AutoCad :: Calculate Square Mm Of Area?

Nov 5, 2013

If I want to calculate the square mm of an area, how do I do so? I know this should be really simple but I can't get the results I want. Let's say I have a rectangle (2D) and I draw somew circles and polylines within it that are 'cut out' from the rectangle....how does one calcualte the remaining square mm?

View 9 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: Calculate Area Using Polyline - Calculation Not In Square Feet?

Dec 16, 2013

I was just wondering why when I try and calculate an area using a polyine, I am getting a readout of 1.80401967E+07, when I have it set to give me the calculation in square feet? It is an area of approx. 246 Acres.....is this because the area is so large? I am not sure what the "E" stands for or the "+07" at the end....

View 6 Replies View Related

AutoCAD Visual LISP / AutoLISP :: Diesel Expression - Display Area In Square Feet Not Square Inches?

Feb 16, 2010

How I can update my diesel expression to display the area in square feet not square inches. See expression below.

^C^Cattdia;0;_-insert;AREABLK;1;1;0;$M=$(getvar,AREA);attdia;1

View 9 Replies View Related

AutoCAD Civil 3D :: Area / Square Area In Closure Summary Of Mapcheck

Oct 23, 2012

How to changes the settings for the "Square Area" in mapcheck's closure summary.  When I right-click the dwg name in the Settings tab of Toolspace and choose Edit Drawing Settings, then Ambient Settings, I see the Area settings, but in the closure summary, there is also "Square Area".  Why are these both there?  It WOULD be nice to show sq. ft. as well as acres, but I can't find anywhere to edit it.

Civil 3D 2012
Windows 7 Enterprise SP1
Dell Precision T3400
(Q9550 @ 2.83 GHz)
8GB RAM
Nvidia Quadro GTX 650 Ti BOOST

View 2 Replies View Related

AutoCAD Architecture :: Calculate Square Footage

Jan 6, 2014

I need to calculate square footage quickly.  I am currently polylining everything. Here is what I need to do quicker:

Calculate square feet of each room with these requirements:

- When meeting a hallway to the outside face of the wall
- when next to an adjoining space, to the midpoint of the wall
- When against an outer wall, going to the face of the wall. 

View 3 Replies View Related

AutoCAD Map 3D :: Calculate 2D Area In SDF?

Jan 27, 2011

i created new polygon´s SDF (ACAD Civil,Map2011). And created new feature from geometry (from 2 closed plines - island). See on attached picture. If polygons are more complex =erroneous result from calculation ("Round ( Area2D ( Geometrie ), 0 ) "). It means ACAD  calculate sum 2 areas together, but It should dedust island from main polygon.

View 3 Replies View Related

AutoCAD .NET :: Calculate The Area Of Layer?

Oct 7, 2012

How to Calcuate the area of a layer, through .NET API ?

View 9 Replies View Related

AutoCad :: Calculate 3D Polyline Area

Apr 1, 2005

Is there a way to calculate a (closed) 3D polyline area ?

View 8 Replies View Related

AutoCAD Inventor :: Calculate Paint Area?

Jun 8, 2012

How do you calculate paint area?

We do a lot of chutes (for mining).  They need to be painted on the outside only.  They also need to be lined with rubber sheet on the inside.  The area given in the physical tab in iProperties is the total area.

The area of the edges of the plates are small enough that we can ignore them, but is there a way to calculate half the model's area and get that result in the drawing in a text note?

We've only recently switched over to Inventor (used to be on Solidworks, where we had the same problem).

View 2 Replies View Related

AutoCAD Inventor :: Calculate Area For Surface?

Nov 13, 2013

I have a cast aluminum part I need to calculate the surface area for our plating process.  I have done a simple area, its not right (.015ft^2).  I have derived it as a surface but can't get a volume calculation.

View 9 Replies View Related

AutoCad 3D :: Calculate Surface Area Created

Apr 19, 2012

I have contoured an irregularly shaped site that is required to be covered completely by a liner. Is it possible in autocad 2002 to get the area of the surface i have created?

