AutoCAD Inventor :: Best Way To Insert One Tube Into Another Which Has Holes?
Jul 15, 2013
If I have a "large" tube with a series of holes along it, say 9mm diameter...
I have another component (an 8.9mm solid cylinder) which should be inserted in those holes......how is the best way of doing it?
I thought about adding a work axis in each hole, but can't find an easy way of doing even that!So how would you do it?
If I make a hole in a rectangular block it all works out, the toroid appears and I constrain the small 8.9mm to the axis of the hole in the block.That does not seem to work with holes in the large tube.
View 9 Replies
ADVERTISEMENT
Apr 9, 2013
I am trying to assemble an extruded tube that has holes drilled, to a flat plate to be bolted together. when i go to assemble the parts the drilled holes will not highlight to attach the plate to.
View 9 Replies
View Related
Oct 17, 2012
I want to make an assemby consisting of 3 parts. A crank shaft and a crank pin that screw into threaded holes in a crank disk. How can I insert them and prevent them rotating in their holes but still allow the whole assembly to rotate around the axis of the shaft? Also how could I lock a flywheel on to the shaft so that whole assembly can rotate togeather?
View 1 Replies
View Related
Mar 16, 2013
I have a question about calculating the maximum tube length. Why do i ask this, because you can just measure it on drawing?
I'm building a parametric model for building simple storage tanks, and the goal is to get a complete BOM out of the model without any difficulties.
I have 4 possibilities of tube positioning on the tank. (see image)
1. A tube that stands in the center of the axis of the main tank.
2. A tube that stands in the center of the axis of the main tank, but under an angle
3. A tube that doesn't stand in the center of the axis of the main tank.
4. A tube that doesn't stand in the center of the axis of the main tank, but under an angle
These 4 possibilities can be flush with the inside of the tank or not.
Is there a easy way to determinate the longest point from the front of the tube? This longest measurement will be the length i need to get into my description for the BOM.
View 1 Replies
View Related
May 27, 2013
How do I repair a tubing constraint?
I use tubing in inventor, I always attached tube to whatever fittings I am using and everything is fine but if something gets moved that the end of the tube loses its contraint I'm ready to jump off a cliff!
Is there any way to get the end of the 3D sketch contrained to the fitting again?
Up until now I have always had to deleted the route and started over. Inventor Pro 2014
View 1 Replies
View Related
Oct 10, 2013
I want to build a pipe or tube frame and use tube or pipe connectors to join the pipes.
What is the best way? "Tube and pipe" or "Frame generator"?
View 1 Replies
View Related
Nov 27, 2011
-Did I do the rectangular pattern correctly? If not, the correct one with step-by-step information
-Why the holes do not go through the thickness of plate?
View 8 Replies
View Related
Dec 3, 2013
What way do i add tube to the connectors.Should it be added in assembly or as a separate part?
Inventor 2013/2014
View 5 Replies
View Related
Apr 2, 2013
How to create spikes on tube. I've try several way, but no success. I've try to mate with holes on plate and than to bend half of the plate, but not succeed.
View 9 Replies
View Related
Jun 21, 2010
I'm looking to find how many holes there are in a part ( and then what their diameters are). I tried using
Dim oPartDoc As Document
Set oPartDoc = ThisApplication.ActiveDocument
Dim oCompDef As PartComponentDefinition
Set oCompDef = oPartDoc.ComponentDefinition
MsgBox "there are " & oCompDef.Features.HoleFeatures.Count & " holes"
but this falls down if a hole feature created more than one hole at the same time.
View 9 Replies
View Related
Dec 30, 2011
I have an existing extrustion with holes in it. All in one sketch.
I go to add an off shoot from the existing main body in the sketcher. In that off shoot I add a circle
in the middle of the off shoot to represent a hole. So fa so good, or at least I thought. I exit the sketch mode
and my extrustion looks fine with the exception of the hole is not there. Why? Why doesn't Inventor recognise the
circle sketch as hole geometry like it does in the originally created sketch?
In Solidworks, given this same scenario, would have recogized the circle as a void and thus created a hole.
I ended up deleteing the hole out of the main sketch and doing a seperate hole cut feature. I am sure I am missing something and in the process of learning would like to know if indead I did not do this the correct way.
