I am working on parsing the psd file and saving the data as per doc of photoshop 6. I need to make an image from the layer data alone with different combinations of layers selected, visible etc... and not using the merged data section in the file.
View 1 RepliesI am using AutoCad 2007. However, I do not know how to make a road cross section using xyz data.
View 6 Replies View RelatedTable styles / Data linked tables. In particular when re-syncing the table from excel, cells that should be merged become unmerged.
i have unchecked excel formatting, as i am using table styles used in autocad, i did try getting it to work starting with excel formatting, but couldn't get styles consistent, and text was much fainter.
As it is now the tables are working well except for the merged cells!
Upon trying to open a line sheet i'm working on, photoshop tells me:
Problems were encountered reading layers
"..."
"..."
"..."
Because the layer is not a valid layer. Some layers will use existing pixel data.
I have an EG and FG data band for sections that works correctly. When i plot sections and it asks me specify surfaces 1 and 2, I choose my EG and FG surfaces appropriately. Then when the section displays the Section 1 and Section 2 are both set to the EG section of that specific sample line. If i change the section view properties manually it works but I'll have to do it individually for each section.
Also, is it necessary to create a FG surface from the corridor or can i get the data band to read from the corridor section itself?
I am creating a data band for Finished Ground. I have created a Top surface from my corridor and have sampled that as well as my original ground. I am trying to add data bands to an existing cross section view. When adding data bands for the cross section, I first go to the Section View Properties, add the data band, in this case, "FG Elevations", In the "Section1" column, I pick the Corridor surface that was sampled.
The data band does not display data. I know the data band works, because I picked the original ground as the "Section1" and it gave me the elevation.
I have noticed that under the "Sections" tab of the Section View Properties, and in the "Type" column, the original ground surface has a different symbol than the corridor surface. I have also noticed that if I have only the "Draw" boxes for the sampled corridor surfaces in the section view checked, nothing is drawn the section view. The corridor surfaces seem like they are not really there. Am I not able to retrieve data band data from a corridor surface?? If this is the case how do I go about making the corridor top surface something I can get data from?
how do I plot L & X-section of Road from excel data that has chainage and RL at the centre,left and right of the chainage point?
View 1 Replies View RelatedI created some about 20 cross sections for a creek we topo'd and then went to work making the topo itself look presentable. After I was all done with that I noticed my cross sections had lost the surface data and were now just an empty grid.
When I go to edit a cross section's properties in the elevation tab the "Automatic" choice has a minimum and maximum elevation of 0. When I use one of those existing sample lines to create a single cross section the same thing happens, it's not picking up data from the surface. However, when I made a new sample line along the existing alignment it picked up the elevations and created a cross section just fine.
Is there anything I can do besides recreating all the sample lines and cross sections? I'm looking for any other way because I have already labled and put in some extra work on the cross sections and I'm hoping to be able to just recreate what I already did and drop them so it will match the linework I already did.
Testing in C3D2012, using tutorial drawing "Sections-Grade-Label", selecting 2 sections depicting the existing ground and datum. Note that the datum in the drawing stops correctly where it intersects the ground:
However, when I gather the start/end points for the section links I get points that fall outside the limits of the datum section:
The second item appears to be the daylight point, but the first item is at the edge of the section view with an elevation that makes no sense. At the other side, item 17 is the daylight point and items 18-21 do not appear to be related to anything else in the sectionview, other than #21 which is again at the edge of the sectionview. What could these extra points/links be for? Intersetingly, the same section in C3D2014 returns 1 less point and all points through item 17 are identical, but those following all differ.
I have a master shape file that contains parcel ID, owner, tax info., etc. I have another file ( access 2003 -open to better file format suggestions-) which contains parcel ID and a "yes" or " no" entry for whether or not the parcel needs a new water meter. All I want to do is add the water meter information into the other shape file. This would create one shape file with one table with all the information that I need.
Ultimately I will use the information to do a map query and find out spatially where i need new water meters.
Right now i have the master shape file connected though the “Connect to Data” feature. I also have the new data added to the drawing though the Data sources------>attach under the “Map Explorer” Task pane. I attached access file (ver. 2003 .mdb) which has two columns “Parcel ID” and “Meter”.
I right click on the shape file under the display manager and select”Create a Join;” however my water meter table is not listed as an option. Will this not work?
Plan B - I tried to Create and connect to the access file as an ODBC connection. Followed this guy’s directions to a T [URL]. But when i populate my table under the fdo connection the column headings exist ( “parcel ID” and “Meter”) but the actual data is missing. Am I missing something important?