View 1 Replies View Related

AutoCad 2D :: How To Calculate Area Of Curved Line

Jul 9, 2013

I have a bench which I have drawn in CAD, and I want to calculate the area.

The bench is a sort of "S" shape.

In the past I have only calculated the areas of straight objects and so have been able to pick points, but i'm not sure how to go about it when the object includes a curve.

View 9 Replies View Related

AutoCAD Inventor :: Calculate Area Of Extrusion Without User Parameters?

Jul 11, 2012

I have a part with very irregular shape created by projecting geometry of other parts. 

I wondered if there is any way of calculating area of this extrusion instead of dimensioning the sketch and creating equasions in user parameters?

View 9 Replies View Related

AutoCAD Inventor :: Can Calculate Total Surface Area Of Manifold

Sep 23, 2011

I want to calculate the total external surface area of the attached manifold.  When I use the iProperties tool,  it give me the surface area including internal surfaces of tubulars etc. 

View 1 Replies View Related

AutoCad 3D :: Calculate Area Of The Roof Using Command Edge Mesh

Oct 13, 2011

I need to calculate area of the roof created in 3d autocad 2009 using the command edge mesh.

I cant convert it to solid or anything else. This roof if created using 4 arcs joint together in 3d environment and with command edge mesh.

View 1 Replies View Related

AutoCAD Civil 3D :: Map - Calculate Area-proportional (weighted) Average Out Of Metadata

Aug 6, 2012

I have an acad document connected to some .shp files, which contain polygonal shapes with some meta-tags.

I want to achieve the following: draw a polygonal shape and select all the tangent areas (I already know how to do so)take a property of those areas and calculate an area-proportional [or: area weighted] average value  (proportional to the partial area defined by the drawn polygonal shape). I tried to achieve this by splitting the objects and merging them again with defined splitting (area proportional) and merging (average) options. The problem is: splitting & merging doesn't work until I disconnect the data files (checking the objects out doesn't work) and even then I can't split the areas. And, more important: This doesn't create a weighted average and I don't even want to manipulate the objects! I just want to get one value out of all these steps.

I appended a screenshot of my file. E.g. I want to take the value 923.2 and multiply it with the corresponding area percentage it represents in the drawn shape. So the calculation would look something like 0.02*923.2 + 0.2*926 + 0.12*945,9 [...] until all the 100% are covered and I get one single representative value.

I use AutoCAD Civil 3D 2012 on an Intel Core i7, 12GB RAM, 64bit Win 7 Pro SP 1 PC.

View 9 Replies View Related

AutoCAD Civil 3D :: Calculate AREA Of Cut And Fill Between Alignment And Surface Profile?

Aug 18, 2013

How to calculate the AREA of cut and fill analogous to the volume of cut and fill between surfaces, but instead only between the alignment and the road profile in the prolfile view. From what I've read of similar posts a few people have had the same question but have been instructed how to do it with volumes as opposed to area. Also how to insert a table of cut and fill area analogous to the one you can inset from the volumes dashboard.

View 5 Replies View Related

AutoCad :: Calculate Large Areas Using Fills - Hatch Not Showing Area

Jul 10, 2009

I've been trying to calculate large areas using fills but I keep encountering a problem with some of the hatches not showing an area and thus ruining my calculation. I've found out that I can correct it by removing certain crossing point between lines as is shown below in my screenshots. Is there any reason this is causing a particular problem and can I avoid it to save me having to go back over my hatches checking for these malformed hatches?

area.jpg
altered.jpg

View 8 Replies View Related

AutoCAD Inventor :: Calculate Paint Area Of One-side Open Container With Double Bottom?

Nov 8, 2012

How can Inventor calculate the paint area of a one-side open container with a double bottom?

The container should be painted at the inside and outside.

But not the hollow space between the double bottom and the real bottom?

View 2 Replies View Related

Revit :: How To Calculate Surface Area

Sep 9, 2011

how to calculate the surface area, I had uploaded the attachment file,

View 4 Replies View Related

AutoCAD LT :: Area Calculation For Square Footage?

Sep 11, 2012

how the area calculation works for finding the square footage of a dwg.