View 6 Replies
View Related
Jun 18, 2012
how to get the tube and pipe add-on? I do not already have it and I have not been able to find much information on how to get it.
View 9 Replies
View Related
Dec 29, 2013
> In Inventor , here we see the orange color tube shown in the attached screenshot.
Attched File : Frames11
> But after zooming it nearby it’s get disappear as shown in the attached screenshot.
Attched File : Frames12
> One more shocking point is that we open this same drawing on other PC and there it’s display corrrectly.
Any solution for this hide tube. We are using:
Software : Inventor Ultimate 2014-64 Bit
Hardware : Workstation Dell Precision T3600
View 1 Replies
View Related
Aug 13, 2013
I am modelling plain Bearing but i have problem getting holes at an angles. I have attached an image for it.
Holes are located on top side of the bearing.
View 3 Replies
View Related
Dec 24, 2013
Im trying to reproduce the part attached. Its a rectangular aluminum tube. .320 x .180 approx an inch long. I tried lofting 2 sketches but the result does appear like the attached image.
View 8 Replies
View Related
Sep 30, 2013
Basically I’m trying to create a circular cut in a flat pattern for a hole made in a rolled piece of sheet metal.
I have created a "case" (this is what we call it) to mount an axial fan, it will require holes for mounting the motor plate. When I create these holes in the rolled case assembly they appear to be fine, but when I flatten it they are turned into two sets of semi-circles or ellipses.
This is only a problem when we run the parts on our Laser; the laser will attempt to start the cutting at the end of each of these "semi-circles" causing a hotspot where the two semi circles meet. This causes the hole to be slightly smaller than intended in this area causing great difficulty inserting bolts, they normally require drilling.
Our material thicknesses vary from about 3mm to 8mm.
I’ve included a crude example of what I’m trying to achieve. To really see what I mean, place the file into a Drawing file and zoom into the hole. I couldn't add the file, with only 3 features the file was 5mb in size.
By the way, I have a temporary solution, it's just a little complicated. (My solution: use square holes first in the un-flat, use the diagonal lines from each corner of the square in a sketch on the flat pattern to place a circular cut on its mid points.)
Intel Xeon 3.0GHz (4 Cores)
nVidia Quadro 2000 (1GB) - Dual Screen
8GB RAM
View 6 Replies
View Related
Nov 12, 2011
How I can get the holes filled/hatched in elveation vies and in sections?
Please see the attaced sketch.
View 9 Replies
View Related
Mar 20, 2013
Using the Hole command, I want to locate / reference off datums, this is something I can do in Pro-E. It's not a choice, that I can find.
View 8 Replies
View Related
Feb 14, 2012
I'm trying to do a usable and real flat pattern for a laser cut on this type of part and I'm not able to do a cut across bend or other wrap around face feature.
Any method to do such a feature ?
View 7 Replies
View Related
Oct 10, 2013
What is the best way to draw pipe frame using "KEE KLAMP" connectors?
Pipe and tube or frame generator?
View 9 Replies
View Related
Oct 28, 2011
I've been trying to make tube between these circles but I can't figure it out how to make it smooth. I tried sweep too but that didn't work too well. Here's picture of my try without sweep: [URL]
You see that it leaves corners on the back. I would like to have it so it's smooth and has same angle. How should I do it?
View 4 Replies
View Related
Oct 24, 2011
How do I place a hole on a circular part at a specified distance from the edge. This works on other parts with straight edges, but there is no option to do so on a circle.??
View 3 Replies
View Related
Sep 25, 2013
I inherited this assembly from another user. In making some dimensional changes the pipe runs have now errored.Not having ever taken any training courses in T&P, my knowledge is just based on simple straight forward runs.
This on the other hand is bit more complicated. As you can see from the image I have this one run that has errors.My question is with the violation, is there anyway to pinpoint exacty what the violating member is?
View 9 Replies
View Related
Jan 25, 2012
I have a couple of quick questions about dimensioning holes in drawings .
First, if I have a hole in a rod or shaft so the surface isn't a full circle I get the dimension as a radius. Can I change it to a diameter?
