I am trying to make dynamic blocks to show reinforced slab bars detail. Attached herewith is a dynamic block which shows the bars. Now i want to attach a leader to the block (having framed text) whose text values may vary from a, b, c, d, to say k. Is there anyway by which is can have the preset values that can be picked from a pull down menu.
View 5 RepliesI have a dynamic block that I want to be added to a leader style. When I create the style and draw a leader I don't have access to the dynamic block functionality. Is there a way to restore this functionality without exploding the leader?
View 5 Replies View Relatedi have a dynamic block that my firm has been using. we're updating our dimstyles - and our new leader is a custom (close to open 30 but with heavy accents).
anyway - i'm a little new and vague as how to change the leader within the dynamic block. i fiddled with it several times - but with no success.
i have a dynamic block that my firm has been using. we're updating our dimstyles - and our new leader is a custom (close to open 30 but with heavy accents).
anyway - i'm a little new and vague as how to change the leader within the dynamic block. i fiddled with it several times - but with no success.
I have attached necessary files with this post
I designed a dynamic block to represent the profile of boreholes, and its different layers (depths, in profile) are linked to the respective description text by a leader.
Problem is when I flip the text with its leader, the tip of the arrow loses contact with the borehole. And as I flip more times, the further it gets from its original position.
I am new to dynamic blocks. I have figured out how to use the Properites block for "preset" definitions but we offer a product in infine sizes (within limits). For example the width may range from 30" to 200" in fractional increments which is impossible to set up presets. Is there a way that a person can set up the properties block so that a person would be prompted to enter required information, I.E. Width = xx", Height = xx" etc.?
View 3 Replies View RelatedIs there anyway to prevent AutoCAD from converting a MTEXT leader with a block element attached to a BLOCK leader when doing a copy/paste? See screen shot.
2012-04-05 3-09-00 PM.jpg
I was wondering if it would be possible to convert an existing block to a leader that uses the same block with the arrow attached without losing the information which is stored inside the block attributes.
I have created the multi leader with the block definition attached but I'm still struggling to incorporate the data into it.
There are to many blocks to do this manually. I have exported the data to a excel but do not know how to insert it back into to multi leader.
I am working with room tags that has multiple yes/no features. my problem is its hard aligning text because they wont snap to centers or refernece lines. How are people working with this. It causes for sometimes the leader line when used to not want to be straight or leaves some funky angle when change scale
View 1 Replies View RelatedIs there a way, using dynamic blocks, to rotate a line around an ellipse, so that that leader is always centered with the center of the ellipse, but it actually starts at the circumfrence of the ellipse.
Like with a circle, you choose, rotation, using the center of the circle as the base point, and then setting your radius, and choosing the 'rotate' action. I need to do basically the same thing, but with an ellipse.
I have a square with a solid hatch as a point, with a visibility on it, and a text attribute with a leader from the square to the atrabute. This is the part i understand. the part that is confusing is when I try to rotate the attributes arount the square, how to i keep the leader attached to the square, and still look like a correct leader?
View 2 Replies View Related1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.
is there an way to display attribute data using a multi-leader inside a single dynamic block.
To elaborate, I'm trying to create a borehole dynamic block that I can enter the ground level and end of borehole level as attributes, and have them show up in a multi-leader. The reason for the multi-leader is that I can add a background mask to it and it automatically adjusts the length of the outline obox around it.
I just want to insert the borehole block from a tool palette, enter a couple of attributes, stretch the bottom down to whatever level, and I'm done.
I've been playing with it all weekend trying to get fields to show the attributes and I can get it to work if I use another block for the levels (multi-leaders), but even then I have to into the fields an mess with them. It's go to be east so my CAD guys can do it without slowing down, otherwise they may as well carry writing everything out long-hand as they do now.
I'm using Civil 3D 2012, if that matters.
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies View RelatedI need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies View RelatedI need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"
Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?
I'm working on a drawing and I want an action to work on two diffrent dynamic blocks.
In my case, I wish to have two blocks that I can rotate by one rotation grip.
How do I manage to work this out?
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
I would like to create a "wave" dynamic block, see below...
It is made from wipeout.
Is it chance to make a similar?
If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?
Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
LT 2012 user
AutoCAD LT 2012
Windows 7 - 64 bit
I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).
View 9 Replies View RelatedI am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered
I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.
I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.
LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi
Then, I use command DAL; I can select dimension want use.
How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.
View 2 Replies View RelatedI have an X centered as my insertion point.
When I stretch the dynamic block for a larger area the X stretches but into the next single box but not centered within the double space.
how to get the X to be centered in the box when it is enlarged to a double or triple size?