I'm working on a 3D model that will include a part which is an 11/16" O.D. tube which get's flattened on one end to form a bolting lug. I have never really tried to model a part like this in AutoCAD .
View 9 RepliesI have tube that has been generated on frame generator and notched to run into the side of another tube.
Is there anyway of unfolding the tube to provide a flat profile.
What i ultimately want to do is print the flat pattern off at 1:1 scale, cut it out and wrap it around the actual steel tube to be able to trace the profile onto the tube so i can cut the profile roughly before offering the two tubes together.
I am able to extract an flat pattern (for round to square) but not exactly as the customers drawing.
The original drawing shows some relief in bending lines which i am not able to add in inventor. after a glance at the attachments you will clearly understand what i want.
I have a question about calculating the maximum tube length. Why do i ask this, because you can just measure it on drawing?
I'm building a parametric model for building simple storage tanks, and the goal is to get a complete BOM out of the model without any difficulties.
I have 4 possibilities of tube positioning on the tank. (see image)
1. A tube that stands in the center of the axis of the main tank.
2. A tube that stands in the center of the axis of the main tank, but under an angle
3. A tube that doesn't stand in the center of the axis of the main tank.
4. A tube that doesn't stand in the center of the axis of the main tank, but under an angle
These 4 possibilities can be flush with the inside of the tank or not.
Is there a easy way to determinate the longest point from the front of the tube? This longest measurement will be the length i need to get into my description for the BOM.
How do I repair a tubing constraint?
I use tubing in inventor, I always attached tube to whatever fittings I am using and everything is fine but if something gets moved that the end of the tube loses its contraint I'm ready to jump off a cliff!
Is there any way to get the end of the 3D sketch contrained to the fitting again?
Up until now I have always had to deleted the route and started over. Inventor Pro 2014
I want to build a pipe or tube frame and use tube or pipe connectors to join the pipes.
What is the best way? "Tube and pipe" or "Frame generator"?
when I use the flat brushes to paint the colours are not flat but are of different tones of the color in the shape of the brush.
View 1 Replies View RelatedI can't find a way to create multi flat patters in one part from a lofted sheetmetal part. Also, didn't the developers fix the 'can't make a flat pattern from a derived part'?
IV 2010 Suite
Digital Storm PC:
EVGA & Intel components
Win 7 Pro 64 bit
I am trying to export geometry found in a flat pattern sketch overlaid onto the flat pattern.
Since I am creating the output file manually I gather the flat pattern boundaries and bend center lines for output to a file.
When I add flat pattern sketch entities to the mix they do not overlay properly. What matrix would I have to push the sketch entities through to get them to the same coordinates as the flat pattern?
What way do i add tube to the connectors.Should it be added in assembly or as a separate part?
Inventor 2013/2014
How to create spikes on tube. I've try several way, but no success. I've try to mate with holes on plate and than to bend half of the plate, but not succeed.
View 9 Replies View Relatedhow to get the tube and pipe add-on? I do not already have it and I have not been able to find much information on how to get it.
View 9 Replies View RelatedI have made some 3D railings in AutoCAD 2013 and I am trying to dimensionthem, but am having trouble. When I create it I can snap to the center of thepipe, but am unable to snap to the edge anywhere along the pipe. This is anissue because one of the dimensions I need to show is the distance from theground to the top of the railing. When they are verifying everything it's verydifficult to measure to the center of a pipe when it's all welded together, soI need to get the actual edge. I know I can use FLATSHOT and create a 2D viewout of the 3D model, but I am hoping there is a way to do this without havingto convert it. The main use of the 3D view is ease of creating projected andsectional views without having to manually redraw each view.
View 6 Replies View RelatedDesigning a tailing dam I use a corridor model witch changing slope grade from 1:2 to 1:2.5.
There are assemblies and subassemblies with shapes defined for each slope grade, but how do I make the transition from one slope grade to another on?
In corridor properties I included two regions for each slope grade.