Second, in a model, how do I dimension or measure to the edge of a round rather than to it's center? In SW I could hold the shift key while selecting, is there a similar method here?
View 2 Replies
View Related
Sep 20, 2012
I have several parts to get cut for one of our customers.
The provided the pdf I have attached, and I need to create and .ipt so we can cut it on our tube laser.
This is getting the better of me on how I would put my work planes in order to get the correct angles.
How to accomplish this?
Lenovo Think Pad
Windows 7 SP 1
64 Bit.
Inventor 2013
ACAD Mechanical 2013
View 4 Replies
View Related
May 10, 2013
I'm just getting started using the Tube and Pipe environment for some of my work, and I've got what I'm hoping is a simple question with a simple answer. In the picture attached I've got a 1" pipe dropping down into a 8" pipe which I've disabled because it's a standard part right now and I want to replace it with a tube & pipe run. The thing I seem to have the hardest time doing when routing my pipes is aligning/offsetting my nodes with existing geometry in the assembly. In this case I want the end of the 8" pipe to be 12" offset from the centerline of the 1" pipe, and for the 8" pipe's centerline to be 12" below the bottom of the mezzanine's I-beam (as the standard part it is now). What's the best way to do this in the Tube and Pipe environment?
I tried "Include Geometry" from the "Create" panel but that only lets me create planes, which won't work with offsetting from the 1" centerline. However, SOMETIMES (it's a big sometimes) ALL of the options in the "3D Sketch" tab are available. When that's the case, I can go to the "3D Model" tab and create workpoints, axes, and planes. Sometimes, though, they're not all available, and I'm not able to place anything but planes. How I can change it so I can always use all the geometry of my assembly?
Also I'd like to know if constraing fittings and point-snapping routes to my assembly geometry in this way is the best way to do Tube and Pipe routes. Will doing this allow my routes to update if the assembly changes?
View 1 Replies
View Related
Apr 12, 2012
I have an assembly which consists of parts and holes, when I open a part the holes are not visible as they were created in the assembly - how do I display the holes for these parts that were created in the main assembly when opening a part file ?
View 9 Replies
View Related
Sep 19, 2013
I have a cabinet that we make, and we put some holes through the sheet metal skin of the cabinet at the assembly level. I use iLogic to turn these holes on and off, depending on configurations.
Sometimes when switching between configurations the holes that were suppressed will disappear from my model and leave me with just the original sketch. So my iLogic rule errors because it can't find the hole feature.
I am using planes based off of the origin planes to define an axis that I use as my hole center line. And I then make a sketch on the XY origin plane to create a point for my hole. So everything there is independent of the cabinet model.
View 3 Replies
View Related
Sep 24, 2010
I have just completed an assembly and in this assy. I have a tube and pipe run. The original frame holding this pipe was 1m*1m*2m. We are now building a smaller unit with the same design. The pipe run is exactly the same except for the pipe diameter.
I tried to save as the pipe run to a new name and change pipe diameter but it gives me this error seen below. Do I have to make the whole run again? If i change run I have now to what I need for smaller frame I lose original sizes for first frame size.
Problems encountered while saving the document.
Save failed because the following files have been modified and must be saved together with Cooling_Skid_Type_I.Tube and Pipe Runs.iam:
Cooling_Skid_Type_II.Run01.iam,Cooling_Skid_Type_II.Route01.ipt,Cooling_Skid_Type_II.Route02.ipt,Cooling_Skid_Type_II.Route03.ipt,Cooling_Skid_Type_II.Run02.iam,Cooling_Skid_Type_II.Hose01.iam,Cooling_Skid_Type_II.Hose01.ipt
View 3 Replies
View Related
Feb 20, 2013
I have a 3 part assembly . Holes have to be made though the 3 parts . The holes can be made and snet/projected/though all/though distance and this work fine. The holes are shown in each part and the participant command works fine
The holes are shown in a drawing file....all GOOD
BUT
The holes are NOT shown when each part is opened!
View 3 Replies
View Related
Jun 6, 2013
I am struggling to drill holes at an angle on shaft in assembly level. I cant drill at part stage as forging called up in assembly.
View 4 Replies
View Related
