC. VS Pro X4 capture works fine, was able to capture an entire 8mm tape. It was an entire tape because that's the way it was taped, it was a music performance so the tape ran through the whole show. I was able to add a simple title and burn to a DVD disc. What should I expect for MPEG compression when burning to a DVD? I couldn't fit it all on one DVD disc, had to split it into two discs, not a big deal, just thought the mpeg conversion would have compressed it more? Maybe that's wishful thinking on my part? It's a 2 hour & 2minute video which equals a large ~8.7Gb raw DV capture file through the ADVC. I know a DVD is 4.7Gb max so obviously the 8.7Gb raw file won't fit, but is 2:1 compression/conversion expecting too much for the mpeg conversion? Maybe there's some options I should be using to compress it more?
All in all I'm pretty happy with the ADVC to digital capture functions with VSPx4 so far.
View 8 Replies
View Related
Mar 1, 2011
Is it possible to Capture in MPEG FORMAT with Pro X4?
It was possible with Pro X2 but not with Pro X3.
View 2 Replies
View Related
May 3, 2012
I'm testing demo version of this product and I would like to know how to change output parameters of mpeg-4 codec (Share->Create Video File->MPEG-4-> MPEG-4 HD). I live in Europe and my video source is Full HD 25fps, but Video Studio's mpeg-4 codec has only parameter constants 30fps.
View 5 Replies
View Related
Apr 17, 2012
Today I use a dvd maker freeware program...load this mpg file and it creates the dvd folder and I create the image from that. Total size is 4.2 and it reports using 94% of the dvd available space. Freeware program puts in extra screens advertisements so can't use it.
I attempt to use the share-create disc and import same mpg file and it reports in the bar that its 6.48GB. To me this is a problem and I can't understand why it reports it as 2.2GB larger than the actual file size. There is no menu its from a new project, nothing imported to the timeline, just open, create, import and my OS and every other program must be reporting it wrong.
View 1 Replies
View Related
Apr 26, 2012
I am having a difficult time Exporting my 640 X 360 Video In an Mpeg Format, I am making a YouTube Video in 640 X 360 ( 360P I believe the size is called ) only because that is what my source video size is. My original source video is " AVI - 30Fps " I have cut and fine tuned my 8 Second Video that took me 8+ hrs to figure out how to make
Under the Project Properties there are 2 format types available, MPEG and AVI. Under MPEG Project Options --> General, I have only 4 sizes to choose from in the frame size box, 720 x 480 - 704 X 480 - 352 X 480 - 352 X 240, And the user defined selection bullet is GREYED out.
Is it possible that because im using the trial version that I just cannot fully use the software, If so then I can go back and install my VideoStudio X4, I was hoping to Upgrade to X5 because I can directly import my Paint Shop Pro Layers as well as CorelDRAW too.
View 7 Replies
View Related
Nov 6, 2010
I have about 30 files with the extension .vsp. As it turns out, I can only convert two of them to .mpeg. I'm trying to figure out why that is by looking at every single detail I can to figure out why only two of them can convert but none of the other ones will be accepted. i just get an error message each and every time. The error message says that there is a file mismatch.
View 10 Replies
View Related
Mar 6, 2013
I have been using Pro 4X for just over a year now but have recently been experiencing crashes while encoding HD MPEG files. I have also just activated/unpacked the included music with the software and these issues just started after I did this. Note: I do not use the provided music but believe the conflict is because of this.
Problem signature:
Problem Event Name:APPCRASH
Application Name:vstudio.exe
Application Version:14.0.0.0
[code]....
View 1 Replies
View Related
May 7, 2012
Working with family project (captured by someone else-not me). Gist is that the raw AVI file doesn't have any sound when I play in media player or VSX2. The avi video format shows up as mpeg4s Decoder DMO and the audio as "Unknown ACM Format". I naively used this to make an mpeg vid file and tried to tweak the audio using LPCM but the resulting file has no audio either. The avi shows the video compression as mpeg4 but when I use my mpeg4 converter it doesn't recognise it so it's obviously an avi file with an mpeg4 video compression used.