For grading there is a transition function. But the transition for corridor?
> In Inventor , here we see the orange color tube shown in the attached screenshot.
Attched File : Frames11
> But after zooming it nearby it’s get disappear as shown in the attached screenshot.
Attched File : Frames12
> One more shocking point is that we open this same drawing on other PC and there it’s display corrrectly.
Any solution for this hide tube. We are using:
Software : Inventor Ultimate 2014-64 Bit
Hardware : Workstation Dell Precision T3600
Im trying to reproduce the part attached. Its a rectangular aluminum tube. .320 x .180 approx an inch long. I tried lofting 2 sketches but the result does appear like the attached image.
View 8 Replies View RelatedI'm trying to do a usable and real flat pattern for a laser cut on this type of part and I'm not able to do a cut across bend or other wrap around face feature.
Any method to do such a feature ?
What is the best way to draw pipe frame using "KEE KLAMP" connectors?
Pipe and tube or frame generator?
I've been trying to make tube between these circles but I can't figure it out how to make it smooth. I tried sweep too but that didn't work too well. Here's picture of my try without sweep: [URL]
You see that it leaves corners on the back. I would like to have it so it's smooth and has same angle. How should I do it?
I inherited this assembly from another user. In making some dimensional changes the pipe runs have now errored.Not having ever taken any training courses in T&P, my knowledge is just based on simple straight forward runs.
This on the other hand is bit more complicated. As you can see from the image I have this one run that has errors.My question is with the violation, is there anyway to pinpoint exacty what the violating member is?
I have several parts to get cut for one of our customers.
The provided the pdf I have attached, and I need to create and .ipt so we can cut it on our tube laser.
This is getting the better of me on how I would put my work planes in order to get the correct angles.
How to accomplish this?
Lenovo Think Pad
Windows 7 SP 1
64 Bit.
Inventor 2013
ACAD Mechanical 2013
I'm just getting started using the Tube and Pipe environment for some of my work, and I've got what I'm hoping is a simple question with a simple answer. In the picture attached I've got a 1" pipe dropping down into a 8" pipe which I've disabled because it's a standard part right now and I want to replace it with a tube & pipe run. The thing I seem to have the hardest time doing when routing my pipes is aligning/offsetting my nodes with existing geometry in the assembly. In this case I want the end of the 8" pipe to be 12" offset from the centerline of the 1" pipe, and for the 8" pipe's centerline to be 12" below the bottom of the mezzanine's I-beam (as the standard part it is now). What's the best way to do this in the Tube and Pipe environment?
I tried "Include Geometry" from the "Create" panel but that only lets me create planes, which won't work with offsetting from the 1" centerline. However, SOMETIMES (it's a big sometimes) ALL of the options in the "3D Sketch" tab are available. When that's the case, I can go to the "3D Model" tab and create workpoints, axes, and planes. Sometimes, though, they're not all available, and I'm not able to place anything but planes. How I can change it so I can always use all the geometry of my assembly?
Also I'd like to know if constraing fittings and point-snapping routes to my assembly geometry in this way is the best way to do Tube and Pipe routes. Will doing this allow my routes to update if the assembly changes?
I have just completed an assembly and in this assy. I have a tube and pipe run. The original frame holding this pipe was 1m*1m*2m. We are now building a smaller unit with the same design. The pipe run is exactly the same except for the pipe diameter.
I tried to save as the pipe run to a new name and change pipe diameter but it gives me this error seen below. Do I have to make the whole run again? If i change run I have now to what I need for smaller frame I lose original sizes for first frame size.
Problems encountered while saving the document.
Save failed because the following files have been modified and must be saved together with Cooling_Skid_Type_I.Tube and Pipe Runs.iam:
Cooling_Skid_Type_II.Run01.iam,Cooling_Skid_Type_II.Route01.ipt,Cooling_Skid_Type_II.Route02.ipt,Cooling_Skid_Type_II.Route03.ipt,Cooling_Skid_Type_II.Run02.iam,Cooling_Skid_Type_II.Hose01.iam,Cooling_Skid_Type_II.Hose01.ipt
How to successfully swag the end of a tube or pipe?