Note: I am running c3d 2012 on a Win 7 64 Bit machine. I also removed office 32 bit apps and installed 64 bit apps to see if that would solve the problem. No go.
say you make some parcels in your project with custom data fields like: id_no, permit_no, acres_served etc. you attach an agency provided shape file via an fdo connection that has many fields of information like above.
when you right click on your parcel and do parcel properties you get a tab that lets you input the custom parcel data.
lets say you print an fdo map label showing, say, the id_no, provided in the shape file. Then in your custom parcel properties for id_no you type that in.
is there a way to make an expression to put in the other custom parcel properties that will read, say, the permit_no(id_no) from the fdo like and put that information in the custom parcel property field?
I'm having problems getting super elevation data to transfer to different drawings by means of an alignment data shortcut. I know alignments hold the super elevation data so I've gone into my alignments data shortcut, input my super elevation data, saved and closed. Now when I open my finished grade drawing, reference in my alignment and profiles, then create a corridor from that information, my super elevation didn't transfer with the reference.
I pulled cross sections and it appears is has no clue there is any super elevation data. Also, I tried bringing it directly into the drawing I'm doing my corridors in and it erred saying I must be in the parent alignment drawing. Data shortcuts are pretty much useless to me if super elevation data doesn't transfer.
64 bit Windows 7
Intel Xeon (R) @2.8GHz
6.00GB Ram
Civil 3D 2012
Civil 3D 2012
Intel(R) Xeon W3530 @ 2.80GHz
6.00GB Ram
Windows 7 Professional
I am trying to link my extracted data from blocks with attributes to an extenal source so that the table I create and place into the drawing already has the formulas I need to due the required calculations. But every time I create and place the table the formulas are not in the table. I include the columes that contain the data but it doesn't seem to be working.
View 2 Replies View RelatedWithout using scripts, is there any way to have rectangles or textboxes act on values coming from a data file? For examplle if the value in a textbox was greater than 10 coming from a data record, could the textbox change color, or any other attribute to make it change from record to recortd as it is being viewed or printed?
View 9 Replies View Relatedi have created a data band in profile view that should show a created profiles elevation, but some of the the data fields are missing irregulary. Also in the data band that shoud show the diferenece betven the tow profiles - EG and the new profile the data is missing. The EG profiles data and the surface are ok all is shown.
View 4 Replies View RelatedI've just installed Civil3D, 64-bit on windows 7(running on bootcamp) and am trying to insert a georeferenced raster image but have encountered some issues.
1. "Home tab>>Data panel>>>insert An Image" - The data panel is missing and it's also not found in "customize palettes"
2. Trying the data connect route does not work either: Display manager>>>Data>>>Connect To Data - There is no 'Data' option and I cannot connect to Data.
Is it possible to embedd data in a table so that a user can select from a group of data within one cell?
I use this technique quite often in Excel. One cell in a table can have various values: A, B, C, or D. While another cell can have a different set of values to choose from: BLUE, RED, ORANGE, or PURPLE. The user can pull down an arrow (similar to a dynamic block) and choose from a set list of values.
I know that the xmls are very important in the design data folder and we shouldn't mess with them.What about the rest of the folders. I have around 11 folders. GOST, AEC Exchange, AIT, Cable & Harness, Bend Tables, DWG-DXF etc...
I need to know if any of these folders can be deleted? We don't use AEC Exchange, Cable Harness, BIm Exchange, Design Accelerator, Tube & Pipe.
What about the Optimisation, DXF-DWG. I am not sure if I am using them unknowingly.Does this could be deleted? Is there a procedure to get rid of them.
I have many section views of a road where I want to calculate ground volumes. I have a curb in a section view and I want that Civil showed me just an elevation at the top of the curb and at the top of the road cover. Is it possible to do that? And also distances: I want that Civil just show me a distance from the center of a road to a curb and from a curb to the edge of the road.
View 2 Replies View Relatedhow to import point data that has Map Object Data also attached to it? "import it by attaching to a data source".
Example: I have a bunch of manholes. Each MH has X,Y,Z, but also Type, Invert Elevs., Pipe Sizes, Pipe Materials, Pipe Directions, Structure Type/Material, etc. etc. etc. I may have point data representing MH's, airport runway ends, trees, anything you can imagine, with all kinds of data imaginable.
I want to import this data directly into Autocad/Civil 3D as either Autocad points, lines, or closed polylines (I also have utility lines, parking lots, etc.- all with data associated with it), all with the data attached as object data. I know that anything more complex than points might be hard to explain here, so I am hoping at least for a solution on how to import points - I have 99,999 MH's and obviously I don't want to have to type all that data in one by one.
I basically suck at using sql server. I can get around using the Map workspace and the different tabs. I have never used FDO, and I am not even sure what it is.
I fooled it today by creating 99,999 Autocad points at the correct XYZ, attaching the correct object data to them, then exporting as a shp file. I went into the shp_name.dbf file and edited it to add the data I wanted by cutting & pasting from Excel. then I re-imported the shp file. but, this is a workaround at best.
