I got a map in Autocad (100% done by Autocad) and i have to clip out a part of it. I put rectangle (with size of needed part) on my map and TRIM all lines around this rectangle. And after that i delete all unnecessary. But this is too complex (because map is made by thousands of lines) and it takes lots of time to do this (and i have to do many such works).
Is there a simple way how to crop out a part of that map?
I would like to crop a small part of a larger image with custom / free flow dimensions to the crop and then be able to print / export at a know print friendly aspect ration. An example would be a taking a crop of one person in a couple,from a larger image. The crop is outside common aspect ratios. Can lightroom fit the image to an aspect ratio of my liking whilst maintaining everything I have cropped?
When I crop a cdr image, part of the image disappears within the crop window. Clicking inside the cropped image reveals node locations as if the image is still there but the black lines are invisible. But, there are some objects visible in the cropped image.
when I select the crop tool, my image disappears during the entire crop process. I can only see the image in the preview pane. Why is this happening? I am using the most current version of Lightroom, and I am on a PC.
I am a labtech at a community college and look after 48 mac pros in which the students use the entire creative suite. (I only mention this becuase any answers need to consider variations in system settings or photoshop settings. college students get into everything!)
But the issue is when you select the crop tool and enter a custom constraint and crop
The image size is sometimes a full 2 inches off of what you set as a crop?! I havn't run into this before
[I do know you can use the drop down box and use {size and resolution} but I want to know why it doesnt work under custom and unconstrained]
I am missing a crop tool which can rotate the crop rectangle. Similar to photoshop's tool. I found no way to rotate the crop rectangle in gimp. How do you cut out something from an image if it needs to be rotated while cropping? I tried rotating first then cropping but it does not give me enough precision so I end up with transparent areas at the border.
Photoshop Crop won't complete when trying to crop an image. This just started a couple of days ago and I can't figure out what's going on with it. This happens in Photoshop CS6 and CC
I set up our company log which gets embossed on most parts as a sketch block in an .ipt. The .ipt contains nothing but the sketch block. To use it, the designer only needs to derive the Logo.ipt file into their part and then use the scale setting to set the derived block to the desired size for that part. The result is a scalable set of line geometry that can easily be used for extrusion or emboss that is standard for all users. It works beautifully, that is until you try to use it in a sheet metal part in 2012.
For some reason, when this same part, which works perfectly in normal parts, is derived into a sheet metal part an error pops up stating that, "Selected part does not have any geometry that can be derived." Say what?
I was able to find a workaround by directly copying the block into the sheet metal part, but you no longer have the ability to go back and scale it if needed. Even more strange, when the block was copied over, it could not be deleted from the new part.
Is this just a bug with 2012? Why does it work in a normal part but not sheet metal?
Dear Sir, In particular project, when I insert part in Assembly file, It is inserted as a Tube & Pipe run part. so that It is not Grounded automatically. What is the settings by which I can insert as a normal part in assembly file ? I have attached herewith the JPG file also.
The part i make is from solid model>The part needs to be in sheet metal.What steps do i use to make as sheet metal part and have option to flatten part.
I`m looking for the iLogic code that can change one parameter (user defined) for each (ipt) part in assembly (iam)
The one below doesn`t work.
Sub Main Dim oApp As Inventor.Application = ThisApplication Dim oAssy As Inventor.AssemblyDocument = oApp.ActiveDocument For Each oSubDoc as Inventor.Document In oAssy.AllReferencedDocuments On Error Resume Next Parameter(oSubDoc, "FH") = 15.26 Next End Sub
I would like to simplify this assembly into one seamless part for FEM calculation:The assembly consists out of parts that, in reality, will be welded together. Due to their form, there is no way to place them exactly onto each other, therefore there are slight gaps between the parts:
Now when I try to merge the assembly into one part via "simplify" --> "create simplified part" and choose "single solid body with seams between planar faces merged", Inventor does not fill these gaps (even though it displays only one part in the bottom right corner of my window). Unfortunately, the remaining gaps brings "contact" problems in the FEM simulation.
how to close the gaps and really merge the assembly into one part?
