I have an assembly which consists of parts and holes, when I open a part the holes are not visible as they were created in the assembly - how do I display the holes for these parts that were created in the main assembly when opening a part file ?
View 9 Replies
I'm trying to assemble two parts, each of which has four matching bolt holes.So I do a "mate" between a hole on one and a hole on the other. This works fine, and the parts now behave just like two parts bolted together with one bolt - one can be rotated relative to the other around the bolt hole. So there is one degree of freedom left to be constrained.
But the obvious ways to constrain that one last rotational constraint result in overconstraint. Trying a "mate" between the circles at the ends of the corresponding bolt holes breaks the first constraint, and the non-grounded object "jumps". Trying to auto-mate the two holes results in the holes being constrained as tangent, with the holes not lined up. I've tried constraining the center points of the end circles of the holes. That doesn't work right either.
Doing the second constraint as "tangent-inside" does work. That's a 1 DOF constraint, which makes sense.It took me a while to figure that out. The help files aren't very useful when multiple constraints are involved.
-Did I do the rectangular pattern correctly? If not, the correct one with step-by-step information
-Why the holes do not go through the thickness of plate?
I am trying to replace a custom part - created from a content center part - with a copied part with a different name. (I am using the replace tool in an assembly.) However, Inventor is not replacing the part with the part I pick but rather the content center version of it.
View 3 Replies View RelatedOn the main sheet of my drawing I have the overall Parts List. Shows almost all parts except for the few that we don't want to list. On the second sheet I inserted a Parts List to show only parts that are shown in a detail on that page, made the rest non-visible.
On the main sheet there is an item (#13) that has a QTY of 3. Two of those Three are optional parts. What I'm trying to do is insert a custom part into the Parts List, give it an item number of 13A and put in the description "OPTIONAL", then do an Override in the balloon to show 13A.
I get it in the Parts List, Apply it, close it, save the drawing. Looking at the Parts List, item #13A is there, but item #14 is gone. I go back into the Parts List and 13A is there and there's a blue box around the item # and the description. I uncheck Static Value and number 14 shows up (item # and the description).
Then I go over to sheet two, open that Parts List and it lists 13A at the bottom with all the info I added in sheet one and it's non-visible. Go back to sheet one, open the Parts List and there is no 13A to be found.
I am working on an assembly that is designed around a box (bounding box) that could change size. I modeled the bounding box and placed it in a new assembly file. All other parts have been created within the assembly by referencing that bounding box with starting work plane and project geometry.
The problem comes in when I change the bounding box dimensions. The work planes for each additional part, which were defined by the faces of the bounding box, do not move when the sides move. Also, my projected geometry is not updating correctly. This is a simple box, with all 90° corners. So, all associated parts (at this point) are just rectangles.
My parts list on my idw do not update when I make changes to the model. Specifically, I have deleted a bolted connection on my design and replaced with a different components but the parts list table does not update - all I see is a lightning bolt in the browser next to the parts list but I cannot update it here.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I was using virtual parts to add nuts and bolts to a drawing in 2013
I can make a VP bolt in the assembly, no problem, set it's size, weight, etc.
In the VP itself, there is no option for number of bolts I want it to emulate. For arguement's sake the weight was 1 pound per bolt (they are big bolts).
I can go into the BOM and say quantity 60, hit done and save the assembly.
If i open the drawing, the parts lists shows 60lbs for the 60 bolts total - which it should when summing the weight.
The problem is the BOM/assembly. If the weight of my assembly (without bolts) is 10,000lbs, the assembly sees the VP weighing 1lb and says the total weight is 10,001 lbs. Am i going to have to pattern a fake part to get this to work right? Shouldn't the total weight take into account the quantity set in the Bom??
Is there a way to display the density of materials that are assigned to varius parts in the parts list on a drawing? I don't need the mass of the parts I just need the material density to show up next to their respective parts.
For example, if I have a part with [steel mild] material assinged to it (no matter the size) I need a column in the BOM on the drawing to show: 490.684 lbs/ft^3. "Worry when there's something to worry about."
I'm looking to find how many holes there are in a part ( and then what their diameters are). I tried using
Dim oPartDoc As Document
Set oPartDoc = ThisApplication.ActiveDocument
Dim oCompDef As PartComponentDefinition
Set oCompDef = oPartDoc.ComponentDefinition
MsgBox "there are " & oCompDef.Features.HoleFeatures.Count & " holes"
but this falls down if a hole feature created more than one hole at the same time.
I have an existing extrustion with holes in it. All in one sketch.
I go to add an off shoot from the existing main body in the sketcher. In that off shoot I add a circle
in the middle of the off shoot to represent a hole. So fa so good, or at least I thought. I exit the sketch mode
and my extrustion looks fine with the exception of the hole is not there. Why? Why doesn't Inventor recognise the
circle sketch as hole geometry like it does in the originally created sketch?
In Solidworks, given this same scenario, would have recogized the circle as a void and thus created a hole.
I ended up deleteing the hole out of the main sketch and doing a seperate hole cut feature. I am sure I am missing something and in the process of learning would like to know if indead I did not do this the correct way.
I have an assembly with a lot of purchased parts. I need to create a buy out list for purchasing. I've done this many times in the past and have a template set up for this purpose.
So now the problem, In this assembly, I have subassemblies showing up on my parts only parts list.
One of the subassemblies cinsists of two purchased parts. Both parts are set to purchased in the Bill of materials. If I do a parts only list on this assembly, it works as expected, showing two purchased parts. However, if I put that assembly into a higher level assembly, A parts only parts list shows the assembly instead of the individual parts.
IV 2010 Suite
Been working over an idw MANY times due to project lag.Today I opened it up and tried adding balloons to an already ballooned assembly.
The parts list has not changed, and is "structured".But, if I try adding balloons, they tag each part, not the entire assembly.
Also, I verified this by trying to add another parts list, which defaults to "parts only".
I can't show my data set, b/c it's HUGE, plus it's proprietary.
IV 2010 Suite
Digital Storm PC:
EVGA & Intel components
Win 7 Pro 64 bit
I am modelling plain Bearing but i have problem getting holes at an angles. I have attached an image for it.
Holes are located on top side of the bearing.
Basically I’m trying to create a circular cut in a flat pattern for a hole made in a rolled piece of sheet metal.
I have created a "case" (this is what we call it) to mount an axial fan, it will require holes for mounting the motor plate. When I create these holes in the rolled case assembly they appear to be fine, but when I flatten it they are turned into two sets of semi-circles or ellipses.
This is only a problem when we run the parts on our Laser; the laser will attempt to start the cutting at the end of each of these "semi-circles" causing a hotspot where the two semi circles meet. This causes the hole to be slightly smaller than intended in this area causing great difficulty inserting bolts, they normally require drilling.
Our material thicknesses vary from about 3mm to 8mm.
I’ve included a crude example of what I’m trying to achieve. To really see what I mean, place the file into a Drawing file and zoom into the hole. I couldn't add the file, with only 3 features the file was 5mb in size.
By the way, I have a temporary solution, it's just a little complicated. (My solution: use square holes first in the un-flat, use the diagonal lines from each corner of the square in a sketch on the flat pattern to place a circular cut on its mid points.)
Intel Xeon 3.0GHz (4 Cores)
nVidia Quadro 2000 (1GB) - Dual Screen
8GB RAM
How I can get the holes filled/hatched in elveation vies and in sections?
Please see the attaced sketch.
Using the Hole command, I want to locate / reference off datums, this is something I can do in Pro-E. It's not a choice, that I can find.
View 8 Replies View RelatedHow do I place a hole on a circular part at a specified distance from the edge. This works on other parts with straight edges, but there is no option to do so on a circle.??
View 3 Replies View RelatedI have a couple of quick questions about dimensioning holes in drawings .
First, if I have a hole in a rod or shaft so the surface isn't a full circle I get the dimension as a radius. Can I change it to a diameter?
Second, in a model, how do I dimension or measure to the edge of a round rather than to it's center? In SW I could hold the shift key while selecting, is there a similar method here?
I have a cabinet that we make, and we put some holes through the sheet metal skin of the cabinet at the assembly level. I use iLogic to turn these holes on and off, depending on configurations.
Sometimes when switching between configurations the holes that were suppressed will disappear from my model and leave me with just the original sketch. So my iLogic rule errors because it can't find the hole feature.
I am using planes based off of the origin planes to define an axis that I use as my hole center line. And I then make a sketch on the XY origin plane to create a point for my hole. So everything there is independent of the cabinet model.
I have a 3 part assembly . Holes have to be made though the 3 parts . The holes can be made and snet/projected/though all/though distance and this work fine. The holes are shown in each part and the participant command works fine
The holes are shown in a drawing file....all GOOD
BUT
The holes are NOT shown when each part is opened!
I am struggling to drill holes at an angle on shaft in assembly level. I cant drill at part stage as forging called up in assembly.
View 4 Replies View RelatedCurrent version INV 2012
1. When placing pumps,bolt-on walkways etc..etc..on to a metal frame at the assembly level do you place the pumps/walkways first and then add the bolt holes to the frame or do you create the bolt holes first in the frame and then place the pump/walkways on to the holes?
i have edited an associative part within an assembly. Created a sketch on one of the surfaces, and projected the surface of another part, which had holes. Then created a set of holes, by selecting some of the hole centers from this projected sketch. Later I wanted to remove one of these holes, but it doesn't seem to be possible. I can not de-select a point.
Inventor 2011
I am trying to Drill a series of holes on a cylinder. I cannot find out how to start the sketch on this surface so that i can drill on the rounded part of the cylinder.
View 5 Replies View RelatedI have a problem with a model and the drawing. In the model i have mirrored some holes. In the drawing the hole-table shows some of the mirrored holes on the position of the original ones. Also some entries are doubled.
I have also tried to redo a fresh drawing, the problem persists.
System: Inventor 2011 64 bit Subscription bonus pack with sp2
I also tried o another system without change. The model is too big to attach, so i attached only a pdf-dok.
I seem to have made what many might consider a rookie mistake. Built a fairly complex structure for an overhead crane system and get to the end to find that I missed two holes. The problem with these two holes is it is ONLY 1 plate (my grounded part), but I have used this same part in one other instance. So if I edit (even from within assembly) and add the two holes to the grounded plate it creates them in the other plate, which I dont want.
Since I have the second plate being used as a refence to locate MANY other parts on this unit, it would be quite difficult to replace it with a new part (same but different file name).
Any way to add said two holes to the grounded plate only and not the other?
Inventor 2014 PDS
If I have a "large" tube with a series of holes along it, say 9mm diameter...
I have another component (an 8.9mm solid cylinder) which should be inserted in those holes......how is the best way of doing it?
I thought about adding a work axis in each hole, but can't find an easy way of doing even that!So how would you do it?
If I make a hole in a rectangular block it all works out, the toroid appears and I constrain the small 8.9mm to the axis of the hole in the block.That does not seem to work with holes in the large tube.
I created an ipart and on some of the parts i need holes in them and the others i do not. I use the hole feature and made my holes but it shows up on all of the parts. I go into the table and change all the holes for the parts i don't need to a dia of 0. now those parts wont work because of the error of having the hole dia set to zero.
Is there a way i can suppress the holes on the parts i don't what the holes to be in?
want to delete holes (see picture), but also to keep other features below hole.
View 3 Replies View RelatedI have a .idw that I'm trying to make a parts list on. I select parts list and highlight everything. There are two screws that are not showing up on the parts list. I cannot select them manually either. It's acting like they are not there. Even if I do a complete parts list (adding the assemblies parts into one big list), they still don't show up.
How can I select these parts? What is wrong with them that they do not show up in the parts list?