Surely Map can import objects and their associated data fields, all populated with valid data! all I need is to know how to do it. I mean, if this is not something I can do directly using Map commands should I take the money I earned by surveying 99,999 MH's with my GIS data collector that allows me to assign 101data fields to each object I survey, and buy something better?
C3D 2012 on 64bit Win 7 all up to date
Dell Precision 7core 8GB RAM
NVIDIA Quadro FX 1800M
LDT/C3D user since release 12
Is it possible to add data to a feature data table? Example: The shape file data downloaded from NRCS only has the Soil number for the State. As I check out features I would like to add data for the soil name, soil group, etc. as additional columns in the data table and have it available in the future by checking the feature back in to my local information.
View 2 Replies View RelatedI have a drawing with Objects that have both Object Data and Linked data in an Access database. I need to get information from the linked table to a new linked table for each object.
I have thought that if I get the necessary information from the Linked table record to the object data for each object, I could then convert the Object data to a new link and am looking for a way to copy the data from a field in the Linked Table to the object data. There is at least one field common to both the OD and Linked Table record.
Is there any automated way to transfer this data?
In my company, they have just upgraded the old version of Autocad LT 2004 to the new 2013 and we have created menu to make our job easy. I have try to transfer the menu file .mnc to 2013 but it's not working or I don't do it the right way.
View 4 Replies View RelatedI'm working in AutoCAD Map 3D 2008 and Autocad Civil 3D 2009.
The General Task:I want to convert the object data to attribute data so that I can export it to an Excel file, add another column of data, and then import that new data as attribute data.
The Specific Task:I have thousands of campus water meter locations (a block with a small icon, attribute data, and object data) that belong to two different systems, domestic water and lake water. Each of these blocks has object data item (a barcode tag) that I want to show as a label next to the block.
However, before I do that, I want to export that barcode data to an excel file so I add a column (eventually a new piece of attribute data) that says whether or not that specific water meter is radio read or manually read. I want to then import that radio read/manual read excel file back into autocad and have an X appear on the block icon if it is radio read. I also want the barcode information to show up as a label.
My problem:I can't get the barcode object data to export with the locations in one easy excel sheet that I can simply import after I have made my changes.
Find some person on here who knows how to convert object data to attribute data.
I'm creating a catalog, using data merge in InDesign CS5.5 for the first time. I'm using dummy data to start, naming the products with a naming convention Product 1, Product 2, etc.
Everything seemed to be working, but then I noticed that the merge is all jumbled, such as:
Page 1 has Product 15 repeated, with the product description, price and other information from product 6. This repeats five times down the first page.Page 2 starts with Product name, price and number for Product 7, but the description for product 6. Continuing on page 2, everything seems one off. Product names mixed with data from the next product. Page 3-15 are the same as page 1, all Product 15 with the description for Product 6.
In short, this is very weird. I am saving the data in a CSV comma deliminated (also tried text with tab delineations.) I don't think there are any text breaks in the data, nor blanks. The odd thing is also that the preview looks perfect before I merge the document.
Here's Page 1:
Here's page 2:
By the way, all numbers (except pupil price) relay the product number. For example, Product 1 has a price of $1.00, an item number of H1, and the description "This is product 1".
I can't open my psd with properly in Photoshop, it keeps showing :There was a problem reading the layer data. Read the composite data instead?
Photoshop cc
I have added intermediate sample lines in my corridor. These sections appear in the section editor and I can make changes to the data. The changes show correctly in the section editor and section view, however, when I plot the cross sections some of these added stations do not show the overrides. They are showing the original assembly group parameters. How do I get all the cross sections to reflect the edited data from the section editor?
View 3 Replies View RelatedThe gps data from my D-SLR camera does not appear in Lightroom 4 after importing the pictures
View 1 Replies View Relatedhow to disable the cropping tool from cutting out data on layers when you do want it keeping!... its ok if you don't.. but there are times when you want to crop an image and not lose that hidden data!
also why can't you drag n'drop layers to another document tab!! its stupid workflow not to mention all the other lacking areas of CS4 tabbed ui.. like mousewheel functionality.
I've taken a color picture and made it black and white by doing the following: Layer>New Adjustment Layer>Hue/Saturation. I brought the saturation down to -100. The pencil is selected and my foreground color is black.
When I try to select the flowers in my picture to bring out their color (within the black and white image), I get a circle with a black line thru it and the error message "could not rasterize because the pixel data for this layer is not directly editable". The steps I followed are working for most of my team but some of us are getting this error message.
I have a table setup in Autocad map and am entering attribute data for the objects (Polygons). I have received a new dataset which I imported as points into the drawings which sit inside in the polygons. The points imported include one attribute data field that I want to get into my table.
In practical terms I am entering data re building heights, received a lidar file with point data relating to the building height.