My boss said i could generate an isometric view of a drawing if i have the plan, elevation, and side views (makes sense enough). how do i go about doing this? is there an existing thread i can be forwarded to? (searching "isometric" didn't seem specifically useful.)
View 9 Replies
I wanted to create an isometric text in isometric view to indicate different names in different part.
Attached is the picture for reference.I did it using dimension, check the "hide dimension" option.But i can't hide the extension line.
how to create an isometric text?
I started with a Left side view of a part and created a sectioned view right down the middle so you can see the insides from another view. the part is pretty big so i used a Break to shorten it to fit the page. I also placed a smaller and separate isometric view of the same part and want this view to inherit the same break. How can I do this? If I go into the display options of the iso view, all the cut inheritance options are grayed out and can't be clicked. I've seen this done before, but i'm sure i missed a step somewhere.
Inventor Professional 2013
Intel Xeon W3680 @ 3.33Ghz
12GB DDR3 RAM
NVIDIA Quadro 2000 GPU
Windows 7 Professinal 64-bit
Sometimes when I try to create a detail view of an isometric view in my IDW, the "detail full boundary" option is greyed out? Why would this be? If I try an ortho view it works fine.
View 5 Replies View RelatedI have a long shaft with parts mounted on. i want to section it and show the parts. i don't need to show the whole length of the shaft.
I know i can crop the isometric view, but this way i will not see the key hole which is on the other side, it's hidden.
If i make a section it 's in an orthogonal view only.
I want to make the section view, but later to transform the sectioned view to an isometry. is it possible?
is it possible to change a 'flat' drawing into an isometric type of drawing? I currently have an end view of an item that I need to draw in isometric, but it's fairly detailed with curves etc and will take a long time to draw again from scratch in isometric...
View 7 Replies View Relatedim doing both isometric view and top view of a floor plan in a single paper at the same time.
the problem is ..when i change the view to isometric.. the drawing that is intended for top view changes to isometric view also..
how can i change the view of a single object to isometric isolatedly,, without affecting the other drawings and remain in its current position?
btw im using autocad 2007.
I have been trying to plot as a PDF an isometric view from CAD. I am using CAP Studio for these 3D symbols and for some reason even though I have monchrome.ctb selected under Plot Style Table my PDF is printing in color, not all black.
View 9 Replies View RelatedAUTOCAD 2012 - Is it possible to use the array feature in Isometric view?
View 4 Replies View RelatedIs there a way to turn off automatic isometric view when returning to the model from a sketch view (in 2012)?
View 5 Replies View RelatedIs it possible to creat Single Line Isometric from the Piping Model?
View 4 Replies View RelatedI have Autocad Architecture 2011 and it was working perfect until Yesterday. I Repair and then Reinstall but still the same problem.
When I have a Parellel (isometric) View and transfer to perspective works well but when I exit from the orbit function everything disappear and the cursor become crazy. I push pan and appears the drawing I release pan and the drawing disappear. The same problem in a viewport. I setup the perspective view on the viewport, lock the v-port, save and close the drawing, then open the same drawing and the perspective view become Isometric.
i'm wondering how to get orthographic views isometric view (with some dimentions) from an object ive already assembled with proengineer (student).
View 1 Replies View RelatedIs it possible to know if the assembly view is isometric view or not.I need to perform check to get this value.
View 9 Replies View RelatedI use: oView.scale=oView.scale/2 to half each view scale. It works for base view, projected views like bottom view and left view, but it doesn't work for Isometric view. Which property should I use for Isometric view?
View 6 Replies View RelatedWhen I add dimensions to an 3d object in an isometric (or similar) view, the dimension lines get placed way off screen, and the leader lines are projected onto the x-y plane.
Additionally, when I try to add lines to an object that is far from the x-y plane, the mouse position responds to the line's location as if it were drawing on the x-y plane.
Do I have to continually make custom UCS coordinates just to draw in 3d without hassle? There are other times when this does not happen (perhaps only when my 3d object is very near the x-y plane...
when i started using 2011. I have 2 viewports active; plan and isometric view. But when I try to navigate in the isometric view, the crosshair behaves in a way I don't understand. What happens is that when I zoom in the crosshair disappears over or under what I'm zooming in on.
It's hard to describe, but it seems that it have a different origo then the view represents. When I zoom out so much that the crosshairs are visible and I try to move them upwards, they stop in the middle of the screen and then the marker becomes visible in the ribbon part of the screen.
I have tried detaching all xref's, purged and audit, checked the elevation (0). This only happens in some drawings, not all, and I can't think of a common denominator in the drawings it happens.
I wrote a program that I can give a name automaticly for all 3d solid objects.
But I want to show a little box on isometric view every names with VBA codes.
How can I show 3D Solid object's name on isometric view?
I try to show on Attachment.
When I switch from 2D top view to an isometric view my cursor disappears. This is a completely new drawing file so maybe something is not set right.
View 3 Replies View RelatedI have created an object in 3ds max and exported as dwg. file to open it in autocad. The purpose for importing that shape in autocad was to set an isometric view of that object and use it in my 2D drawings for annotation and explanation purposes.
What I am trying to achieve is to have that isometric view flattened, but in top (drafting) view along my plan section and elevations so that it looks as if it has been drafted in 2D if that makes sense.
So far I have come across two commands - FLATTEN and FLATSHOT. When using FLATTEN command I get the flattened 2d splines from that object as desired, but in that orthographic view. As soon as I start rotating the flat shape gets distorted and I cant get back to it's original flattened state.
FLATSHOT immediately comes with an error saying that it is not a solid so nothing can be projected. Explode the object then use command - converttosurface this works and I can initiate the FLATSHOT command but the shape has all this extra geometry after converting it to surface and it is not what I want.
The closest is the FLATTEN command as it also allows me to hide the back edges so that I only get a clean outline of the object. But how can I rotate it and position it in a top view, flat, along the drafted elevation and plan.
I'm currently taking an CAD program and I'm having trouble drawing a few objects in isometric perspective. These objects must unfortunately be drawn in 2D. I've drawn the orthographic perspectives for each object based on the dimensioning given however I'm unsure how to proceed on certain portions of the drawing. This is all homework and I doubt using any customization is allowed.
The first image is a top view of a fixture. I'm having trouble with the central portion which I draw by first constructing the vertical arm then using the array command.
Is there some way to create an array of this object that respects the isoplane that I drew my isocircles in?
If not, I'm able to look at the original using the VPOINT from the 1,-1,1 point and get the perspective that I want. Is there a way to use the UCS and trace over the orthographic perspective then take that traced image back to the world X-Y plane? I've tried this before but once I get it back it simply looks like the orthographic perspective.
The following drawing I'm simply having trouble drawing one particular curve which the green arrow points to. The drawing is of two perpendicular intersecting cylinders one having a slightly smaller radius then the other and the curve in question represents the edge formed by the intersection. The research I've done indicates that it's an ellipse however I'm unsure how to draw it correctly and the one I put in is simply an estimate. How can I construct the correct curve? Even if I could change viewpoints I'm not sure I could find a way to trace this one.
How to draw 2D isometric images from orthographic projections in AutoCAD as it seems many of the sites I find are either trivial or focus on drawing by hand.
I'm wondering is it possible to orientate the dimension text alligned to paper(2.jpg) but not the UCS of Isometric drawing(1.jpg).
Sometime I need to allocate my drawing with dimensioning in isometric view because its more easy to read.
I'm placing my drawing in *.idw.
Sometimes when I'm exiting from a sketch, the entire model goes back to isometric view. Is there a way to STOP this from happening?
View 9 Replies View RelatedTrying to dimension a shaft in isometric view with various diameters. I am unable to find or select the centerpoints at the ends of the shaft. This causes dimensions to be crooked. How can i get the centerpoints to display so that they may be selected?
View 9 Replies View RelatedFrom my project manager > views, I select a view, it opens in model. I change to paper space and have my plan and an isometric view (in wire frame). I go to view and select shaded with edges. Perfect, colors on both plan and isometric are where I want them, now I want to print this.
I select my print icon and change my paper size select my printer. I select extents, center the plot and fit to paper. I preview.. And my color disappears. What.. Am I doing wrong. Should I be making my paper representations from a different start?
Yesterday.. I was trying to do the same thing.. But starting with the drawing in constructs. I end up with the same, my isometric drawing looses most of its color, the windows have color as does one layer (a line showing the outline of the floor under). The plan drawing has most of the colors but some of the layers are black where in the model they have color. To further complicate the problem.. The same procedure making a first floor drawing has the plan in complete color.
I have 2 rectangles and i want to loft them by path.I want the path to be arc , but i cant draw the arc in isometric view. The objects are positioned something like thes 2 smiles. One is exactly above the other and i want to draw arc to connect them and then use loft but cant make the arc. I tried to draw the arc in Front view, but i then i couldnt use it as loft path.So how to make the arc in 3d?
View 9 Replies View RelatedI recently started drawing in cad, and i have a couple problems. At time now i am trying to learn more of isometric drawing and i have couple questions about drawing a particular figure:
21.jpg
So in there i don't know how to draw that "thing" witch i highlighted in red. I don't know at witch angle i should draw it's center(center length should be 50 cm). If I would know that, i could easily draw a isocircle above. So how do i find this "right" angle?
Second question would be about isofillets - i read here in forums that i should do them in isocircles, and i did that and i got good results - it looks very good, but the problem is, that in this drawing, it shows that those isocircles should have a defined radius - R6, R16 and etc, but if i do round corners with isocircles, i dont get that result(in R16 case radius is even way too big). So maybe there is a way to do them "right" and have them defined? I attached that drawing .
I don't know how to rotate the 3D image to exactly the isometric view (30 degree, in this case) I need. I'm using AutoCAD 2005. how exactly to draw curves right in isometric view without using 3D?
View 9 Replies View RelatedI need to check if all my three views are correct.
I attached the dwg
How do I annotate the views?
How can I make a drawing in isometric?
View 9 Replies View RelatedI am working on 3d model of interior and I have two problems. I am trying to made similar model as it is on the first image.
After setting all render properties and turning on sky and illuminations my view on object switch from isometric to perspective view.
Is there any way to change it to isometric view so the point of view do not change position at the time of changing, because I find out the way to return it to isometric but then the point of view that was placed inside of room is moved outside and I can't render object that was inside.
Also I can't set white background as it is on the first image. Second image is my attempt that is made inside of the room.
1.2.jpgexample 2.jpeg