I have a part that has protrusions. When i mate that part up to another part that second part needs to have cutouts/holes to receive those protrusions.
i mainly use it in sheetmetal parts. and use the rectangular protrusions on de contour to mate up with corresponding cutouts in the other sheet. this works with positioning and also makes for a nice weld spot/area.
But also for making holes to accommodate a mold pin used in custom punch dies. I want the intervening part to receive a corresponding (propperly tolleranced) hole automatically. Much like a bolted connection does.
same for parts like circlips. i want them to automatically generate the seat in the part it's mated to. Rather than using the axle generator.
Ofcourse one can place the parts and do an in assembly interpart projection and go from there, but i want the part to generate the (predifined) modification to the other part. It would save time and also reduces problems as the parts are moved about or even removed.
I have an assembly with 10 parts in it. We use many assembly features at the assembly level (Revolve cut, Extrusion cut..etc). How to find the mass difference of each part by comparing at its parts level and its assembly level.
convert the part that I have drawn to sheet metal. I have tried to make the part from sheet metal and it did not work out at all. I have attached both versions of the part.
As soon as I open a piece or try to make a new piece, it crashes! I can open the program but can't use it! I installed it and activated it and I can't use the program at all. I have sent many error reports beacuse I have opened it many times and had it crash many times and have always given my email address. Attached is the Error Report Details screen shot.
In previous releases (2009 i think) when i converted a standard part to a sheet metal part i could recall all the sheet metal styles by linking back to the sheet metal template (i can't remember exactly how this was done, but it was possible with one operation)
In 2011 i canot find a quick way of doing this, it looks like i have to open the sheet metal template and export each different style (about 40 of them) and then import each one into the converted part. am i missing something? is there a simpler way similar to how it used to be done? Why have Autodesk made this more difficult?
As it stands at the moment it would be quicker for me to remodel the parts from scratch using the sheet metal template. I know this is the obvious solution, but seems strange to change something that worked well to something that doesn't!
I order not to hide components, i want to make a break sketch and remove a piece from a part from an assembly in the isometric view in a drawing. can i do that?
The simple question is… how can we insert a step (stp) part into an existing part file?
The story behind the question is this:
Normally when we get a step file assembly from a customer, if the part has changed, we put our part into Old Versions and save their new step file as our ipt number and replace it in our assembly file. With Vault, in order for us to maintain the history of the part files, we need to keep the original file so we can’t just delete it or replace it, so now we need to figure out how to get a step file into an ipt. The Import command on the Manage tab (with 2013 at least?) does not allow import of stp files just yet.
The only other option I can think of is to put the original part into an assembly with the step file, create a copy of the step information in the part file and use it to recreate the new (step based) part.
I am having a problem with the crop tool. It will not crop the area I want; it goes to a point and stops. It's as if it has a mind of it's own and I can't direct it. I thought it might be the mouse so I took it apart and cleaned it, and then I put a different mouse in. It still does the same thing.
I'm modeling a temperature gauge and would like to have glass over the gauge so the inside is visible. I can easily do this with an assembly, but I'm wanting to do this with a single part. I tried to derive a new part from the assembly, but the transparent part turns solid so nothing inside is visible. Is it possible to do this?
I've include pictures of what I want and what I end up with.
Inventor Professional 2013 Intel Xeon W3680 @ 3.33Ghz 12GB DDR3 RAM NVIDIA Quadro 2000 GPU Windows 7 Professinal 64-bit
I am working on the part builder tutorials for AutoCAD Civil 3D 2014. Every time I click "Save Part Family", I get the error message "Error Saving XML File".
Some times we use standard parts which we could not find in content center. We creat part ourselves. But it looks like standard part in BOM or part explorer window...
I want to change type of part to PURCHASED type and icon like other purchased parts like bearings or bolts...
Is this possible?...
It can be also assembly parts like bearings. Bearings have many parts but it looks only one part in part explorer. This is very good. I want same thing too...