I'm going to take the computer home tonight so that I can set up as many drawing templates that I will conceivable need at work.
Are there any special ways to go about this or CAD standards that I should observe?
I mostly use A3 and A4 paper for architectural metric drawings.
Is it worth making me own templates so that I can just jump into future drawings or is it better to download templates from the internet?
Have more than one drawing template? (we use A and B size sheets)
My questions concerns, metric vs imperial A vs B vs C etc etc drawing sheet size title block does not scale down accordingly when change sheet size within an existing drawing template.
Is it possible to have one drawing template that can be toggle imperial vs metric, and then sheet size selected and then the title block scaled down or up accordingly? (I would assume this could be done using iLogic)
Or is it normal to have different drawing templates for sizes and units?
we have just upgraded from Inv 2011 to 2013. I am trying to create the drawing templates in 2013 by using the blank 2013 template and then copying our border from 2011 onto it. This works a treat apart from 1 thing.
The i properties do not get copied over as well so the sheet is blank from drawing number, title and the custom properties etc.
I have a problem in which when i set up my title block templates, when i set them up and keep my template inside the dashed area the printed dwg is either cropped or too far inside so it has to be well outside at the top to print within 10 mm of the actual paper, attached is an image of how i have to do it to make it print within 10 mm of the edge of the paper print.
View 3 Replies View RelatedI was able to draw A1, A3 and A4 title blocks in model space before giving each of these title block drawings a layout paperspace tab at the correct paper size.
I wanted to be able to start new drawings with the title blocks and paper sizes already done.
But what happens when the beginning of a new drawing project is with a drawing that someone else has already done? I am starting a new project and I would like to focus in one one room in a large building. This means that I plan to end up with a 1:50 drawing of a room on my pre-set A3 sheet and title block.
Do I import this person's drawing into my drawing of the three title blocks in model space with the three paperspace tabs or do I import the title blocks into the other person's floor plans?
I have trouble modifying the title blocks for the map book templates . Is there a specific folder that I need to save the adjusted title block in. Going through the block editor doesn’t work so I’m exploding the block and once I do that the links have been broken between the title block and map books.
View 2 Replies View Relatedi am trying to set up templates at a new job and i want to create templates with an xref for the title block so when we start a new drawing, we use the template, save to the project file and everything is there with our title block already xref'd. my problem is, the path on the xref'd title block stays the same and is still referencing the location of the file i used when creating the template. if possible, when i save the new drawing to the project foldeer i want the xref to also move to the project file and the path to the xref to change.
View 4 Replies View RelatedI want to import default templates (Title Blocks) with in Auto cad. Is there any option ? How to proceed?
View 3 Replies View RelatedThere don't seem to be any title templates in my new Premier Pro CC.
I have also installed CS6 PP as I want the Encore program - the templates are loaded in that version.
Is there a logical way to use a Title Block and border page that I created for use on an ANSI size A page to create an ANSI B, C, D? Scaling seems to work in one direction (x or y) but not both. Stretching doesn't solve my text in the Title Block from appearing too small when I create a D size.
View 4 Replies View RelatedI would like to know how I can edit my Title Block at the bottom of my page. I used to be able to select it in the past when opening the new template file. However after I performed drawings in the model window and back to the layout, I cannot click or edit the field anymore. I tried highlighting using my mouse, shifting layers and exploring right click commands but nothing good came up.
Refer to the attachment what I mean. I am running AutoCAD 2013 and I am on the "AutoCAD Classic" theme.
I tried doing a search online and on the forum with keywords such as "edit title", "edit name" but nothing relevant came up.
Capture.jpg
This is probably very easy, but I cant figure it out. Whenever I try to type text on the spine of my lightroom book, Lightroom puts it horizontally. I like to rotate the text on the spine of my book by 90 degrees so that it reads from top to bottom, like on any normal book. How do I do that?
By the way, when I start a new book, the spine text appears correctly by default (rotated by 90 degrees). In my existing book, the text cursor appears only for horizontal flow however, despite using the same design template. Is this a bug or did I accidently change the orientation of the text?
I have created a drawing template in C3D with layers, blocks, descriptor keys and all the fun stuff, but this was just for the survey section of the engineering group I work with. Now the engineers, who had another template set up with design layers which they don't use but may want to use, asked me if I can add their layers to my template. The have about 2000 layers and I do not want to manually add this information. Is there any way I can either export their layers or merge the layers?
View 3 Replies View RelatedStandard sheet number option gives you only 1, 2 and so on.