Is there any way to recover the audio in these circumstances?
View 5 Replies
View Related
May 8, 2010
Up until recently I had been able to capture a VHS movie using the ADVC-110, edit the avi files and put in transitions, save to a vsp file. Next I would go to Share> Create Video File> Custom. Since this an old movie of only fair quality I would select a bitrate of 6000. I was previously able to render 3 different movies of approx. 70 minutes in lenghth to mpeg-2 in 1 1/2 hours each. Now it suddenly takes 6 to 8 hours per movie. The cpu will go like gangbusters and render the first 50% of the movie in just 20 minutes, and then slow down and take hours for the last 50%. I have Spy Sweeper and other running progs. and apps. shut off, screen saver disabled, internet connection off and D-Link not in use. I am using my "D" drive for all my files, which has nearly 1 TB, and I have plenty of available memory. what causes it to slow down, and what I might try? OS: XP; MB: ASUS P5QL-E; GC: NVIDIA GeForce 9500 GT; SC: Real tek High Def Audio; Processor: Intel 2 Core Duo @ 3.33 GHZ; Hard Drive: C: 300 GB, D: 1 TB; Memory: 3GB.
View 2 Replies
View Related
Feb 20, 2013
My footage are .mts files and edited to .vsp files with "Lower Field First" with VS X4. I have no problems in converting to video files using "Same as Project Settings". Now I wanted to try with "MPEG Optimizer" and the resulting settings given by VS X4 are:[
View 8 Replies
View Related
Nov 20, 2011
I recently used two Camcorders at a wedding and one (Panasonic NV-GS500) when connected via firewire to VS XP Pro3 showed up straight away with DV (AVI) download option - which is obviously the quality I want/need. The other Camcorder was a Canon HDV HV30 and it only offered MPEG download quality option. Both camcorders used Panasonic DV tapes and both are HD Digital camcorders so why would one offer DV and the other MPEG?
How do I capture from the Canon in AVI? I turned every thing off (VS and canon camcorder) and this time DV option presented itself.
View 2 Replies
View Related
Nov 6, 2012
I've a professional Panasonic camera capable of 720p and 1080p AVCHD recording both at 50 or 25 frames per sec (PAL). My recent clips are AVCHD h.264 50fps @ 24000-26000kbps. I usually render the file to film first, then create a disc after. I use VSP x5
For a short edited film (less than 5gb), I'm happy to make an AVCHD full-HD disc and enjoy a seamless and lossless transfer from project to a standard disc. The picture quality seems true to the original recording.
Q1) For longer films where I need to use a Blu Ray, what exactly is the best route to take and what boxes should be (or not) checked?? I did create a Blu Ray disc using the largest output 35000kbps max and I thought afterwards the footage looked a bit "contrasty" and second hand.
Q2) I've read in the forums that 50fps for 1080p Blu Ray is not available yet (hence the conversion to 25fps). Is it available at 720P and what/where are the settings?
Q3) If I know before filming that I'll be needing a Blu Ray, is it advisable to shoot the original at 25fps to avoid deterioration at render stage?
Q4) For downsizing to 720x576 Standard Definition discs, do I need smart render on? Two pass encode? for best quality?
Bottom line = I want to avoid my footage being unnecassarily hauled through rendering hoops and the final AVCHD or Blu Ray to be as best it can.
View 14 Replies
View Related
Nov 20, 2013
The following didn't eventually cause me a problem since I have retained some earlier versions of VS. Normally, starting way back with VS version 8, I've happily downloaded avi files from my handicam, edited them and made nice home movies on DVD, worth watching even by non-family .
But now I've just been given a couple of mpeg-4 files (total time of 1 hr 20 min or so) to turn into a nicely edited DVD (it's an orchestral concert). If I insert the files into the timeline in either X5 and X6, the audio doesn't sound when I try to play either the project or the clip. Do the same with X4 and things work perfectly, audio comes through loud and clear. So I've used X4 for the task, I kept it on my computer.
An additional task was to make an audio CD - no sweat, I just created a sound file (in the "share" tab) with X4 and went from there. Trying to do the same with either X5 and X6 caused the software to crash with an error message.
error message
View 4 Replies
View Related
May 14, 2011
I have a project with only photos (about 200) and 3 songs. Total length is about 16min. I have successfully created a .MPG (2.3GB) and .WMA (474MB) HD files.
My problem is when I create a MPEG-4 HD files. It kept crashing the program while "Creating File..."
Error message, "The program has encountered an unspecified error and has stopped functioning. Please contact Corel Technical Support and send the dump file for analysis."
I tried another project with photos and music only and encountered the same problem. Shortening the project yielded the same (one song and a few pictures).
I tried using "Custom" and using the HD settings resulted in the same error. Nothing works.
My patches are up to date. How to create Hi Def movie files that I can playback with and Apple computer (Quicktime).
View 14 Replies
View Related
Dec 13, 2010
I've been using VideoStudio Pro X2 for the past 2 years and it has been working just fine since, up until mid last week. I was rolling right along, creating MPEG-2's of the Classic 39 Honeymooners episodes, until I got up to Episode 24, when I started getting the 'Failed to open the MPEG encoder' error message. I searched through this forum to find any possible solution and the only solutions I found were to check to see if the MPEG-2 encoder CODEC is installed, which it appears to be according to the InstalledCodec utility and to uninstall/reinstall VS, which I did. I still receive the same error message, however. What could cause it to go from working one moment, to not working the next?
I tried to attach a text file listing all of the installed codecs on my system, so you can look to see if the needed codecs are installed, however I was unable to attach the file...says 'extension not allowed'. How to upload the file.
View 5 Replies
View Related
May 7, 2012
I have the following problem. I've created a project which takes about 20 minutes. The projects contains foto's and video's (MTS 1920x1080). When I create an output file in the MPEG-4 HD format there is one point is my video where there is a Glitch.
There is one MTS file in my video where I see some white flickering, which is very disturbing.
I've performed some tests to try to solve the solution, but I think it seems that there is a fault or error in the VSX file.
Below I've added some of the results of some things I've have tried:
When I drag that one MTS file in my project to another location the flickering seems to stay at the same place but then in another video.
When I remove that one MTS file from my project the flickering is gone. It's a solution, but not at this point, it should be working.
When I play the video in Windows Media Player then I see the flickering, but when I play it with Video Lan then I don't see it. If I play the video on some computer with Media Player it also should be working.
Also when I export the video in the AVCHD (1920x1080P) format the flickering doesn't occur.
View 7 Replies
View Related
Dec 2, 2011
Bought VS X4 last week cause I had problems with X3... And now I really wonder why the hell I bought X4... cause I keep having the same problems.
I've tried calling Corel today and I can only get support if I buy a support card. I just got this program and I would like some purchase support or something. Cause I have this program since Saturday.
Anyhow... It never crashes, only with rendering. First it didn't crash if I rendered it in a lower resolution, but I want the highest resolution, I'm on art school and I need to show it in big on a screen.
Anyhow, with the somewhat lower resolution it didn't crash, but now it also crashes on the lower resolution.
I heard people having the problem with X3, like I had, and they had to remove all apple products. So I did, and trying it now...
View 2 Replies
View Related
Dec 1, 2012
My HP had win 7 pro issues and then blew its motherboard so i replaced it. I reloaded Video Studio Pro X3 which worked fine until I tried to save the edited video as a mpeg-4 HD (to be converted into an AVI later). It starts saving and then shut downs informing me to contact Corel and give them the data dump to figure out what the problem is. of course, i can not contact Corel who directed me to this forum. I did download and install the critical update but the same error occurs.
View 14 Replies
View Related
Jul 29, 2011
Black is not all black when encoded to mpeg2, making DVD's. Same as it was way back in 2005 and forward. At least on my TV set. Panasonic PAL. I these days have a new 42" flatscreen Panasonic compared to my old 4:3 "fat TV set" Sony Trinitron. The same experience... I want the same look, contrast and colors, as with the DV tape straight to the TV set, even if there, offcource, could be some artifacts from the encoding itself.
Here is my almost 6 years old thread on that problem.
There was a thread once, I can't find now. Seems to be erased. I have it on paper though. The subject was MPEG encoder settings in VS11+ The starter of it was Jack_HDV and replys came from vidoman, Ken Berry and etech6355. The tip in there was to add the Advance=1 in the uvs.ini file under the subject [viodriver]. I have tried this on the new Corel VS X4 but to no sucess. The mapstructure is also a bit different in W7, users vs. document and settings. The meaning with this added line was to get another button "advanced" under the tab "compression" and be able to change "primary colors" via a dropdown list.
how to do it in Corel VS? Is it maybe something that shouldn't be doable in VS, because of licence payment to the company Mainconcept who has done the encoder. VS should maybe only have the "light" version"? Just before this new thread I managed to encode with an older version of Canopus Procoder v.2, with perfect result as it comes to black and white and also a bit stronger colors. It's so much easier if we could get the same result withing VS.
View 14 Replies
View Related
Feb 27, 2011
I have yet to edit a video. I have over 25 years of videos that were made on VCR tapes. I used a Panasonic VCR to DVD recorder to transfer those tapes to DVDs. I changed the extension from VOB to MPEG. Most of them import into X3 just fine. However, some of the videos I want the most will make X3 not respond (hang).
Here is what happens: I use the "Insert Media File to Library" process. Normally, when I click on the video its name appears in the File Name box right away. When it is a video that is going to hang the program it takes a very long time to fill the File name box. Sometimes it hangs there. Once, I was able to get the video into X3 and it started but I couldn't move the scrubber and then it would hang the program.
The odd thing is that the video will play in Windows Media Player and work just fine. I don't think there is anything wrong with X3, I think it is the videos. Would I benefit from an upgrade to X4?
View 4 Replies
View Related
Jun 12, 2012
VS X5 Pro wont render clips totalling more than 6 plus minutes......Gives me one of these 2 errors >frame 724 unreadable, frame 1024
unreadable. I click on OK and poof! everything is gone!!
View 12 Replies
View Related
May 29, 2012
whether Video Studio could handle the video file format from a high end Panasonic prosumer camcorder. It seems the question I should have asked is whether Video Studio X5 can edit and export files in the new AVCHD 2.0 format, which is used not only by Panasonic but by other camcorder manufacturers and which, according to an email from a reviewer for camcorderinfo.com is not compatible with a large number of video editing software programs. Can X5 handle AVCHD 2.0?
View 9 Replies
View Related
Nov 10, 2010
I need to convert AVCHD footage to 1280x720 MOV (qt) files. VSX2 via create a video file, and VSX3 can do this via video file creation and batch conversion as well. The problemis that I can't find any setting to get the bitrate of the MOV files under contol. VSX2 generates files with very high bitrates, VSX3 with low bitrate, and when I select "check data rate" in the advanced options settings for the MOV file, I get a prompt at every new file start (and I have many files) like " the bitrate exeeds the settings...do you want to continiue" .
View 10 Replies
View Related
Mar 15, 2013
I have VideoStudio X5.I have saved my completed video as a video .m2t file and as an AVCHD file neither of which will replay on the computer if I click on the file folder. If I copy them to a USB stick they don't replay on the HD tv either. Both play as discs on my laptop quite happily but how do I transfer them as videos to a USB
View 14 Replies
View Related