I can easily get a rough estimate of square footage on L X W....but when i use the area measuring tool, i get total inches and a total sq foot estimate of 1.7xxxxx which i don't understand.

View 4 Replies View Related

AutoCAD 2013 :: Obtaining Square Footage Of Area

Mar 11, 2013

I used to be able to obtain the sqare footage of an area with the AREA command. A list would generate about seven or eight lines, listing the square footage, inches, perimeter etc.

Now all i see is one line; the area/perimeter (see attachment). Did i change a setting somewhere to obtain this simplify version of the AREA cmd? Something is not right...

I tried the MASSPROP and MEASURE GEOM, those will not show the square footage. This used to be so easy, what am i missing...

View 2 Replies View Related

AutoCAD Civil 3D :: Area Units Displayed As Square Feet?

Jan 18, 2013

In Civil 3D 2013, when I execute the _area command, i get results in square feet as opposed to acres.  Under the ambient settings, the area unit is set to acre. how to get C3D to display my area in acres?  I just want it to list the area, not label it.

Also, is there a way to get it to display the area in BOTH acres and square feet?

View 6 Replies View Related

AutoCAD Visual LISP / AutoLISP :: Draw Square By Area

Nov 27, 2013

I would like to be able to draw squares by the area they should have. So that if I need a square of 50m2 autocad automatically draws a square of sqrt(50) x sqrt(50)

Because right now I have to draw 200 squares with 100 different areas and I have to calculate and manually draw each one of them.

View 8 Replies View Related

AutoCAD 2013 :: Get Area Option Of Rectangle Command To Work In Square Feet?

Jan 10, 2014

Is there a way to get the Area option of the rectangle command to work in square feet rather than square inches?

View 9 Replies View Related

Photoshop :: Cropping Non Square Area

Jul 6, 2013

I have the following psd file which my designer provided for me: 

It's made up of all layers and smart objects and all stuff I have no clue about it. I need to make it so only the bubble is isolated, and everything else is eliminated (i.e. the character and the three bubbles going from his head are gone). Cropping almost works, but as you can see at the bottom the bubble if I try to do a rectangular crop it will catch some of the characters head and the three bubbles.

View 2 Replies View Related

CorelDRAW X4 :: Area Calculations - Square Inches

Sep 18, 2008

Is it possible to draw a shape in Corel Draw and get the area from it?  IE: Square Inches. 

View 14 Replies View Related

Xara :: Shadow Inside Area Of Square?

Feb 23, 2011

I create a square, 300px by 300px. I duplicate the square, resize to 200px by 200px. Highlight both, press Ctrl-F4 and remove the inside box. What I have left looks like a picture frame. Is there a way to shadow the inside area? (the part I cut out)

View 5 Replies View Related

GIMP :: Make Free Select Non-square Selection Perfect Square

Mar 22, 2013

I used the free select tool to free select an area of an image that is not a square (odd shape), how do I make that selection a perfect square if pasted to new image or new layer??? rectangular would be fine too...

View 14 Replies View Related

AutoCAD 2010 :: Choosing A Plot Area - Non-active Area No Longer Grayed Out

Apr 6, 2009

I've recently migrated from AutoCAD 2008 (non-industry specific) to AutoCAD 2010 so I don't know if this was an issue in 2009.

Back in 2008, when I choose the 'window' option when specifying a plot area, AutoCAD would show the workspace so that I could manually select a windowed plot area, and at the same time the whole workspace would be greyed out except the previously active window area.

This was handy, because we can have as many two dozen title-blocks (and therefore separate viewports) in paperspace, and knowing what plot area I last plotted or added as a saved page setup.

In 2010, it no longer does that. I now have to rely on the dashed border to know where the active plot area is/was (checked 'display printable area' in options>display tab) which I personally don't really like using.

View 9 Replies View Related

AutoCad :: How To Draw Line Based On Area Of Encircles Area

Oct 12, 2011

I want to know if there is an easier ACAD solution for drawing. In the given triangle of ABC (sides and angels are known) I want to draw line CM so that the area of BCM becomes 2000 cm (are of ABC is 5311.7 cm3).

Is there an easy ACAD way for drawing this line without using trigonometry for calculation?

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved