i have edited an associative part within an assembly. Created a sketch on one of the surfaces, and projected the surface of another part, which had holes. Then created a set of holes, by selecting some of the hole centers from this projected sketch. Later I wanted to remove one of these holes, but it doesn't seem to be possible. I can not de-select a point.
Inventor 2011
I have a sheet metal part which has several holes in, from which I have created a hole table. The hole table does not list all the holes in my part as I am only permitted to to select holes on one face of the part in the selected view. I have tried selecting all holes on the Isometric view however I cannt do this either.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I have a part with multiple holes created in a single hole feature (i.e. not patterned but made by selecting multiple sketch center points). As desired, the holes all have the same size since they all fit the same fastener. Is there a way to easily assemble fasteners to all the holes? Currently, I am using insert for each fastener and this gets tedius if there are many holes. Additinally, if the number of holes changes, a manual update is required. I'm hoping there is something that works similar to associative patterns.
INV 2013
I've got a template with a set of Object defaults for an Inch drawing and a set for a Metric drawing. I've just noticed that within my metric set, if I insert a hole table with tapped holes, the font on the tapped holes doesn't match the other hole types. I'm searched around, but all the settings for the hole table style reference the same text style. (Please see the attached image.)
So is there a way to set a certain hole type to have a certain font or size within a hole table? Because if there is, I'd obviously like to remove it..... But I can't seem to figure out where the issue is.
I am trying to add a hole to an existing hole chart. I drop the part into a new drawing, set the ordinate "zero", and add a hole chart by selecting a few holes. When I attempt to edit the chart: click chart, right click "edit", click add hole, select new holes, right click to create, the "create" selection is greyed out and all I have to choose from is cancel. I searched the forum here but could not find a reference to this a know issue. Am I doing something wrong or is this a glitch of 2013.
We are running win7 x64 machines and this happens on both the 2013 Ultimate and Premium editions of the product.
I have had this problem intermittently for a few weeks since going to Inventor 2013 SP1.1. I have a part within an assembly and that part has holes created in it before assembling it with other parts. Now when I try and create a hole table in a drawing of the assembly I cannot select hole edges and the hole table is blank when trying to create it automatically from view selection. I originally thought it may be an alignment issue but I have since aligned everything correctly and it still persists. I can create the hole table if I import in just the part into the drawing but it will not allow me to create the table on the whole assembly.
I can also create the hole table if I use "centred pattern" and create cross hairs on all of the holes however it does not give me correct annotations for the holes as shown in attachment and I can manually change the annotations but seriously this should not be required. As shown in the screen shot it reads as A1 down to K1 instead of A1 to A10. .
Question: Is it possible to control the Hole Dimensions called out on the Hole Chart? As in controling leading/trailing zeros for main hole dim, alt home dim and tolerances? Can you combine the Main Dim with the Alt dim in a single column, separated with parentheses? (same with tolerance?)
View 5 Replies View RelatedI would like to use the hole command to place a hole in a part. When I place the hole it won't allow me to use one of the origin planes to locate the hole from. Can I only locate holes off edges?
View 4 Replies View RelatedI have an assembly that contains a part and a hole feature (the hole feature is at the assembly level). Using the api, I'm trying to get the hole location relative to the part's coordinate system in a without using the holeplacementdefinition.distance property, this way I can get the hole location regardless of the way it was defined.
View 2 Replies View Relatedi use hole feature names in hole table.
i assign hole names attribute to hole feature but dont get attribute hole table.
how to get hole names in hole table.
While creating holes in a part, a small counter shows (when you click on a point) of how many holes there are.
Programs:
Solidworks (1998-2011)
Autodesk Inventor (R8 - 2013)
Autodesk AutoCad 2D
Autodesk AutoCad 3D
Catia V5
SolidEdge
Anvil (Very old program!)
Pro/E
-Did I do the rectangular pattern correctly? If not, the correct one with step-by-step information
-Why the holes do not go through the thickness of plate?
I'm looking to find how many holes there are in a part ( and then what their diameters are). I tried using
Dim oPartDoc As Document
Set oPartDoc = ThisApplication.ActiveDocument
Dim oCompDef As PartComponentDefinition
Set oCompDef = oPartDoc.ComponentDefinition
MsgBox "there are " & oCompDef.Features.HoleFeatures.Count & " holes"
but this falls down if a hole feature created more than one hole at the same time.
I have an existing extrustion with holes in it. All in one sketch.
I go to add an off shoot from the existing main body in the sketcher. In that off shoot I add a circle
in the middle of the off shoot to represent a hole. So fa so good, or at least I thought. I exit the sketch mode
and my extrustion looks fine with the exception of the hole is not there. Why? Why doesn't Inventor recognise the
circle sketch as hole geometry like it does in the originally created sketch?
In Solidworks, given this same scenario, would have recogized the circle as a void and thus created a hole.
I ended up deleteing the hole out of the main sketch and doing a seperate hole cut feature. I am sure I am missing something and in the process of learning would like to know if indead I did not do this the correct way.
I am modelling plain Bearing but i have problem getting holes at an angles. I have attached an image for it.
Holes are located on top side of the bearing.
Basically I’m trying to create a circular cut in a flat pattern for a hole made in a rolled piece of sheet metal.
I have created a "case" (this is what we call it) to mount an axial fan, it will require holes for mounting the motor plate. When I create these holes in the rolled case assembly they appear to be fine, but when I flatten it they are turned into two sets of semi-circles or ellipses.
This is only a problem when we run the parts on our Laser; the laser will attempt to start the cutting at the end of each of these "semi-circles" causing a hotspot where the two semi circles meet. This causes the hole to be slightly smaller than intended in this area causing great difficulty inserting bolts, they normally require drilling.
Our material thicknesses vary from about 3mm to 8mm.
I’ve included a crude example of what I’m trying to achieve. To really see what I mean, place the file into a Drawing file and zoom into the hole. I couldn't add the file, with only 3 features the file was 5mb in size.
By the way, I have a temporary solution, it's just a little complicated. (My solution: use square holes first in the un-flat, use the diagonal lines from each corner of the square in a sketch on the flat pattern to place a circular cut on its mid points.)
Intel Xeon 3.0GHz (4 Cores)
nVidia Quadro 2000 (1GB) - Dual Screen
8GB RAM
How I can get the holes filled/hatched in elveation vies and in sections?
Please see the attaced sketch.
Using the Hole command, I want to locate / reference off datums, this is something I can do in Pro-E. It's not a choice, that I can find.
View 8 Replies View RelatedHow do I place a hole on a circular part at a specified distance from the edge. This works on other parts with straight edges, but there is no option to do so on a circle.??
View 3 Replies View RelatedI have a couple of quick questions about dimensioning holes in drawings .
First, if I have a hole in a rod or shaft so the surface isn't a full circle I get the dimension as a radius. Can I change it to a diameter?
Second, in a model, how do I dimension or measure to the edge of a round rather than to it's center? In SW I could hold the shift key while selecting, is there a similar method here?
I have an assembly which consists of parts and holes, when I open a part the holes are not visible as they were created in the assembly - how do I display the holes for these parts that were created in the main assembly when opening a part file ?
View 9 Replies View RelatedI have a cabinet that we make, and we put some holes through the sheet metal skin of the cabinet at the assembly level. I use iLogic to turn these holes on and off, depending on configurations.
Sometimes when switching between configurations the holes that were suppressed will disappear from my model and leave me with just the original sketch. So my iLogic rule errors because it can't find the hole feature.
I am using planes based off of the origin planes to define an axis that I use as my hole center line. And I then make a sketch on the XY origin plane to create a point for my hole. So everything there is independent of the cabinet model.
I have a 3 part assembly . Holes have to be made though the 3 parts . The holes can be made and snet/projected/though all/though distance and this work fine. The holes are shown in each part and the participant command works fine
The holes are shown in a drawing file....all GOOD
BUT
The holes are NOT shown when each part is opened!
I am struggling to drill holes at an angle on shaft in assembly level. I cant drill at part stage as forging called up in assembly.
View 4 Replies View RelatedCurrent version INV 2012
1. When placing pumps,bolt-on walkways etc..etc..on to a metal frame at the assembly level do you place the pumps/walkways first and then add the bolt holes to the frame or do you create the bolt holes first in the frame and then place the pump/walkways on to the holes?
I am trying to Drill a series of holes on a cylinder. I cannot find out how to start the sketch on this surface so that i can drill on the rounded part of the cylinder.
View 5 Replies View RelatedI have a problem with a model and the drawing. In the model i have mirrored some holes. In the drawing the hole-table shows some of the mirrored holes on the position of the original ones. Also some entries are doubled.
I have also tried to redo a fresh drawing, the problem persists.
System: Inventor 2011 64 bit Subscription bonus pack with sp2
I also tried o another system without change. The model is too big to attach, so i attached only a pdf-dok.
I seem to have made what many might consider a rookie mistake. Built a fairly complex structure for an overhead crane system and get to the end to find that I missed two holes. The problem with these two holes is it is ONLY 1 plate (my grounded part), but I have used this same part in one other instance. So if I edit (even from within assembly) and add the two holes to the grounded plate it creates them in the other plate, which I dont want.
Since I have the second plate being used as a refence to locate MANY other parts on this unit, it would be quite difficult to replace it with a new part (same but different file name).
Any way to add said two holes to the grounded plate only and not the other?
Inventor 2014 PDS
If I have a "large" tube with a series of holes along it, say 9mm diameter...
I have another component (an 8.9mm solid cylinder) which should be inserted in those holes......how is the best way of doing it?
I thought about adding a work axis in each hole, but can't find an easy way of doing even that!So how would you do it?
If I make a hole in a rectangular block it all works out, the toroid appears and I constrain the small 8.9mm to the axis of the hole in the block.That does not seem to work with holes in the large tube.
I created an ipart and on some of the parts i need holes in them and the others i do not. I use the hole feature and made my holes but it shows up on all of the parts. I go into the table and change all the holes for the parts i don't need to a dia of 0. now those parts wont work because of the error of having the hole dia set to zero.
Is there a way i can suppress the holes on the parts i don't what the holes to be in?
want to delete holes (see picture), but also to keep other features below hole.
View 3 Replies View Related