I want A1 where A does not change and 1 changes depending on sheet number.
I want to change the Arrow Side Position for Weld Symbols from Top to Bottom for all future drawings. I have opened the Drawing Template (Standard.idw) and opened the Styles Editor and switched the Arrow Side Position and saved the template. Then I have tested. In the template it works good, but when I open a new drawing (based on the template) the arrow side position didn't change.
View 4 Replies View RelatedThe title page of my photobook has disappeared, and pages 2-3 now show in the pages panel as "title page". Can I create a new title page and put pages 2-3 back where they belong?
View 4 Replies View RelatedI wanted to get opinions on the most efficient way of creating & saving title blocks, with regards to using them in future projects.
1. Create a title block in model space then save it as a .dwt file
OR
2. Create a title block in model space then save it as a block
I can't imagine there's a right or wrong way, just wanted get your input. Chances are you all know something I don't.
I created a standard title block template drawing for my student classwork exercises, and when I constructed the title block I keyed in real dimensions to ensure the title block would completely print on a piece of 8.5 X 11 paper. Now whenever I attempt to draw a large scale drawing (say a 36" dia circle, it draws the circle well outside my title block. I know why this is happening, I just need some tips about how to allow a title block template to be constructed around my current drawing reguardless of the drawing scale.
View 5 Replies View RelatedIs there an add in or something for faster type in the title block in a drawing? Name, title etc?
Right now the author and date are automatically but when i save the file to for example to "D1234 hammer" it becomes the part number.
I have to edit the title.
I want to save the file to "D1234 hammer" and the partnumber to be "D1234" and title "hammer".
IS there a add-in that I type the title and name and its auto fill the title block? Or do I have to create a custom title block so the drawing can understand to only to take the numbers from <part name> and the letters becomes <title>?
How do I insert a title block into my drawing?
View 9 Replies View RelatedWe are going to be making a new title block and I have been looking at ways to get the new title block into the old drawings. It looks like the Inventor Drawing and Resource Wizard is the way to go.
The steps seem pretty straight forward and simple but I am not getting the correct results. For the source drawing I select my new title block and leave the boxes for borders, my new title block name, and sketched symbols checked. I then pick my drawing I want to get the new title block in. On the last step I can select Yes or No and get the same results. When I reopen Inventor and the drawing it still has the old title block in it.
I'm having trouble inserting my title block in a 3D drawing. I'm kind of new to 3D modelling but it's probably a small mistake i'm making.
I started with my view in SE Isometric, drawed something and then I copy/pasted my title block from another drawing, all in modelspace.
My drawing is 3D and my title block is 2D but in the wrong position.
i have a more then 10 folder with one common x-ref i want to attached that x-ref like title block in all folder drawing how i ll attached in easy way also i want multi printing folder how can i send print in one time all folder
View 6 Replies View RelatedI am trying put drawing numbers on my drawings. The drawing number is "019-02-00038-x" where "x" is the page number in the set of drawings. How do I set this up? Every time I try to change "x" it changes it for the entire set of drawings.
I'm working with Inventor 2014.
Is it possible to set the drawing Scale to the Title Block? Seems like it is missing parameter...
View 8 Replies View RelatedIs there any command to fit or re-size a title block to A drawing in the layout?
View 4 Replies View Relatedfind a template with a title block that i can insert my information. I already have my project completed on a 24x36 sheet and would just like to copy it over.
View 3 Replies View RelatedI created a drawing in model space about 75' x 75'. Then created a title block drawing in paper space. Now would like to mesh the two so I can plot the drawing with title block. When I insert the title block drawing it is so tiny it can't be seen. What am I doing wrong?
View 3 Replies View RelatedI need to extract data from AutoCad Drawing using C# or VB.Net.
I have a Title Block which is not inserted using attributes. It has some horizontal & vertical lines drawn to look like a table and text added between them. See the attchment.
I need to extract data from that and display in Ms-Excel or in a datagridview.
I was curious, when creating multi sheet drawings, how can I place different information in the title block on each drawing?
Example, 2 pages, Description on page 1 = PAGE 1 DESC, by default this same description will show up on all subsequent pages. How do I get page 2 description to be different?
Inventor 2014 PDS
Can I pre-fill some of text in my drawing’s title block under the “Field Text” –“Edit Property Fields” ? Because some of the files I will use the same text again and again, if I can save the pre-fill text title block in the template, it will save me lots of time.
View 6 Replies View Related