CorelDRAW Graphics Suite X5 :: Designing Billboard - 3 Inch Bleed
Jul 17, 2012
I have a billboard to design. Anyways, the billboard size is 10'6''x44' and the printer is asking for a 3 inch bleed all around. He is requesting I design it in 1/4 size so I've broken it down into inches and I came up with 31.5''x132''. Anyways how would I achieve the 3 inch bleed all around? Would I design the poster in the measurements I have mentioned or do I actually need to add an additional 3 inches to the layout?
I have to design a billboard that needs to be 8ft by 20ft. What size layout should I design it in? I know I need to make sure my pictures are high resolution so it can be blown up to the proper size, correct?
.I've just finished a poster and I need to send it over to the printer in jpeg format. I would like them to have a full bleed on the poster, how do I achieve this? I
I am trying to setup an 8.5 X11 sheet on landscape to do a brochure but I cannot add any bleed lines on user defined presets.
When I go to layout>page setup>guidelines>presets>user defined presets. It only gives me the options for margins and # of columns and the distance apart.....but no bleed area
The only way I can add bleed to the layout is when I go to layout>page setup>size (bleed .125")>guidelines>presets>corel presets> check three column newsletter and check bleed area. But then I cannot adjust the distance apart during setup.
I am so confused with bleed marks for printers. Here is my example.
I am designing a postcard that is 8.5 x 3.66. I set my page size in the layout section to 8.5 x 3.66. In that layout section it also has a bleed button. I check it and type in .125 in. (what the printer requires.
So it adds a dotted line outside . which i understand. Here is my question. When I save as PDF, only the 8.5x3.66 saves and not the bleed area. I need the printer to see the bleed area. They also want crop marks.
I have 2 issues to deal with. I have a poster I've created in 11x17 but I want to make sure that I get a full bleed when I send it over to the print shop, how would I do this?
issue#2: I will need to reduce the size of the 11x17 to a 5.6in width 7in height. How do I do this? The reason for the size reduction is because I need it for newspaper printing so I need to make sure to keep my 11x17.
i have that issue i made one flyer w X4 where exist a bitmap that must be to the edge of cutted paper , so i made it bigger out of page, i close it to PDF for my printer adding a bleed limit, everything else out of page (inside the bleed ofc) appear BUT the bitmap (lens) stop to the edge of page.
There is a new plug-in for Illustrator from Onyx for banner print preparation:[URL]
Is there any macro or external program with similar functions for the preparation of banner print (Bleed, grommets, marks - see attachment) for CorelDraw?
I'm designing a simple flyer that will be printed (I have little experience in the print world) and it might need to bleed to the edges, though I'm waiting to hear back from the person I'm designing it for.
If it does bleed to the edges, do I only need to make sure that the artwork on my artboard touches the edges of my artboard? OR is there something else that needs to be done?
I'm talking about the gigantic full color signs that we often see along the highway, Billboard Signs.
I've seen them for advertising for cars, radio stations, soups, pretty much everything.
I'm wondering, what program do they use to make something of that size?
I mean, surely it's not as simple as taking an image into photoshop and creating whatever wording you want on it; then telling it to print to a massive printer.
I actually have a task set before me to design such a thing,
why (sometimes) when I export text or graphics as .eps files to my cutter it cuts the same outline up to four to five times and ends up cutting right through the backing paper. I have been using postcut with various corel editions since 1997 with no problems until recently. It also cuts random lines through lines of text which is such an expensive pain in the ass.
I started to use the production manager in flexi sign to cut my designs and same thing happens, except for the random lines but it will make up to five cuts on some objects. All text and graphics are exported the same. Has something in corel newer versions changed in relation to this?
Often whatever I'm working on in X4 disappears off the document page when I zoom in or out. It's still there (I can see it in the print preview)and I can print it, but I can't see it no matter what view (e.g., normal, draft, etc.) I select. If I select the entire page I can see the graphic and text handles, but nothing else. The only way I can see my work again is to save it, close the program, and then re-open the file. My computer is a Dell Precision Work Station T3400 running Vista Ultimate with an Intel Core2 Quad CPU, 4GB RAM, and my graphics card is an NVIDIA Quadro FX 570 256MB. All my software and drivers are up to date. The problem occurs no matter what screen resolution or refresh rate I'm using.
i´m using CRD since X3 so I think i´m quite experienced with all the crashes and uncompatibilities but now I have a problem which I can´t solve.
I made a graphic project which is quite large (2,6m x 2,0m @ 300dpi) and including raster grahics. The CDR file itself has about 400MB. When I tried to export this graphic to the png or jpg at the current size Corel X5 always crashes. I tried almost everything on many computers but always the same problem.
It looks like the project is too large for export. At this moment I desperately need to export the file to jpg or png at full resolution. Maybe X6 is more stable when exports or I have to simplify the project somehow but...
FILE IS UPLOADED here and I need to have it 2,6m x 2,0m: [URL]
I have a 900 x 500 px image in Adobe Illustrator, which overlaps a bit the canvas on the left side.
When I open this file with Corel, it adjusts my graphics so that it's centered on the screen. The AI file is centered on another point. Also, the canvas Corel creates is A4 sized. I always have to resize the canvas and then manually adjust the position of my graphics.
Question: How can I save an AI file so that when I open it at Corel, the position and size of the canvas will be exactly the same?
Entire Corel suite freezes on start up - I cannot do anything. Reinstalling also does not work - suddenly buttons on the installer dissapeared - there is no text on them and when I click them nothing happens.
A week ago I have installed service pack 3 and everything worked fine. It has all gone wrong again. And installation of the latest patches does not work anymore.
I am running Windows 7 64-bit and I've got a feeling that is must have something to do with system updates.
I often create graphics in CorelDRAW export it and inserting it into my MS Word documents and finally convert my documents to pdf. When it is vector graphics, exporting as EPS works fine: The increase in file size is small and lines are displayed perfect independant of how much you zoom in the final pdf document. When I handle bitmaps, I usually export as JPG (or PNG), which works well too. My problem arise when I have a mixed vector and bitmap image. I have imported a bitmap into CorelDRAW and created some lines on top of it. I want to export it as a whole. If I export as EPS, the final result is fine, but filesize has increased considerable. If I choose to export as jpg, the filesize is fine, but the lines are getting slightly blurry. Is there a way to get the best of both Worlds - resonable filesize and perfect lines? Maybe settings in some dialog??
How on earth do you export bitmaps cropped to the size of the canvas? This seems like the simplest functionality ever but i can't get it to work. For example, I am designing an advert for use online. It needs to be 600px wide x 150px high. I may want to use a background image or a photo that when placed goes beyond the edge of the canvas. Logic dictates i would only want to export the canvas with a web image (otherwise why would i have set an exact number of pixels.) However, Corel insists on exporting everything on the canvas and desktop. Surely it should allow us to choose the bounding area of the exported bitmap.
Just to clarify what I mean, i've included a screen shot showing and example original graphic and the export result. I'm sure there must be an easy way to do this. If it's one like this i can crop it easily, but sometimes a print customer will ask me to send them, for example, a 32pp booklet we have designed for them with each page as a JPG and to crop each one manually is a right pain.
X5 Recently have begun missing parts of print out. Tried to duplicate but appears completely random.
Output to both Full colour laser and Wide Format printers will miss either text or part of objects. Today printed the text but not the text effects. Initially closed and reopened, rebooted, However this has become a now daily feature so regardless tried reprint from the same screen so next print has everything included.
Very costly and time consuming - print preview shows all correct but output is not the same.
I have some Ai files that I need to open in X6 but they use linked images which I have, but when opening in CorelDraw all I get is the basic Ai stuff but not the linked images, is there an easy way to open the Ai file and see it as it was intended?
As a sub note I can't go back to the supplier of the Ai file to make any changes.
I just used the help file for the first time in ages and noticed all the links to the graphics are broken hence no diagrams etc. I tried to search out where they are usually stored and it gives some weird Address under properties. It's a vba so suppose it's a database? How do I restore the links without having to do a re-install?
As to the pen: How do you stop the annoying over-the-top predictive curve that happens past the node in the next section after a long drag to form the first curve. i.e. you simply want to draw a straight line after dragging out a curved section previously and you get this unmanageable curve to deal with ?
I am building a new desktop and am thinking about using dual graphics cards for my work in Corel X5. Ive seen nothing in technical specs or min requirements that even alludes to the program being able to take advantage of an SLI configuration (evga gtx 465 superclocked with 1gb ddr5).
Client supplies me with word document, I make a PDF from it and then from Acrobat create an ESP file, this is done as an eps file is much less likely to cause probs then importing a PDF, I then print from the Coreldraw file with the EPS pages no problem. The problem then arises when I have to then create a PDF file from COreldraw for the client - any EPS files in the document do not appear in the PDF - so there lies the problem.I cannot alway directly import a PDF file (often screws up) even if I save fonts as outlines. Saving as EPS overcomes most/all issues.
I have a client that I laser engrave parts with a variety of graphics, about 35 different designs that fit on 10 different parts and all the designs are different sizes on the parts. I use a fixture that holds 40 parts, two rows of 20, for each type of part. I have a master file for each part that contains a page with each graphic laid out as in the fixture so that I can simply go to the page and select the graphic in the right position for the fixture and paste it into a "lasering" file. The lasering file is just as many pages as I need to run the order and is much smaller than the master file.
That works fine now and is actually pretty quick and easy to setup, but I just found out that they will be adding about 35-40 designs a month. That will make the master file huge and very cumbersome to manage, not to mention the order sheet (spreadsheet) will get huge in no time at all. I can envision it becoming a nightmare to manage and mistakes will be frequent due to the sheer size of the files.
What I would like to do is have a spreadsheet with the graphic and a quantity and merge that into the lasering file instead of doing it manually. I am very familiar with merging data but I don't know if it's possible to merge a graphic from a database or somehow import the graphic into corel.
When I checked my computer for any any unused programs I got see this coreldraw (r) graphics suite x5 installed. When I got to uninstall it showed and error message that some sort of setup.xml is missing. When I checked this programs folder I got to see that there are two corel folders [Corel and Corel (2) ] in my C: drive. After checking all the file locations of different corel applications I deleted the Corel (2) foder. After that also corel was not being uninstalled. I don't want to re-format my computer only for this
Im using draw x5 graphics software and want to know where to find useful for properly sizing web friendly graphics. I want to build a banner and an icon for my new site.
I have created a pressure network using 8-inch diameter pipes. How would I change the 8-inch pipes to 6-inch pipes without having to recreate the network.