View 9 Replies View RelatedI am a drafting instructor who has inventor 2013. Want resources (tutorial, instructional video...) explaining how to use "tube and Pipe design" with inventor 2013.
View 2 Replies View RelatedInventor Tube & Pipe can output ISOGEN files (*.pcf) for manipulation into piping isometrics via 3rd party software. I have done this and the pcf format is very poor on detail that it contains about each fitting. It required hours of manually re-writing the pcf file to get it to produce a result that was "good enough".
The Alias Isogen tool is rubbish - it crashes often, it does not make the changes that one has told it to etc. etc.
I eventually found Autodesk Plant 3D has an amazing piping capability (but it is 2D pretending to be 3D - so it cannot save as parametric solids) - however - it produces great piping isometrics. On studying the pcf from Inventor vs the pcf from Plant 3D for equivalent routes it is clear that Inventor is years behind in their piping functionality.
1. Does Inventor have plans to e.g. make their pcf compatible with Plant 3D so that we can process isometrics in that?
2. Any handy tool to manipulate pcf's to add e.g. welds, supports, notes, insulation, bolts, nipples/sockets/weldolets etc. to produce a comprehensive iso drawing?
I'm trying to draw the following bench in Autocad but I'm getting bogged down trying to figure out how to create the following tube with an angle on it and how to achieve different shapes at the top of tube.
View 9 Replies View RelatedI am having a problem changing my tube sizes. Basically when I create a new route and populate the route, I want to be able to change the size without adding hundreds of sizes to the library. So I right click on the tube and select change size. The when I select a different size and select apply nothing happens? I push update and still nothing happens?
When I try to change the tubing size again it shows the size that I change it to but the tube doesn't visually change? I have noticed the same with the hose. What I also noticed is when you change the size on pipes it does change. How it is possible to change the piping sizes by right clicking on it and select change size when this function doesn't seem to work on the tube and hose?
If I have a "large" tube with a series of holes along it, say 9mm diameter...
I have another component (an 8.9mm solid cylinder) which should be inserted in those holes......how is the best way of doing it?
I thought about adding a work axis in each hole, but can't find an easy way of doing even that!So how would you do it?
If I make a hole in a rectangular block it all works out, the toroid appears and I constrain the small 8.9mm to the axis of the hole in the block.That does not seem to work with holes in the large tube.
To draw the cope end I subtract one tube from the other, this creates a taper from wall thickness t at the intersection of the inner tube face to zero at the intersection of the outer wall face. This loss of wall thickness is not ideal. To get rid of this less than full thickness material I create a slicing plane through intersection of non-cut tube 1 and the inner wall of the tube to be cut, I establish this point by drawing a 2D cross section.
I realize this a bit of a hack and it never works out spot on as the slicing plan never seems to match exactly the intersection point of the 3D tube inner wall.
I have tried to get a work around. i.e. :
- drawing a tube inner radius only subtracting from that then shelling-this only re creates the taper.
-offsetting the intersection edge of the inner wall and trying to project onto outer at 90deg-this does not offset correctly due to the complex geometry.
Capture.jpg
1. How to create a mitre maintaining full wall thickness. 90 degree intersections.
2. How to create a mitre maintaining full wall thickness. Non 90 degree intersections.
3. How to create a mitre maintaining full wall thickness. Tubes angled in 2 planes i.e. : for triangular space truss.
4. How to create a mitre maintaining full wall thickness. Tubes angled in 2 planes centers lines not coincident ie internal members offset to enable 2/3 to meet at same node.
5. How to deal with the above when using non round tubes.
Set-up the Tube and Pipe functionality in Inventor 2012. Apparently it was not installed or configured at installation.
View 3 Replies View Related