I have a load-bearing masonry wall in an existing building where I need to remove a portion of it to make two rooms into one. The wall will only be removed so that it is above the new ceiling. How do a create an opening in it that is not room bounding? I have a wall opening family, but you cannot choose whether or not they are room bounding. This only works for walls.
View 7 Replies
I have a restroom where the toilets are housed in separate "rooms" divided by full height/full thickness walls. I want the restroom to be scheduled including the area of all of the smaller rooms so I unchecked the wall's room bounding property. However, every time I reopen the project, this property, although unchecked, is back in effect. How can I get the room bounding property (when unchecked) remain the same when I reopen the file from day to day? I made a simpler file to test this, but could not produce the same error.
View 4 Replies View RelatedI would like to add a "Room Bounding" Parameter / Constraint to a Generic Family I have already created
I have successfully created a Shear wall Family for the core of a building I am modeling.
I've stacked one on top of another and linked it as a project file with a Global "Room Bounding" checked into the main Project File . Geometrically it all works perfectly and even looks right with a concrete fill linestyle. But sadly the instance doesn't appear to realize that it is meant to act like a wall when it comes to adding rooms!
I have a wall type that has an embeded sweep for the wall base. My project is set up in two phases, existing and new work. A door has been created in the existing phase, and demoed in the new phase. Where the door has been demolished an infill with the base appears, great! In the new phase I inserted a larger door that cuts the existing walland the entire infiil from the demolished door, but the base still remains. How do I get the new door to cut the base that was created as a result of the infill?
View 1 Replies View RelatedI need to insert a arch opening in a a wall. I dont have a opening folder under my door family. I tried to download openings from revit city but although i save it in my sampels file is is just not there.
View 2 Replies View RelatedIs it possible to add a standard wall opening in a wall that i have modelled in place?
I know i can add a void extrusion to the model just wondering if there's a setting i can change to allow me to use the standard wall opening comand.
I have a project in wich rooms functionality is compromised. I don't know why the room tool doesn't recognise a simple room delimited by walls whose property divides rooms is set to yes. If I place a rectangle of rooms delimiters the room tool works properly instead. If I start a new project the tool works properly.
View 1 Replies View RelatedIs there a way to demolish (new construction) an opening into a wall that is an existing phase (existing wall)?
View 6 Replies View RelatedAt Home>Opening tab>Wall in Revit 2012 I cut an opening in a brick rainscreen wall and the brick coursing turned vertical at the wraps.
View 1 Replies View RelatedI need to make a sweep along the edge of the wall opening shown in the project, but Revit does not allow me to do it.
View 9 Replies View RelatedIs the attached possible? I'm trying to cut out the plaster wrap to a wall, but can't figure out how to do it.
I've had a look at using reference planes in the door family object, but they don't seem to be able to do this?
Simply checking the wall type to wrap at only the external insert isn't going to work as I want the recess in the plaster to be away from the door frame edge.
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRefer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View Related“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
I am working in the lastest illustrator through cloud and when I go to open artwork(not through File-Open but through double clicking off an email or on desktop), it minumizes and says that there isn't enough room to open. This causes issues mostly when I need to open through photoshop to make changes through a smart object. I am using a PC, which I am not used to.
View 2 Replies View RelatedI want get the rooms dimenstions, for calculating the width of the corridors.
View 1 Replies View RelatedI am using Revit Architecture 2012 and I am trying to create a Room Tag. I have attached the file below. I want the tag to read the room name and the room dimensions. Then I would like an option to turn "Unfinished" on and off. I can get this to work as long as it is a type parameter. When I load it into the project it works well and everything is there. But if I change it to an instance parameter (which is what I want) then when I load it into the project the option to turn the "Unfinished" on and off has disappeared.
View 1 Replies View RelatedMy leader for my room tag is waaayy far away from my tag. The leader/border offset is set to 0, but that doesn't resolve the issue. (the leader and tag are in blue on the png)
View 2 Replies View RelatedCan’t edit the room tag,when it comes to edit families in the Revit. For example, the tag of the room has a “rectangle” but in the edit mode I can’t find it.
View 6 Replies View RelatedAn architect sent me his revit file, it contains the full model and all the floor plan views and drawing sheets. He has floor plan views set up for each floor and some enlarged views as well. On each floor plan view each room has a tag that contains room name and room number and every door has a tag that contains the door number.
When I create a new file and link in his file so I can then start working, doing what we need to do, adding devices, etc. The problem is, the architect's room tags and door tags dont link in, and if they do I cant see them. I've gone through every possible combination in the visibility/graphics options to no avail.
Room and door info linking in should be a basic function of revit; how could autodesk expect mech, elec, plumbing engineers to create drawings that have zero room and door info?
If it matters, I'm working in Revit 2010.
I have been dealing with a tolerance issue when trying to create room area calculations in Revit. There seems to be a tolerance that is set to somewhere under 9" if two walls are to close together it will ignore the area.
Although if you are using the area calculation this tolerance is set much finer. and it seems to work just fine. I have already tried to create a multicategory schedule but cant combine rooms and areas. I have attached an image .
I am trying to add a normal, regular, editable text box to a Room Tag. Our office is involved in a competition and we want to show the Room Name and Area (which I understand how to do and have done that) and also the required square footage that was given to us in the competition project description. Here is an example:
STUDENT SERVICES
1252 SF
REQ: 1160 SF < This is what I need to know how to do.
Once the Room Tag is placed, I want to manually be able to change that number as it pertains to each program. Is this at all possible?
I am working with room tags that has multiple yes/no features. my problem is its hard aligning text because they wont snap to centers or refernece lines. How are people working with this. It causes for sometimes the leader line when used to not want to be straight or leaves some funky angle when change scale
View 1 Replies View RelatedI have a rectangle (looks like a label border) showing up in my room tag. It's a simple tag taken from the OOTB room tag family. I'v re-edited the family, checked the parameters and values. All label borders are off, but this one looks like its either part of a separate, invisible label or a separate rectangle that I can't find to delete.
View 2 Replies View RelatedI have a third floor view that continues to show the 2nd floor room fill colors, despite the fact that underlay is off. Floor 3 is visible and present (though) I can't grab it because I don't control that work set. The third floor room fill is not visible unless I make the cut plane 10'. That suggests that the 3rd floor is out of place, I think. But it seems fine in section.
I can't figure out if this is a bug in the view range or a problem in the model.
Note that the upper range is 12'2". The bottom of the range is offset 4' to show a parapet/roof of an adjoining structure. The clip depth is not effecting the visibility of the 2nd floor room fills at all, though it does effect the 3rd objects like the parapet.
I would think the clip depth would get rid of a lower floors room fill, which I assume is associated with the floor object.
How do I change the amount of characters available in a Room Tag for the Room Name? What is the limit and can it be increased?
View 1 Replies View Related
